similar to: PPPoE w/ "static" /29 ip range, how is it done?

Hi all, I am trying to install the PPPoe server rp-pppoe-3.8 from Roaring penguin on centos PC (Centos 4.3, Kernel release 2.6.9-34.EL) but not able to start it. When I start it it gives the error-- /etc/rc.d/init.d/pppoe status pppoe-status: Link is down (can't read pppd PID file /var/run/pppoe.conf-pppoe.pid.pppd) ror - /etc/rc.d/init.d/pppoe start Bringing up PPPoE

Peter Jakobi wrote: > Hi Jiri, > > you already tested an ancient userspace-only rp-pppoe? > I''ve still one active, and trying this you could validate > your the rest of your setup, before looking at possible > kernel changes anew (strace, ltrace, logs, whatever)... > Hi Peter. No I did not. Do I have to compile it? Can you give me more info what to do?

I have a requirement which I guess it is not too unusually, however I haven''t quite figured out how to do it and couldn''t find any examples which handle that. I have made myself a Linux-based bridge, eth0 bridged with eth1 to form br0. In this bridge, I run ''tc'' script to handle QoS. So far nothing unusual. However, what''s different is that this

Hello, My system is: Server with Slackware 8.1 LINUX, ADSL Internet with PPPoE connection, and I masquerade my LAN. I use "Roaring Penguin" PPPoE client for my ADSL connection. I would like to connect another ADSL line (also PPPoE) to my server and have two lines, because I want to make "Simple source policy routing", as described in LARTC HOWTO. How should I set up my

hi all. i am currently now serving PPPoE in my area. i had a script generated from tcng that worked perfectly before i started serving PPPoE. the issue is not in the script it self BUT in that "tc" code is not shaping on the ethernet anymore BUT INSTEAD on the pppX devices. I tested it and talking jargon, what should i do? The issue is that for each PPPoE login, PPPoE-server

Hi, I want a way to traffic shape pppoe encapsulated pkts based on its src/dst Ip address. Is there any way I can mark pppoe encapsulated pkts? Samit

Guys After reading through the archives I found some insightful ways to be able to shape traffic to pppoe clients from the server. I have two questions on the topic of setting up a pppoe server however... 1. The clients will all be connected to each other using a normal ethernet network, the segments connected with managed switches. The capacity is roughly 500 nodes. Will these pppoe sessions

My provider is getting ready to switch my DSL router to bridging mode and I supply the router (so I can get no only IPv4 addresses but also IPv6 addresses!). Here are his 'instructions' to me: "Basically you start pppoe, I give you the username and password for it, and then I set the router to passthrough modem mode, and you initiate the PPPoE session directly with my LNS back

Dear all, Though this is not LARTC related question, finding no other help I am forwarding this question for this group. Hope some GURUZ will help me. I want to authenticate my lan users through pppOE. I am using rh 9.0 box as my gateway. How / Which software do i use on my linux box to provide pppOE service and in client end win98/2000/Xp which software do i use?

My Internet gateway is using ADSL PPPoE connection with dynamic public IP assigned by ISP. My Internet gateway is Redhat AS3 U2, shorewall 2.0.9 As my ISP provided 4 simultaneous pppoe dailup connection for the same physical adsl line. My linux server can be configured for multiple pppoe connection i.e. ppp0, ppp1, ppp2, ppp3 Is it possible of shorewall to assigned say ppp0''s IP is

Greetings, I've just upgrade a home server to CentOS 6.5 with a new dual-core processor and mobo. I see that with the CentOS 6.x release rp-pppoe can be run as a daemon. I've looked through some online one-page setup notes for rp-pppoe, but nowhere is there a discussion of running it as a daemon. Until now, I've cobbled an ifcfg-ppp0 file and placed it in

Hello to everyone, Can someone help me with hints on how to configure a pppoe gateway on a linux box with 200+ clients behind it ? I''ve read that user-space daemons give A LOT of CPU overhead. I''m opened to ANY solution ! -- Radu Cugut mobile: +40 742 045686 web: http://rcugut.has.it

helo again. I think this question i am asking is worth: we know that pppoe-server creates a pppX device on each connection done to it. So, when i have to shape, i have to shape each pppX connection device on itself alone. What i know is that the borrowing method on one device by itself, e.g. ppp0, alone using HTB or the like. this means that i have to create for another device, e.g. ppp1,

Hi all I get a Cisco 1841 router, connecting the office through a CHAP PPPoE link: [...] interface Dialer1 ip address negotiated ip mtu 1492 ip nat outside ip virtual-reassembly encapsulation ppp ip tcp adjust-mss 1452 dialer pool 1 dialer-group 1 no cdp enable ppp authentication chap callin ppp chap hostname username at isp ppp chap password 0 s0meStr0ngP4sswd [...] As

I am a newbie to linux and shorewall. I am reading the shoreall quickstart guides. I am a bit confused about the following statement: ----------- quote -------------- The firewall has two network interfaces. Where Internet connectivity is through a cable or DSL "Modem", the External Interface will be the ethernet adapter that is connected to that "Modem" (e.g., eth0) unless you

I am having a little trouble getting my head around this so any help would be appreciated. I have just signed up a new service and have been allocated the following subnet which gives me 30 usable IP addresses. 210.15.xxx.192/27 The connection is made via pppoe which works fine and the connection creates ppp0 and assigns 210.15.xxx.193. Now I want to use 4 IP''s in a DMZ and the reset

Hi all Does anyone know how to set up internet access when running pppoe? Regards Nick _________________________________________________________________ Downloaden Sie MSN Explorer kostenlos unter http://explorer.msn.de/intl.asp

I need some suggestions, I want to limit the up and down bandwidth of PPPoE users that are terminated on a Linux router (kernel 2.6). What are my options, can I apply tbf qdisc on a ppp interface? That would limit the download, what about the upload? Any suggestions are welcome. -- damjan | дамјан This is my jabber ID --> damjan@bagra.net.mk <-- not my mail address!!!

I need basic PPPoE startup help. adsl-start DID bring up my PPPoE link (ppp0) to my ISP over eth0 via the DSL modem/bridge. My IPv4 CIDR block is routing and Shorewall is doing the firewalling. But shorewall has to be started after ppp0 is up and working. For now this means running shorewall restart (or start?). Shorewall 4.2 will have a way to restart shorewall without recompiling, I

Hi, we are currently using pppd to connect to the net through pppoe. Some providers seem to propose ipoe instead of pppoe and I cannot find any clue on how/where/if_possible to set up such connection in CentOS. Anybody has any experience with ipoe...? Thx, JD