similar to: Little question about imq device

Hi I try setup imq pseudo device for shaping I''m work such script #!/bin/sh TC=/sbin/tc /sbin/modprobe imq numdevs=1 /sbin/ip link set imq0 up $TC qdisc add dev imq0 handle 1: root htb default 1 $TC class add dev imq0 parent 1: classid 1:1 htb rate 10mbit # client1 tunnel tunnel $TC class add dev imq0 parent 1: classid 1:2 htb rate 256kbit $TC filter add dev imq0 protocol ip parent 1:0

Hi all, my IMQ device works OK (thanks to Andy Furniss), but now I''ve problems to attach the traffic in the qdisc''s. This is my conf: ----------------------------------------------------------------------- INET | |eth0 300Kbps ROUTER (NAT) |eth1 | LAN ----------------------------------------------------------------------- MAX=300 tc qdisc add dev imq0 root handle 1: htb

hi stef oone more pb while shaping incoming traffic with imq .this one tc qdisc add dev imq0 root handle 1: htb default 20 tc class add dev imq0 parent 1: classid 1:1 htb rate 2mbit burst 15k tc class add dev imq0 parent 1:1 classid 1:10 htb rate 1mbit tc class add dev imq0 parent 1:1 classid 1:20 htb rate 1mbit tc qdisc add dev imq0 parent 1:10 handle 10: pfifo tc qdisc add dev imq0 parent

Hello, I''ve just recently started to use IMQ and I got puzzled after seeing the imq usage example on the linuximq.net site: It was something like this: tc qdisc add dev imq0 handle 1: root htb default 1 tc class add dev imq0 parent 1: classid 1:1 htb rate 1mbit tc qdisc add dev imq0 parent 1:1 handle 10: htb default 5 tc class add dev imq0 parent 10: classid 10:1 htb rate 256kbit

Is there an other place than www.docum.org where one could get monitor_tc.pl? Docum.org seems to be down. Peter -- The bogosity meter just pegged.

Hi All, I''m trying to create a contended section of bandwidth using IMQ. I have the imq0 device up and running, with traffic passing through it. Firstly, I need to throttle the entire device imq0 to 2mbit/s. I would then like to add throttle rules for individual IP addresses, allowing them to pass up to 512kbit/s each, as long as imq0 has not reached its 2mbit/s. The configuration

Hi all and tc Gururs i have patched the IMQ and htb to kernel, but when i do egress filtering, iam not able to see any traffic and excusted the following the commands modprobe imq numdevs=1 tc qdisc add dev imq0 handle 1: root htb default 1 tc class add dev imq0 parent 1: classid 1:1 htb rate 100kbit tc qdisc add dev imq0 parent 1:1 handle 10: htb default 1 tc class add dev imq0 parent

ive got such network: |--------| |-------------| | WORLD |---|ROUTER/server| ------ NATED LAN |--------| |-------------| I want to use imq on ROUTER, what behaviour to choose ? AA, BA, AB, BB ?? --

Hello I have a server with a dsl connection on eth1 and local interface eth0. Because of the NAT i cannot direct traffic to IMQ device in PREROUTING chain but have to use INPUT and FORWARD. So i use rules. iptables -t mangle -A INPUT -i eth1 -j IMQ --todev 0 iptables -t mangle -A FORWARD -i eth1 -j IMQ --todev 0 And now the strange thing: FORWARD traffic gets directed nicely to the IMQ, but

Hello, I am using the IMQ with iptables (latest versions) and asking all packets to be enqueued to IMQ0 from both prerouting and postrouting (using different iptables rules to mark different streams). When I do this I get the kernel saying: "Dead loop on netdevice imq0, fix it urgently!" and communications stop intermittently. If I remove the jump from either preroute or postroute it

Hi I have Linux box (Debian) that acting as a bridge. Eth0 and Eth1 are bridged (br0). Br0 have public IP. Eth0 connects to the internet. Eth1 connect to servers in DMZ (with public IPs). Eth2 connects my Lan (192.168.1.0/24). My connections is 2Mbit/2Mbit. I''m doing SNAT for my Lan. QoS on eth0 works fine for DMZ, but is there a possibility to doing QoS on

Hi I have a small lan (10.0.0.0/8) behind my linux box. I use MASQUERADE to allow users connects to internet. I set up an esfq qdisc for outgoing traffic. And there is a little question. Does source hash type in esfq recognize NATed local ip''s? -- Pozdrawiam Marcin mailto:slacklist@op.pl _______________________________________________ LARTC mailing

Hi, i am running imq + htb on my router , the situation is like this eth0 = uplink to my provider eth1 = 1st customer eth2 = 2nd customer eth3 = 3th customer eth0 has limit 512 and i want to share this between eth1 eth2 and eth3 , but not working , this is the script i used, \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ #!/bin/sh

Hello, Some time ago I''ve read somewhere that local traffic in IMQ could hung up the whole system but it was corrected long time ago. So I was very surprised yesterday when it occurred not true. While testing IMQ I''ve observed for some time that - if you tag some local traffic with iptables both in pre- and postrouting - kernel is hunging up. It is happening quite quick with

Hello, I''m trying to get my shaper to work, but have only a partial success. Can someone help me with that. My setup unfortunately is not so trivial, but I think some people could have similar one... 1. There is a router connected to the internet line via interface eth0 2. There are users connected to the router via two interfaces : eth1 and wlan0 3. All users are assigned private IP

Hello, I wrote a simple traffic shaping script (below) that should have allowed me to shape my internet traffic a bit (ppp0 - adsl 128kbit/64kbit; local interface eth0). The script works only partially - the speed is being limited but too much. Without running this script my download rate is about 10kBytes (with second computer also downloading at about 6kBytes). After running it my download speed

Hi! I have read all informations i could find, but some things are still not clear. My setup is: ---INTERNET1(eth0)-\ /- Local net1 (eth2) GW ---INTERNET2(eth1)-/ \- Local net2 (eth3) I have NAT and a working setup using HTB,SFQ, classifying with the iptables -j CLASSIFY way. I shape only the traffic coming from the internet heading to the intranet. I would like

Hi I share my bandwith (adsl 512/128) between 12 users. I set up simple qos script for incoming (IMQ) and outgoing traffic using htb in root, 4 classess and esfq qdisc at leafs. Interactive traffic goeas to class1 , http,mail etc. to class2, p2p, ftp to class3, and rest to class4. Classess divide link in proportion 20% (prio 1), 40% (prio 2), 20% (prio 3) ,20% (prio 4) This works

Hello, I have eth0 - internet eth1..4 - local networks on eth0 i do $IPTABLES -A POSTROUTING -t nat -o eth0 -j MASQUERADE I want to balance out/in load for eth1..4 and localhost (mainly squid). Nat makes impossible to do it on eth0, so I installed IMQ. I need to get to on imq0 unnnated in/out traffic that I could make priorities for protocols and networks. Do somthing like this: prate=1Mbit