similar to: Shaping weirdness

Hi folks, I read the fantastic LARTC How-to and after that i tried to limit one host in my LAN for both down-and upload bandwidth usage. I took section 15.9. and added uplink-limiting as I understood it from the previous chapters. Unfortunately it doesn''t work. I ran the script and went to the specified PC, started a download, and watched the rate. The rate was always about 2000 kbit/s,

I have a setup where I have three NIC in a Debian box. I have eth1 conected to internet and eth0 NAT''ed to 192.168.1.1. eth1 and eth2 are bridged together, given ip 192.168.122.2. What I want to achieve is to perform traffic shaping on the bridge as well as prioritizing the traffic from eth0 very low. (This is from trental flat ...) However it seems that I am unable to perform thhe

Hi all, I''m having some problems setting up qdiscs on a bridge.The config looks a little like this: ifconfig ifb0 up # Bring up the IFB for this bridge. tc qdisc add dev eth2 ingress tc qdisc add dev eth3 ingress tc qdisc add dev ifb0 root handle 1:0 cbq bandwidth 100Mbit avpkt 1000 cell 8 # Raw qdiscs on each bridge port tc qdisc add dev eth2 root handle 1:0 cbq bandwidth

Hi all, I have installed 2.4.5 kernel, Debian Potato. my tc script: #!/bin/bash tc qdisc add dev eth1 root handle 20: cbq bandwidth 10Mbit avpkt 1000 echo root tc class add dev eth1 parent 20:0 classid 20:1 cbq bandwidth 10Mbit rate \ 10Mbit allot 1514 weight 1Mbit prio 8 maxburst 20 avpkt 1000 echo class tc class add dev eth1 parent 20:1 classid 20:100 cbq bandwidth 10Mbit rate \ 5Mbit allot

Hi everyone, This is on a linux box, ingress (eth1) at 100Mb/s and egress (eth0) at 10Mb/s. The purpose is to test CBQ Here is my script ------------------------------------------------------------------- # Root qdisc tc qdisc add dev eth0 root handle 1:0 cbq bandwidth 9Mbit \ avpkt 1000 cell 8 # Classes tc class add dev eth0 parent 1:0 classid 1:1 cbq bandwidth 9Mbit \ rate 5Mbit weight

Hello, I''m using tc to limit the bandwidth of our wireless customers. I have a working script, but I''m not happy with it. I''m trying to write a more sophisticated script, but when I run it, it give me this error: RTNETLINK answers: File exists I have no idea what this error means or how to fix it. Here is a portion of the script (the whole script shapes several

Hi,All I am using iproute2 to manage bandwith for ADSL router.High,medium,low priority are needed for different protocol port on the ADSL's upstream side,as following: LAN --- |ADSL Router|------WAN When there aren't traffic on the specific priority, its bandwidth should be borrowed by other priorities.But it doesn't work.Here is my script: /usr/sbin/tc qdisc del dev nas0 root

here''s the output : # tc -s -d class show dev eth0 class cbq 1: root rate 10Mbit cell 8b (bounded,isolated) prio no-transmit/8 weight 10Mbit allot 1514b level 2 ewma 5 avpkt 1000b maxidle 23us Sent 294 bytes 7 pkts (dropped 0, overlimits 0) borrowed 0 overactions 0 avgidle 605 undertime 0 class cbq 1:10 parent 1:1 leaf 10: rate 100Kbit cell 8b prio 1/1 weight 100Kbit allot 1600b

Hi, In my LAN Iam trying to make following setup: - All the traffic generated by 10.0.2.1 should go to 10.0.2.11, If the destination of this traffic is internet than it should be placed on its interface eth1. Outgoing traffic on eth1 should be shaped.For this I am using fw filters and cbq. _______ 10.0.2.1 -------> 10.0.2.11(eth0 )----| A

I am using a server with asterisk and I am trying to prioritize voip traffick -- I am a newbie at this traffic shaping, so please bear with me. I used the script below and what happens is thatall traffic in the bulk class stops after a couple of minutes. Also, should I include the ports for rtp in the filter statements with the ports 5061 and 4569? Note I have a fairly big pipe -- supposed to

Dear members I''m new to this list and also new to tc command. I have a subnet with over 30 pc which have ip addresses from 172.16.1.1/16 range.I want that each computer in my subnet can work with internet with maximum 6k for download and maximum 6k for upload.when i run the following tc commands from my bridge the first pc works well but the second pc can not work with 6k and it has an

Hi, I managed to fix 128kbit for an IP address of 192.168.200.3 as below: - tc qdisc add dev eth3 root handle 1: cbq avpkt 1000 bandwidth 100mbit tc class add dev eth3 parent 1: classid 1:1 cbq rate 128kbit allot 1500 prio 5 bounded isolated tc filter add dev eth3 parent 1: protocol ip prio 16 u32 match ip dst 192.168.200.3 flowid 1:1 tc qdisc add dev eth3 parent 1:1 sfq perturb 10 How can I

Hi All, I found 2 unusual behavior with u32 classifier in Kernel 2.4.12. I’ve u32 compiled as module. 1> u32 filter seems not working if there is already some fw filter used for some other class. In order to get u32 working I’ve to delete root class, which in terms delete all fw filters too, and then same command for u32 works. fw is also compiled as module. 2> If I add u32 filter to my

Hi All, I''m using iptables-1.2.7a on RedHat8 kernel 2.4.20. I wanted to limit the file-sharing traffic to the internet. I marked the packets with iptables: iptables -A FORWARD -t mangle -p tcp -s 192.168.1.1/24 -d ! 192.168.1.1/24 --dport 1024:1862 -j MARK --set-mark 1 iptables -A FORWARD -t mangle -p tcp -s 192.168.1.1/24 -d ! 192.168.1.1/24 --dport 1864:65535 -j MARK --set-mark 1

hi all, Iam using the following CBQs to limit the FTP bandwidth pease tell what changes are rquired to make it work.... tc qdisc del dev eth0 root tc qdisc add dev eth0 root handle 1:0 cbq allot 1514 avpkt 1000 bandwidth 100Mbit tc class add dev eth0 parent 1:0 classid 1:1 cbq allot 1514 bandwidth 100Mbit rate .4Mbit weight .4 prio 2 maxburst 20 cell 8 avpkt 1000 tc class add dev eth0

Good afternoon, I am a newbie to lartc. I have read the HOWTO. I set up a CBQ traffic control using the following commands, and it caused my VNC connection to break frequently. ======================================================================= **CBQ: cbq-1280.My_shaper /sbin/tc qdisc del dev lo root /sbin/tc qdisc add dev lo root handle 1 cbq bandwidth 20Mbps avpkt 1000 cell 8 /sbin/tc

Hi All , My first message and I have a little problem with my FC6 box trying to block emule traffic using layer7 . Here my network : Internet --------- ADSL Router ------------------- FC6 Box -------------------- Emule Box external ADSL : Dynamic Internal ADSL : 192.168.254.1 external FC6 : 192.168.254.3 internal FC6 : 192.168.253.1 Emule Box : 192.168.253.3 I guess that everything

Hi All, I''m trying to do some traffic shaping on an ethernet bridge. Currently, I have the following setup working: ifconfig eth0 down brctl addbr br0 brctl addif br0 eth0 brctl addif br0 eth1 brctl stp br0 off ifconfig eth0 0.0.0.0 up ifconfig eth1 0.0.0.0 up ifconfig br0 up This creates a bridge consisting of eth0 and eth1. So far so good. I now want to use tc to shape traffic

Hello everyone, I''m a newbie experimenting with CBQ shaping and am facing a few problems. Can any of you please help? TEST SETUP: +---------------+ +----------------+ | 10.0.0.103 |----------->| 10.0.0.102 | +---------------+ +----------------+ 10.0.0.103: Linux, 100Mbit/s NIC 10.0.0.102: Windows, 100Mbit/s NIC, iperf tcp server (ports 2000 and 2001) WHAT I

Hi, I''m trying to modify the Wondershaper script so achieve the following. 1. Prioritize traffic to the few IP addresses. 2. Everyone else should get a fair amount of bandwidth The problem I am facing is when I run this script is that the bandwidth seems to get halved. I tried to apply this script to a site where the upstream and downstream were fully saturated. I immediately saw