similar to: qdisc statistics

With the below script, whenever I ping 10.0.16.10 (which matches the only filter I have), traffic still get''s sent to the default 1:2 class instead of 1:1 and I don''t know why... Any hints? (kernel 2.6.12, iproute2-2.6.15) tc qdisc del dev eth0 root > /dev/null 2>&1 tc qdisc add dev eth0 handle 1: root htb default 2 tc class add dev eth0 classid 1:1 parent 1: htb rate

Andreas, Since I understand your ASCII art and comments, I would very much appreciate it if you would draw what you see and criticize the following. Hopefully I''ll better understand after that! TIA, gypsy tc qdisc add dev imq0 root handle 1: htb default 20 tc class add dev imq0 parent 1: classid 1:2 htb rate 4522kbit ceil \ 4760kbit burst 16k cburst 16k quantum 1500 tc class add

Martin Devera wrote: > If you read the manual, the algorithm will not work correctly > with {,c}burst < MTU ... > devik > I just tried to change {,c}burst to 1600, or leaving them by default but no visible result. here is the latest tc -s -d class show dev eth0 class htb 1:101 parent 1:1 prio 0 rate 40Kbit ceil 40Kbit burst 1599b/8 mpu 0b cburst 1599b/8 mpu 0b quantum 512 level

Hi, I''m fighting seriously with a most simple HTB setup. I''d like to share the incoming 64kbps into 5 and 59 for two different machines under NAT. HTB seems to hold the required limits when ceil is not set (no borrowing), but when borrowing enabled it seems to share equally rather then keeping the specified ratio. My setup is below. A typical output of "tc -s -d qdisc

Hello, I use HTB with linux-2.4.20-ac1 and iptables-1.2.7a (pathced for IMQ). I configured one HTB qdisc on an IMQ device. This qdisc has some classes (about 5) and all of the classes has qdisc pfifo. I sometimes got out from my linux (while I was working) and I found in logs: Dec 4 11:49:27 core kernel: HTB init, kernel part version 3.7 Dec 4 11:49:28 core kernel: HTB: quantum of class

tc qdisc add dev eth0 root handle 1: htb default 12 tc class add dev eth0 parent 1: classid 1:10 rate 30kbps ceil 100kbps burst 2k tc class add dev eth0 parent 1: classid 1:11 rate 10kbps ceil 100kbps burst 2k tc class add dev eth0 parent 1: classid 1:12 rate 60kbps ceil 100kbps burst 2k tc filter add dev eth0 protocol ip parent 1:0 prio 1 u32 match ip src 172.16.11.2 flowid 1:10 i login

Hi, I have a default class for my un-marked traffic (prio 5) and a prio 0 class for the important stuff, but I do not understand why my download traffic is duplicated in both. It work fine for my upload traffic (same setting except the red class but I have the same result if I create an esfq instead). Any comments/information will be appreciated. Below my config : tc commands from my scirpt :

Hi, there is something I''m not able to understand about HTB statistics. Why the qdisc show show how many packets are overlimits but in the classes there are always 0 packets overlimits or dropped? I try to expain with a simple example. I create a qdisc htb with only a class and then i do a lot of traffic. pc-innocenti:~# tc qdisc add dev eth0 parent root handle 1: htb default 10

Dear All, I''m using the kernel 2.6.6, iproute2-2.4.7.20020116, iptables v1.2.9, and gentoo. I have a leased-line 64 kbps. I can see the counter works in iptables, but in the htb, it doesn''t go to the right class (it always go to the default class). Any help will be appreciated here''s my htb conf #!/bin/bash tc qdisc del dev eth1 root tc qdisc add dev eth1 root

Running "tc -s class show dev eth1" against an HTB qdisc results in the output of class summaries similar to this: class htb 1:10 parent 1:1 leaf 10: prio 0 rate 150000bit ceil 1466Kbit burst 2Kb cburst 2Kb Sent 158641651 bytes 771351 pkt (dropped 0, overlimits 0 requeues 0) rate 8064bit 7pps backlog 0b 0p requeues 0 lended: 680985 borrowed: 90366 giants: 0 tokens: 173443 ctokens:

Hi! I''m trying to limit the uplink bandwidth using htb but no packets are overlimit or dropped. :-( My router config: * Linux kernel 2.4.20-pre10 (htb v3.7) with everything built as modules in QoS, iptables in use. * tc binary from htb3.6-020525.tgz * external interface eth0: Internet access, 512 kbit/s uplink speed * internal interface eth1: internal LAN, 100 Mbit/s The hosts in the

Hi, What exactly are the "tokens"? I thought each token allowed the sending of one byte, that tokens are stored in a bucket that can hold a max of "burst" tokens, and that this bucket is filled with tokens at "rate". But theory does not seem to explain the "tc -s .." output in the examples below. And I can''t figure out why or how... #tc qdisc

Hi All, I am using the script below to limit download rates and manage traffic for a certain IP address and testing the results using iperf. The rate that iperf reports is much higher than the rate I have configured for the HTB qdisc. It''s probably just some newbie trap that''s messing things up but I''m buggered if I can see it. The following script is run on the

Hi I have setup iproute2 and need a bit of help reading the stats from it ===== output qdisc htb 1: r2q 10 default 20 direct_packets_stat 0 ver 3.17 Sent 547326809 bytes 1342627 pkts (dropped 9303, overlimits 2817572 requeues 0) backlog 46p qdisc sfq 10: limit 128p quantum 1514b flows 128/1024 perturb 10sec Sent 41874343 bytes 730889 pkts (dropped 0, overlimits 0 requeues 0) qdisc sfq

Hi, machine: AMD K6 200 MHz Linux distribution: Mandrake 8.1 kernel: compiled 2.4.21 applied this: #define PSCHED_CLOCK_SOURCE PSCHED_CPU in file linux/include/net/pkt_sched.h bevore compiled the kernel (described on http://www.docum.org/stef.coene/qos/faq/cache/40.html) bandwitch on eth0: 128kbit The most simple configuration - 122kbit guaranted for WWW (sport 80) and

Eric, I''ve attached the output from the command you requested below. I''m using kernel 2.6.17.12 and tc version ss060323. I''m have a nforce4 onboard giggabit controller using the forcedeth driver, if that makes a difference. Charlie, I''ll take a look at the Apache model for throttling, thanks. I was going for tc because was going to try to add additional

i am trying to do some traffic classification using the PRIO qdisc and i am having a few problems. I have a root htb class: tc qdisc add dev imq0 root handle 1: htb default 255 r2q 1 tc class add dev imq0 parent 1: classid 1:1 htb rate 768kbit and a child PRIO tc class add dev imq0 parent 1:1 classid 1:99 htb rate 96kbit ceil 600kbit prio 0 tc qdisc add dev imq0 parent 1:99 prio tc filter

We run a Hosting farm behind a bridge/iptables firewall setup running Gentoo with kernel 2.4.20-gentoo-r6, connected to a dual 15Mbps international internet pipe / , as this: Net Pipe --------- eth1 Bridge/Firewall eth0 -------- Internal Hosting Network lately we have been looking at htb to somehow control excessive usage from the users behind, but in our implementation there seems to be an

How to do ensure a class not lended and not borrowed each other. I do cburst burst 0b ,but ctokens tokens go to negative! --------------------------------- Do You Yahoo!? "更多惊喜，同样精彩，NetVista A30 热卖" --0-611462377-1048485942=:33792 Content-Type: text/html; charset=gb2312 Content-Transfer-Encoding: 8bit <P>How to do ensure a class not lended and not borrowed each

I have this: class htb 1:29 parent 1:1 prio 0 rate 3000bit ceil 100000bit burst 1599b cburst 1611b Sent 33233 bytes 772 pkts (dropped 0, overlimits 0) lended: 415 borrowed: 357 giants: 0 tokens: -3756376 ctokens: 128779 or this: class htb 1:21 parent 1:1 prio 0 rate 3000bit ceil 100000bit burst 1599b cburst 1611b Sent 57554 bytes 618 pkts (dropped 0, overlimits 0) lended: 193 borrowed: 425