similar to: load balancing over multiple ISP links

I have 2 ADSL ad1 and ad2 , one PC for my firewall and some deamon on it with 3 ethernet : eth0 connect to my LAN ( 192.168.60.0/24 ) and 2 other connect to ad1 and ad2 |eth1 (10.0.1.2)--------------------ad1 ( ADSL 1 ) | My LAN(192.168.60.0/24) |---------eth0( 192.168.60.2)--> PC | |eth2 (10.0.2.2)---------------------ad2 (ADSL 2 ) All computer in LAN has default router =

Hi, A friend of mine has 2 lines of 512kbps terminated in two Linux boxes. He now want to remove those 2 boxes and have some device which will loadbalance the two ISPs and also have a failover arrangement. But he has agreed to give me a chance to do it on Linux for my own satisfication. Is this easy to do with lartc? How do I go about it exactly? I have very less time to do it since his

here''s the setup (two dsl - same provider) +-----> link1 LAN----- linux box --| |----------internet +-----> link2 the setup is ok in terms of the failover requirement. the other link takes over when one is down. however, there is a very noticeable lag when both lines are up. i''ve tried changing

hi, question. i was reading the howto, and the part about load balancing talk about to providers, well i have one provider and make to dial-modem conection, so i have the same gateway in both (ppp0 and ppp1) but to diferent IP. what do i have to do? just set up the default route to be a multipath route? or do i need to split the access? _______________________________________________ LARTC

Hi, I am connected to two DSL providers (DSL 1 - 1Mbps downlink/384kbps uplink and DSL 2 - 2Mbps downlink/512kpbs uplink) I would like to only allow ftp, pop3 and http via the DSL 1 and only smtp, ipsec and pptp via DSL 2. How can I do so? Can I use iproute to route these protocols? Below is my ip routing: - # DSL 1 ip route add 2.2.2.208/30 dev eth0 src 2.2.2.210 table 1 ip route add

Hi, I have the my gateway with load balancing traffic going out over two providers. Web browsing is fine...working great. But, my clients (office staff) complains that MSN keeps disconnecting (in 5 mins). Why? Please help me... Regards, ro0ot

Dear Sir, Please help me in building the right solution. My requirement is: 1st I want to club both ISP bandwidth to get 512kbps. 2nd, In normal condition, it should be in Load balancing. 3rd , In ISP Failover condition, traffic will automatically route to working ISP. What I have: I have installed the RHEL 3.0 with 3 Network Card. Kernel is 2.4.21-9EL I have the link from two ISP both

hi for those who was fallowing this topic I can say that IP_ROUTE_MULTIPATH_CACHED must be disabled! After few tests I''m quite sure that this was cousing my problems. Now I''m using 2.5.15 kernel without patch of Julian Anastasov and load-balancing is working. lartc split-access how to and http://www.ssi.bg/~ja/nano.txt now both are working fine Now I will try to use fwmark

I have three ADSL lines that I''d like to use as one big pipe to the internet. The ADSL service works by establishing a pppoe connection (the ADSL "modem" is a bridge), and each pppoe interface gets its own IP address. This means I''d have to have 4 ethernet interfaces (3 for each of the ADSL modems and 1 for the LAN) in my gateway. I''d setup the gateway to NAT

Hello, I have finished setting up the load balancer with IPROUTE ... also patch the kernel to support DGD and now it''s working fine with the valuable guide at LARTC website, Julian Anastasov, and the kind people in this mailing list. Now I would like to launch a web server and a ftp server to the public but I''m stuck into a problem and really need your help. Currently internal

--------------eth0---80.48.56.70---------- -------------80.48.56.65 ISP | my | router1 | | | linux | | | router2 ------------eth1---192.168.200.10----- ----------------192.168.1.1 ISP I''ve two ip from my isp one public and one internal. ISP have two routers router1 is gw for public ip and router2 is gw for internal

hi all, i am setting up a load balancing netwrok with failover, i have applied julian patch, but whenever i try to traceroute from any client node, it gives me two entries for that destination, but i get different interface for that entries, so it doesn''t forward my requests, i have done masquerading for client nodes, the ip rule/route are as follows, ip rule add prio 222 table

Hello all, I need a very simple routing protocol for VPN redundancy. We have several sites and each site has a Linux router and two IPCops each with an ADSL connection to the internet using different ISP''s. I have configured VPN''s between all of the sites for each IPcop on ispA and the same for the IPCops on ispB. This way, if one of the ISP fails, I change the route on the

Hello, On Mon, 17 May 2004, Charles-Etienne.Dube wrote: > I did some tests with 2 cable modems, but now it is installed in a production > environment with 4 cable modems. At first, everything seemed to work fine.. > But now I had a couple of users tell me that some web pages were > not available while others were, and it semms to be a masquerading problem > since when I

First of all i wanna thanks Christoph Simon for the support. Only after his reply to my email i could see the real solution to the problem (Valeu mesmo cara... me ajudou pra caramba! Fico te devendo essa!) :) Here is what i learned in a month of research: I tried A LOT of things to do load balance, including the one at LARTC homepage. The only tutorial that REALLY works in my case is the

Hello, I have configured a load balancing router using Julian''s patches and as described in "nano.txt" for two ISP links as shown below. ISP 1 ISP 2 . . | | | | | | | WAN

Hi! I''m studying load balancing and fault tolerance using multiple WAN interfaces. I follow the howto in http://www.ssi.bg/~ja/nano.txt but the problem is that faults detected are limited only in link between lan gateway and modem/router adsl, and none about adsl signal. Someone can tell me another howto about fault tolerance using a different method? (that solve my problem) I know

Dear List. I try to build multipath connection w/ load balance to internet with two different gateway; My system is RH-8.0 with iproute-2.4.7-7.90.1.rpm and Kernel-2.4.26 (patching with Julian A. patch),and follow guide from http://www.linuxvirtualserver.org/~julian/nano.txt, The problem is; when i try to connect to Internet form gateway machine it;s success , but only one interface is

Hi guys; I''m sure you are all bored of hearing the same story over and over... but here it comes again. :) Yep, tomorrow I''m getting another ADSL line installed and I wanted my linux router to handle both providers (new and old). I have my linux router (fedora core 2) setup to do NAT for my current line, but I know I''ll need to change my configuration to

I''m sure that I had found (and printed out ...) a really good tutorial that explain how to use Julian Anastasov''s routing patch, but I can''t seem to find it now. Any pointers? -- ****************************************************************** Glen W. Mabey Glen.Mabey@usu.edu http://mabeys.homelinux.com/glen/