similar to: how to add burstable rate?

Hi all, I''m having some problems setting up qdiscs on a bridge.The config looks a little like this: ifconfig ifb0 up # Bring up the IFB for this bridge. tc qdisc add dev eth2 ingress tc qdisc add dev eth3 ingress tc qdisc add dev ifb0 root handle 1:0 cbq bandwidth 100Mbit avpkt 1000 cell 8 # Raw qdiscs on each bridge port tc qdisc add dev eth2 root handle 1:0 cbq bandwidth

Hi all, I am running Slackware 10.1 with Kernel 2.6.14.3 includes iptables 1.3.4 with layer 7 My network diagram below: - INTERNET --- LINUX_ROUTER_FW --- PCs Below is my simple iptables script: - echo 1 > /proc/sys/net/ipv4/ip_forward iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE iptables -t mangle -A POSTROUTING -m layer7 --l7proto applejuice -j MARK --set-mark 1 iptables -t

Hi All , My first message and I have a little problem with my FC6 box trying to block emule traffic using layer7 . Here my network : Internet --------- ADSL Router ------------------- FC6 Box -------------------- Emule Box external ADSL : Dynamic Internal ADSL : 192.168.254.1 external FC6 : 192.168.254.3 internal FC6 : 192.168.253.1 Emule Box : 192.168.253.3 I guess that everything

OK, finally I have made cbq run ! now I would like to know if it is posible to limit a range of IP to a speed. something like this : from 192.168.1.1 to 192.168.1.21 limit to 128K I don''t whant to limit each IP to 128K, what I would like to do is limit all 20 IP to have a max of 128K. Is it posible?

Hey all, I had asked a question a little while ago about CPU usage being outrageous while using tc and a cbq qdisc. Ed was very kind and offered a few suggestions. One of these was to look at hashing. So after pounding away at it for about a week, I have a general understanding of how it works and have tried to implement it. Unfortunately, and quite obviously since I''m posting here, it

Hi All, I''m trying to do some traffic shaping on an ethernet bridge. Currently, I have the following setup working: ifconfig eth0 down brctl addbr br0 brctl addif br0 eth0 brctl addif br0 eth1 brctl stp br0 off ifconfig eth0 0.0.0.0 up ifconfig eth1 0.0.0.0 up ifconfig br0 up This creates a bridge consisting of eth0 and eth1. So far so good. I now want to use tc to shape traffic

Hello, I''m using tc to limit the bandwidth of our wireless customers. I have a working script, but I''m not happy with it. I''m trying to write a more sophisticated script, but when I run it, it give me this error: RTNETLINK answers: File exists I have no idea what this error means or how to fix it. Here is a portion of the script (the whole script shapes several

Hi everyone, This is on a linux box, ingress (eth1) at 100Mb/s and egress (eth0) at 10Mb/s. The purpose is to test CBQ Here is my script ------------------------------------------------------------------- # Root qdisc tc qdisc add dev eth0 root handle 1:0 cbq bandwidth 9Mbit \ avpkt 1000 cell 8 # Classes tc class add dev eth0 parent 1:0 classid 1:1 cbq bandwidth 9Mbit \ rate 5Mbit weight

Hi all, I have installed 2.4.5 kernel, Debian Potato. my tc script: #!/bin/bash tc qdisc add dev eth1 root handle 20: cbq bandwidth 10Mbit avpkt 1000 echo root tc class add dev eth1 parent 20:0 classid 20:1 cbq bandwidth 10Mbit rate \ 10Mbit allot 1514 weight 1Mbit prio 8 maxburst 20 avpkt 1000 echo class tc class add dev eth1 parent 20:1 classid 20:100 cbq bandwidth 10Mbit rate \ 5Mbit allot

Hi All, I''m using iptables-1.2.7a on RedHat8 kernel 2.4.20. I wanted to limit the file-sharing traffic to the internet. I marked the packets with iptables: iptables -A FORWARD -t mangle -p tcp -s 192.168.1.1/24 -d ! 192.168.1.1/24 --dport 1024:1862 -j MARK --set-mark 1 iptables -A FORWARD -t mangle -p tcp -s 192.168.1.1/24 -d ! 192.168.1.1/24 --dport 1864:65535 -j MARK --set-mark 1

Dear members I''m new to this list and also new to tc command. I have a subnet with over 30 pc which have ip addresses from 172.16.1.1/16 range.I want that each computer in my subnet can work with internet with maximum 6k for download and maximum 6k for upload.when i run the following tc commands from my bridge the first pc works well but the second pc can not work with 6k and it has an

Hi all, I''m having a hell of a time getting my IFB to work. I know I''ve done this before, so I''m missing something stupid. Can anybody tell me what it might be? Configs as follows: -------- #!/bin/sh modprobe ifb numifbs=1000 modprobe act_mirred modprobe 8021q brctl addbr br0 brctl setfd br0 0 brctl stp br0 off brctl addif br0 eth1 brctl addif br0 eth2 ifconfig eth1

I''ve been following the HOWTO, and reading mailing list discussions about throttling bandwidth, and have had some success, but I just want to tie off some loose ends. Essentially what I am wanting to do is to keep our bandwidth usage below 1megabit, because if we go over we get charged for that traffic. I''ve used some of the examples from the HOWTO to limit our bandwidth, but I

Hi, When i do ''wshaper start'' the interface i have defined stops routing traffic for some reason. It resumes routing when i do ''wshaper stop''. I''m using debian stable (3.0 woody) with debian''s default 2.4.18-686 kernel. When I run the script I get no errors, and when I do a ''status'', everything looks correct. Can ANYONE

Hi,All I am using iproute2 to manage bandwith for ADSL router.High,medium,low priority are needed for different protocol port on the ADSL's upstream side,as following: LAN --- |ADSL Router|------WAN When there aren't traffic on the specific priority, its bandwidth should be borrowed by other priorities.But it doesn't work.Here is my script: /usr/sbin/tc qdisc del dev nas0 root

Hi Folks, I''m using a 2.4.x kernel and TC from the iproute2 package so that I can limit traffic through my gateway. I''m using this to mark packets when they leave the LAN: /sbin/ipchains -A forward -j MASQ -i eth0 -s 192.168.1.0/24 -d 0.0.0.0/0 -m 1 When the packets return, I need to have them marked again so that the ingress filter will limit the bandwidth in the opposite

here''s the output : # tc -s -d class show dev eth0 class cbq 1: root rate 10Mbit cell 8b (bounded,isolated) prio no-transmit/8 weight 10Mbit allot 1514b level 2 ewma 5 avpkt 1000b maxidle 23us Sent 294 bytes 7 pkts (dropped 0, overlimits 0) borrowed 0 overactions 0 avgidle 605 undertime 0 class cbq 1:10 parent 1:1 leaf 10: rate 100Kbit cell 8b prio 1/1 weight 100Kbit allot 1600b

Hello, I am using the following commands to "throttle" the bandwidth of the NIC at eth0 : tc qdisc del dev eth0 root tc qdisc add dev eth0 root handle 10: cbq bandwidth 100mbit avpkt 1000 tc qdisc add dev eth0 root handle 10: htb tc class add dev eth0 parent 10: classid 10:1 cbq bandwidth 100mbit rate 128kbit allot 1514 maxburst 20 avpkt 1000 bounded prio 3 tc class add

I am using a server with asterisk and I am trying to prioritize voip traffick -- I am a newbie at this traffic shaping, so please bear with me. I used the script below and what happens is thatall traffic in the bulk class stops after a couple of minutes. Also, should I include the ports for rtp in the filter statements with the ports 5061 and 4569? Note I have a fairly big pipe -- supposed to

Hi all. I fear I''m slightly offtopic with this question, but I''ll keep it short: who is (or feels) responsible for the #lartc irc-channel in oftc.net? I''d appreciate if that person would get in contact with me (off-list) in order to discuss some ideas I have. Thanks in advance. Bye, Mike _______________________________________________ LARTC mailing list /