similar to: Load Balance Outbound AND Inbound Internet Traffic to one location over multiple links

First of all, I''d like to thank Andy Furniss for his direction and for helping me get a working example up and running. For the following set up to work, you will need a linux computer at the ISP (server), a linux computer at the client location (client), and some a public range of IP''s you plan to send down to your client. (as this configuration involves patching the linux

how to use iproute/iptables to balance by packet OUTBOUND traffic between 2 PPP (pptp cable modem and pppoe adsl modem) links to the same ISP . also by using the fact that the ISP dosen''t filter source IP address - meaning i can use either PPP''s link assigned IP address as the source IP in the ip header.., it works for both devices.., what i want to achive is : when uploading a

Hi,Andy Thank your very much! For the MLPPP LFI,I found that in Cisco configuration,it use "ppp multilink;ppp multilink fragmentation;ppp multilink fragment-delay 20;ppp multilink interleave " command to enable MLPPP LFI.So I think just realizing the same function on my linux router would be fine.But I got no idea how to do this on linux.So is there anything with iproute2?Would you

Hi There, We currently using iproute2 for load balancing. However we need more upload speed as we load balance over 3 dsl lines. I''ve been looking for a way to combine the upload speed to more faster. Found a site called www.upstreaminter.net where these guys bond the adsl channels to improve uploads, Since downloading is problem as its need to know the ip address of the downloader they

Hello, I am trying to make a load balance at my box using two conections. I have compile my kernel with this patch routes-2.6.13-12.diff (tha I get from this website: http://www.linuxvirtualserver.org/~julian/#routes). The problem is that when I try to balance using weight sintaxe (i will put the script bellow) some conectios just drop. So I can enter some pages but other I could not...

Hi list, I have tried google but just cant get this to work or figure it out. My setup ======== vanilla 2.6.13 kernel with CONFIG_IP_ROUTE_MULTIPATH=y CONFIG_IP_ROUTE_MULTIPATH_CACHED=y CONFIG_IP_ROUTE_MULTIPATH_RR=y CONFIG_IP_ROUTE_MULTIPATH_RANDOM=y CONFIG_IP_ROUTE_MULTIPATH_WRANDOM=y CONFIG_IP_ROUTE_MULTIPATH_DRR=y My configuration: A host with two ppp links. Ontop of these two ppp dialup

Hi, With kernel 2.4 I was able to use equalize to send our outgoing packets to two different routers (our isp supports this setup), like this: ip route add default src ip.a.dd.rr equalize nexthop via <router1> weight 1 nexthop via <router2> weight 1 The two routes were used equally on a per packet basis, not per flow or per cached route, but per packet, each line has 800k upload

Hello; we are looking to replace our current PBX with a *-box; it is connected to ONE ppp isdn connection that is terminated by the NC. We got on this box 4 msn's configured. currently we are working with pstn fxo's behind the PBX; it works but we can't use the CSID information behind it. We want to migrate and keep the MSN's to decide routing in combination with the CID.

https://bugzilla.netfilter.org/bugzilla/show_bug.cgi?id=512 ------- Additional Comments From kaber@trash.net 2006-09-18 07:36 MET ------- There are still some problems with the PPtP helper, I'm currently trying to fix these. Can you attach a tcpdump of a failed attempt please? -- Configure bugmail: https://bugzilla.netfilter.org/bugzilla/userprefs.cgi?tab=email ------- You are

Hi! Can I create the unnumbered GRE tunnel with iproute2 utility? Can someone provide me a link/howto/example_config how to do it? The topology is one tunnel between two linux boxes: -- eth1-|__|-eth0 <-------------> eth0-|__|-eth1 -- I''m trying now with: ip tu add tun1 mode gre local loc.IP remote rem.IP ttl 255 dev eth0 ip addr add tun1 0.0.0.0 ip link set tun1 up but it

Hello all, I am configuring a vpn between freeswan and windows 2000. I am following the steps at http://www.jacco2.dds.nl/networking/win2000xp-freeswan.html, to get the VPN up and running. using this I have a ppp tunnel between windows and linux, which is inside a l2tp tunnel which is again encrypted by IPSec. (the url gives the configuration in detail and I have followed it exactly) Now the

Hello Lartc Mailing List: Been working on something the last week and a half and ALMOST have it working.., just need a few pointers from the wizards on this mailing list to nail it. Ok, my setup is a hub and spoke arrangement, hub is Cisco 2821 with IOS 12.4. Spokes are ruggencom RX1000 routers, Debian based with the following versions installed: rx1000test:~# uname -a Linux rx1000test

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I have a situation where some Poptop/PPTP sessions (only with FC5/Shorewall to FC5/Shorewall firewall in between) cause the following to appear in the state table (shorewall show connections). unknown 47 420 src=XX.234.79.183 dst=XX.234.137.226 packets=2 bytes=130 [UNREPLIED] src=XX.234.137.226 dst=XX.234.79.183 packets=0 bytes=0 mark=0 use=1

Hello I have /25 addressed on a box (virtual devices on eth0) and I want to tunnel some of these addresses to my home network. One address to my gateway (a.b.c.d, external IP) and one address to my internal network (192.168.0.0/24-style). I will use the tunnels for irc, smtp and surfing. What protocol and which technique is easiest and best to use? One more thing. I don''t want to set up

Hi all, This is probably not the right place for this question, but maybe someone can help me out. I am trying to setup a VPN between two private addresses, using iproute2 (which is my only excuse for mailing this list). The setup is as below : eth0 ppp0 Wireless ppp0 eth0

Hi, I have a very simple server setup, using shorewall as my firewall. I have a line like this at the top of my rules file to allow ssh connections, but limited to 3 connection per minute with a burst rate of 3: SSH/ACCEPT net $FW - - - - 3/min:3 - Now when I have that in place, and from a remote machine run scp server:/some/file ., I find

Greetings List Members, I''ll firstly apologise if this isn''t the place that I should be posting this message but here goes. What I want to do is have a VPN (PPTP/IPSEC/CIPE/etc) server, but it must support more than one simultaneous connection. I currently have a PPTP VPN server setup that has port 1723 and protocol 47 DNAT''d through to the internal IP

I always used multiple links from different ISPs and in my oppinion the best way to really aggregate bandwidth is using some kind of proxy which the client connects to and distribute multiple connections to the links. Years ago, a friend of mine wrote Netsplitter: http://www.hostname.org/netsplitter/ but it''s outdated, abandoned (last version from 2002). And it was mainly written for

Hi Not entirely centos related but that what the boxes are running so here i go ;) 2 of our centos boxes run nagios for network monitoring and send email and paging alerts and are connected to standard phone lines using modems to send the pages. I'm looking for a way in the event of provider failure to login to these machines and so am looking at the ability to connect to the console over

I am not sure if this is a windows problem or a Samba problem. We have a network consisting of a mixture of Samba and windows servers running under a windows PDC. The network is a WAN with radio (802.11B) point-to-point links between buildings within the campus, and frame relay and ADSL links to interstate offices. The interstate offices have windows BDC's. Most of the desktops are win2k