similar to: error making htb example

My previous message (http://mailman.ds9a.nl/pipermail/lartc/2004q2/012285.html) didn''t generate any replies, so I thought I''d try posting what I''ve done trying to solve my own problem, in hopes that someone will take pity and show me if/where I''m going wrong. Just to recap, I''m trying to accomplish this on my server, which streams RealAudio files

Hi all, Can someone please help with a tcng setup? I have played with tc and tcng in the past, and now would like to get some serious rules in place. However, I have a difficulty in setting them up. My setup is as follows: One machine working as a firewall: eth0 is the interface connected to a 512K DSL line eth1 is connected to a LAN eth2 is connected to another LAN, a bit like a DMZ eth1 and

Thank you for your help. It generates this script : tc qdisc add dev eth0 handle 1:0 root htb default 2 tc class add dev eth0 parent 1:0 classid 1:1 htb rate 75000bps ceil \ 75000bps tc class add dev eth0 parent 1:0 classid 1:2 htb rate 125000bps tc filter add dev eth0 parent 1:0 protocol all prio 1 u32 match u32 \ 0xa000001 0xffffffff at 12 classid 1:1 But I thought it was necessary to

Hi all, I have read the larc howto and I need to apply a traffic shaper with this configuration: router / two interface etho and eth1 lan lan is on eth1 and on eth0 I''ve the dsl connection (1.2 Mbit / 256 kbit) I need to limit the bandwith towards lan and I''ve thought at HTB and tcng. I write the script belove. I want limit the p2p and ftp (ssh and irc) connection at 15

Hi, I wanted to configure the following : 1. VPN + some other special connections (TCP 82,8282,23,22 and ICMP) to have priority over the rest 2. special upstream for our updating system on port 4000 3. within the VPN tunnels citrix traffic ( TCP 1494, 2598) + icmp has priority I need this for both incoming and outgoing traffic as it is the bandwith managment config on a central system from

Hello all, I am trying to set up a simple htb based system, where packets with source ip 10.0.0.1 should have their own class. I plan to use tcng to set it up easier. Is there something wrong in my tcng file ? ~/tcng$ cat htb /* */ #include "fields.tc" #include "ports.tc" dev eth0 { htb ( ) { class ( rate 600kbps, ceil 600kbps ) {

Hi I''m completely stuck with the tcng language - I assume there must be some way to arrange queues hierachically like eth1 | TBF | PRIO / \ class class but my attempt (below) produces a "inferno.tc:8: qdisc "tbf" has no classes near "prio"" when run through tcc. dev eth1 { egress { tbf (rate 128kbps, burst 64kb,

Hi, I am new to traffic control in linux. However, i have able to grab many new knowledge in recent days. I find tcng somewhat easy to use (although lack proper doc. of its usage). I want to control traffic of several IP Addresses connected to my LANSIDE. What I want is , i want to separate certain bandwidth to all my clients. dev "etho" { htb() { class ( rate 400kbps, ceil

Hello Mailing list, I have a problem with the prio qdisc and I don´t know what is wrong in my configuration This ist a sample configuration and looks like this: #include "fields.tc" #include "ports.tc" #define X16(i) i i i i i i i i i i i i i i i i dev ppp0 { dsmark { prio(bands 6, priomap X16($be)) { class if ip_proto == IPPROTO_UDP;

I can''t seem to match packets less than 512 bytes: class( <$bulk> ) if tcp_dport == 81 && !( ip_len & 0xfe00 ) ; or if tcp_dport == 81 && ip_len < 512 Both rules match any packet I send to port 81, even when the total IP length is much greater than 512 bytes: class htb 2:4 parent 2:1 leaf 5: prio 1 rate 8000bps ceil 24000bps burst 6Kb cburst 1839b Sent

Hi folks I have created a script file (dsmark+policing.sh attached) to check graphic an text outputs of simutations, against original examples/dsmark+policing coding (see TCNG Reference Manual-pg.90). It uses tcng coding (*.tcsim file attached) and old tc coding (*.tcsim_old file attached) inserted in tcsim files. Observation 1: The graphic outputs from (*.tc included in *.tcsim) and (*.tc_old

Hey all, i have a class. class ( <$call1> ) if ip_dst == 10.100.1.6 && tcp_dport == 22 if ip_src == 10.100.1.4 && tcp_sport == 22 ; Now when i apply this traffic TO 6 on port 22 is indeed limited to the speed i specify BUT it doesn''t seem to take the src into account at all. If i change the src to anything, even an address that

hi all, i''m having problems building a module from my tcng configuration file. could someone verify the syntax for building a kernel module? i did it as shown below ... module gets built but i cannot load it. thanks charles ps -- sorry, don''t know c++ :-) [root]# cat /etc/tcng.test #define LAN "eth0" #define LAN_INGRESS 750000 #define LAN_EGRESS 750000 dev

Greetings all, OK - just started playing around with traffic shaping - have imq and htb and (I think) everything else I need in the kernel and running well. My initial lab task was to protect a H.323 session over a simulated half T1 while adding bulk traffic - got that accomplished after slogging through learning tc and decided in short order that a more intuitive interface would be

Hi, I try to shape my incoming traffic. I have 2MBit/s DSL bandwith and the following ruleset (on the internal interface): $INT="eth1"; $INT_NET=192.168.1.0; $MAX_IN=2Mbps; dev $INT { egress { class (<$int>) if ip_src:24 == $INT_NET; class (<$ssh>) if tcp_sport == PORT_SSH; class (<$smtp>) if tcp_sport == PORT_SMTP; class (<$http>) if

Hello. I have been trying to duplicate these u32 matching rules using TCNG, but without much success: tc filter add dev eth0 protocol ip parent 1:0 prio 1 u32\ match ip protocol 6 0xff \ match u8 0x05 0x0f at 0 \ match u16 0x0000 0xffc0 at 2 \ match u8 0x10 0xff at 33 \ flowid 1:10 Wondershaper 1.1a implements this and if I run it things seem to be shaped as expected. But this TCNG

hi, i´am new in tcc (tcng). i try to define my qos for VoIP-Services. For this i wantto define a class for a port range 10000 till 15000. how is the right way? this down works: class (<$voip>) if tcp_sport => 10000 || tcp_sport <= 10000 ; are there any examples of real installations - maybe including VoIP, HTTP and P2P services? regards thorsten gehrig

Hi! I am learning tcng without having experiance of tc and I am trying to build something that shall schedule traffic dependent on the value in the IPv4 packets ip_ttl field. I have read the tcng reference manual and cannot find information about forwarding. Is it possible to farward packets from ingress to egress without sending them upwards in layers?

Hey people, I have the following tcng configuration: #include "fields.tc" #include "ports.tc" dev "eth0" { egress { // Voice traffic class (<$voice>) if udp_dport >= 20000 && udp_dport <= 23000; // SSH connections class (<$interactive>) if tcp_dport == PORT_SSH; //

Hi all, I have a little problem with my home-made slackware linux server. Here is the scenario: 1. I have a local wifi network 2. my server do masquerading and exit in internet via a PPPoE connection Goals: 1. not use SQUID 2. shaping the traffic with classes 3. emule connection must have minimum priority and a band-limit of 10KBytes/s in uplink (server--->internet) Any idea? Thx, Diego --