similar to: IP based bandwith limit

Hello, I have a serious problem with HTB which I wasn''t able to solve myself. I run a masquerading router with ppp0 as interface to the Internet. Three clients need to share a downstream of 1 MBit, which I want to divide with tc. When I see a packet being forwarded to one of these clients, I give it the appropriate unique mark: iptables -t mangle -A FORWARD -d 192.168.34.141 -j MARK

Hello all, I´ve read http://lartc.org/howto/ and now i am just confused, i think my skills with linux are not very good, so asking for help. I have a linux box with two ethernets cards eth0(gateway 1mb) with is the host for some sites and emails and eth1(nat interface) with provide internet acess to other 5 pcs. I would like to limit the bandwith 512 k for the eth0 and 512 k for eth1 however

Hi, Is there any tested good HTB script for traffic shaping available like as that of CBQ available at. http://freshmeat.net/projects/cbq.init I am n new bie and need to work on htb. -- Regards, M Arman _______________________________________________ LARTC mailing list LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

dear All, I'm a new student and my job is too shapping bandwith for our campus faculty network. I want to implement htb with Redhat-9.0 distro. does this distro kernel support htb and tc good ? or i should apply some patch or upgrade kernel ? regards reza

I have an htb qdisc setup and it is shaping my traffic wonderfully but I''ve just recently started taking a look at the output from the command tc -s class ls dev eth? Looking at the "rate" line I thought to myself..."cool I can use this to graph throughput avg.es without having to worry about the "Sent bytes" rolling over or being lost when the htb qdisc is

I have clients, which connectin to Internet through vpn. I want to dynamically share bandwith between vpn connections, so if there few connections, then they get all bandwith, if more then they get their minimal guaranteed bandwith. my idea is: ip-up.local: tc class add dev $DEV parent 1:1 classid 1:2${1/ppp/} htb rate $[$RATEUP/$VPNS]kbit ceil ${RATEUP}kbps tc filter add dev $DEV protocol ip

Hello, I''m trying to configure several wireless routers with QoS support. The idea is to implement differentiated services so that VoIP traffic gets the maximal priority, then video, control traffic, interactive data traffic and best-effort traffic. I have seen that CBQ used to be chosen as qdisc for implementing bandwith share in DiffServ but now HTB is preferred because it is

Hello, I just found the great howto and started shaping my internet connection. The howto''s last update is a liitle in the past now so I have some questions about how things are done the best way nowadays ;-) To ensure a stable and low latency voip communication I added an HFSC qdisc to device ppp0 (1 Mbit SDSL). There are two classes (by now): One for SIP and RTP and one for the

Hey list I have almost gotten my shaping setup up and running as planned. The last barrier seems to be tcp overshooting availible bandwidth when its starting a transfer, and thereby bursting the line, so ping rises for a moment. At least this is my best guess at the problem :) There is a possibility that its just plain old traffic being bursty for some reason.. I am using bittorrent to test this,

Hi all, I have read the larc howto and I need to apply a traffic shaper with this configuration: router / two interface etho and eth1 lan lan is on eth1 and on eth0 I''ve the dsl connection (1.2 Mbit / 256 kbit) I need to limit the bandwith towards lan and I''ve thought at HTB and tcng. I write the script belove. I want limit the p2p and ftp (ssh and irc) connection at 15

How to do ensure a class not lended and not borrowed each other. I do cburst burst 0b ,but ctokens tokens go to negative! --------------------------------- Do You Yahoo!? "更多惊喜，同样精彩，NetVista A30 热卖" --0-611462377-1048485942=:33792 Content-Type: text/html; charset=gb2312 Content-Transfer-Encoding: 8bit <P>How to do ensure a class not lended and not borrowed each

I have this problem: I have an Internet line input with variable speed. I have a max speed and a min speed: Vmax and Vmin. The speed is always changing between Vmax and Vmin. I want to share the actual bandwidth (you don''t not how much, you only know the speed is between Vmax and Vmin) for N clients. The bandwidth should be shared so nobody can get more bandwidth than the others.

Hi! I have just started with traffic shaping, and after hours of reading websites, man pages asf. I am still stumped at one problem I have. The interface eth0 is attached to the outside world, and I have an openvpn tunnel to another part of the organization using eth0 and port 5001. The idea was that all traffic going through the tunnel would have top priority and the rest share

Hi, The CBQ config file shud be some thing like this. DEVICE=eth0,10Mbit,1Mbit RATE=50Kbit WEIGHT=5Kbit Shall i hardcode the DEVICE BW as 10/100 Mbit or Shall i use any other tool like ethtool for getting this. ethtool gives Speed: 10Mbps If so, how about, if i use some other Interfaces other than eth0, like ppp0 or some other? C''d anybody can give a suggestion over this? thanks

Hi, I''m fighting seriously with a most simple HTB setup. I''d like to share the incoming 64kbps into 5 and 59 for two different machines under NAT. HTB seems to hold the required limits when ceil is not set (no borrowing), but when borrowing enabled it seems to share equally rather then keeping the specified ratio. My setup is below. A typical output of "tc -s -d qdisc

Hi, I found that I had some thinking error with the wshaper script. I assigned the bandwith of my DSL connection to it, but the machine where it runs is normally connected to the LAN with 100Mbit behind a separate Hardware-Router.Obviously, the complete connection of the machine was slowed down to 384k because I told it so.I guess, since wshaper takes only one card as argument, I can''t

Hi all! I''m trying to shape traffic in a dorm''s network (4 mbit symmetrical internet link, about 200 computers, heavy p2p usage). The router is a p4xeon running linux 2.6.9 with the qnet patches (http://kem.p.lodz.pl/~peter/qnet/). When I activate ip_forward I get >20% packet loss and a lot of duplicates. Any ideas? I attach my shaping script. Thank you very much in advance,

Hi all! I have a problem setting up HTB on my home network. I have a network: 192.168.1.0/24 and I want to limit the download to 200 KB to every IP from my city ( I have the IP''s of most ISPs). The thing is that I I want to limit the international traffic too (I do not use BGP) and set it to 15 KB. Can someone help with this setup? Thanks! Best regards, -- George -- This message

I am working on my Diploma Thesis on Computer Science Engineering. The main idea behind of my work is to make it possible to have a Linux box combining multiple ISP/network connections together providing a single connection with an aggregated bandwith. I have been surfing the Internet and I haven''t found anything like that running on Linux. I would like to implement it using iproute 2

Hello, I''m Alexandra Well, i have been working with cbq around 3 month ago without any problems, what i do is control the bandwith to 64Kbit for input and output and it works well. But now I don''t want control the Bandwith, i only need prioritize udp trafic over tcp trafic Can somebody to help me with my requirement? Thanks Alexandra