similar to: Shaping on Ports, multiple IP Address''s, and SFQ

Hi All, I''ve got an interoffice IPSEC VPN in place that I''m trying to give priority to terminal service (tcp 3389) traffic. I''ve created rules at each end, but have hit a bit of a dillemma. As the data is encrypted I must also give highest priority to protocol 50 otherwise the priority is lost as the packet gets encrypted. When I do this however, I can''t

Hello, I wrote a simple traffic shaping script (below) that should have allowed me to shape my internet traffic a bit (ppp0 - adsl 128kbit/64kbit; local interface eth0). The script works only partially - the speed is being limited but too much. Without running this script my download rate is about 10kBytes (with second computer also downloading at about 6kBytes). After running it my download speed

Hello, I''m trying to get lossless VoIP traffic over my 3000k/500k ADSL line. Shaping outgoing traffic is no problem: I set total ceil for outgiong device (ppp0) to 450kbit and put VoIP into highest prio class. Even during full upload the voice is clean on the other end. Now I tried to get the same result for incoming data. I attached HTB to eth1 where the incoming voip traffic is

Hi, I´m shaping traffic using htb on both interfaces, I noticed that shaping download traffic is workinggreat but shaping upload traffic is not working at all (no sent packets, no dropped, no overlimits)I have eth0 facing the backbone and eth1 facing the LAN. Thanks for your help.These are the commands I run:tc qdisc del dev eth0 root tc qdisc add dev eth0 root handle 1 htb default 10 r2q 5 tc

Greetings, I''ve got a server with a bunch of vpn (openvpn) tunnels terminating on it. I''m trying to limit the total bandwidth the tunnels can use to 3mbit. So I applied a rule like this: ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ tc qdisc add dev eth0 root handle 1: htb default 90 tc class add dev eth0 parent 1: classid 1:1 htb rate 100mbit burst 15k # Default rule for

Hello Shorewall users, I have some questions I am hoping someone can answer. I have searched around the archives but so far I have been unable to find answers. I am trying to configure traffic shaping on my router/firewall box running Shorewall 3.0.5/kernel 2.4.31 and have run into some problems/questions. My basic set up is: 1500/256kbit ADSL (PPPoE/ppp0) -> Shorewall box

Hi, I have tried unsuccesfully to limit my ftp server send speed in linux. I have an ipcop linux firewall/router with 2 nics. 1 nic (eth1) is connected to a 3mbit/384Kbit cable connection and the other (eth0) a switch. Behind it i have a suse linux box and a windows box. On the suse box i run proftpd. I need to shape my passive ftp send speed to 34KBytes because if it is maxed out at 45K

Please see below Jon Flechsenhaar Boeing WNW Team Network Services (714)-762-1231 202-E7 -----Original Message----- From: Flechsenhaar, Jon J Sent: Wednesday, September 27, 2006 9:35 AM To: lartc@mailman.ds9a.nl Subject: [LARTC] 2.6.14 - HTB/SFQ QoS broken? Jody: I don''t know if you answer basic HTB questions but I''l try anyway. I''m implementing AF and EF with a

If in one time 3 IP adresses using internet. TC script: DEV=eth0 # LAN SERVER_IP=192.168.1.2 # eth0 ip address tc qdisc add dev $DEV root handle 1: htb default 255 tc class add dev $DEV parent 1: classid 1:1 htb rate 384Kbit quantum 1500 tc class add dev $DEV parent 1:1 classid 1:20 htb rate 128Kbit ceil 384Kbit prio 0 quantum 1500 tc class add dev $DEV parent 1:1 classid 1:21 htb rate 128Kbit

Dear list, I have the problem that child classes don''t seem to issue the parent class to borrow from their parent. This is a simplified version of my script: tc qdisc del dev $DEV root tc qdisc add dev $DEV root handle 1: htb default 10 tc class add dev $DEV parent 1: classid 1:1 htb rate 10mbit tc class add dev $DEV parent 1:1 classid 1:10 htb rate 1kbit ceil 512kbit #groups tc

Hi, I''m trying to modify the Wondershaper script so achieve the following. 1. Prioritize traffic to the few IP addresses. 2. Everyone else should get a fair amount of bandwidth The problem I am facing is when I run this script is that the bandwidth seems to get halved. I tried to apply this script to a site where the upstream and downstream were fully saturated. I immediately saw

Hello! I have a small home network and I''d like to use traffic shaping because every time someone uploads a file at full speed, my download speed drops to ~10 KB/s. My connection is 768/128 DSL. I found a script at http://www.knowplace.org/shaper/examples.html $TC qdisc add dev $INTERFACE root handle 1: htb default 60 $TC class add dev $INTERFACE parent 1: classid 1:1 htb rate 116kbit

> > SFQ is very useful as a leaf qdisc. But by default, its internal queue > > length is 128 which is too much for small classes or even for > > not-so-fast links. Changing SFQ_DEPTH in net/sched/ sch_sfq.c to about > > 10-20 results in flows responding much faster to bandwidth changes. I''m not sure I understand what problem is being described, but I suspect

hi all: the following scipt is wokring perfectly with limiting ...on limimitng per ip basis.. ---- eth0=public static ip eth2= private ip ( 192.168.2.1) -- iptables -t mangle -A POSTROUTING -s ! 192.168.0.0/32 -d 192.168.2.101/32 -j MARK --set-mark 21012 tc class add dev eth2 parent 1:1 classid 1:2101 htb rate 32kbit ceil 64kbit tc filter add dev eth2 parent 1:0 protocol ip prio 2 handle

Hi to all I am studying HTB on LARTC how to. I realize a simple configuration on router: tc qdisc add dev eth0 root handle 1: htb default 30 tc class add dev eth0 parent 1: classid 1:1 htb rate 3mbit burst 15k tc class add dev eth0 parent 1:1 classid 1:10 htb rate 2mbit burst 15k tc class add dev eth0 parent 1:1 classid 1:20 htb rate 1mbit burst 15k tc qdisc add dev eth0 parent 1:10 handle 10: sfq

Ok, earlier I post a message explaining my problem with HTB and layer7 (or ipp2p), about not being able to shape the traffic. Well, actually this is what''s happening, I''m marking the packets (right now, I''m using ipp2p as Klaus adviced me to) with iptables, and my queue rules are made using tcng, I''m using the HTB qdisc, and traffic is going to the HTB class

hi who can ever help me out with the shaping of torrent traffic? i have a pptp at ppp0 over eth0 (10.0.0.1/8) i would like to shape outgoing traffic of rtorrent on these two interfaces, assume rtorrent is running at port 6999 need 3mbit for ppp0 and 50mbit for eth0 i supposed: [tcclasses] ppp0 1 2mbit 3mbit 1 eth0 2 20mbit 50mbit 2 [tcrules] 1 0.0.0.0/0 0.0.0.0/0 tcp

I''m grappling with a problem that looks like sfq is not working (packets don''t get fairly queued, they appear to be always sent FIFO). My configuration appears to be correct. The machine is running quite an old kernel and if I could convince myself that the sfq code it has is just broken, I''d spend the time to upgrade it. Is there any way to inspect or dump the sfq hash

Hello. I have just started using iproute2 commands, and I am having a go at making bittorrent use the same bandwidth for upload as for download. I am stuck I think in understanding speeds I connect to the internet through a router modem which gets the real IP and assigns me a private ip through dhcp. So this router can handle a private network, and route it to the internet, pressumably with nat.

Anyone notices that using sfq qdisc adds latency compared to pfifo? With "sfq perturb 10" ping latency is around 100-120ms, while with "pfifo limit 3" drops to ~10-30ms (qdiscs belong to htb class). I''m missing something or is this expected? { $TC_CLASS parent 1:1 classid 1:20 htb prio 0 rate 900kbit ceil 1000kbit burst 7k $TC_QDISC parent 1:20 handle 200: {pfifo