similar to: [Fwd: Re: ssh and cs LAG]

Displaying 20 results from an estimated 8000 matches similar to: "[Fwd: Re: ssh and cs LAG]"

2004 Oct 21
3
[Fwd: up and down shaping based on IP]
Hello, i have a server (486sx and 16ram). My pc is providing internet to 12 other computers. Ethernet cards are realteks 8139 (drivers builtin to the kernel 2.6.8). It gives me this error : NETDEVICE WATCHDOG eth1 : ...timeout. I checked in many places for solutions. Even wrote to this mailinglist. But lately i recived information, that too much upload may mix my adsl modem up. So..... my
2005 Dec 20
1
how to correctly turn off apic at boot
I have tried in the grub.conf file noapic and apic=off I am still getting the same error message about ACPI in the dmesg output. example: ACPI: PCI interupt .... IRQ 16 eth0: RealTek RTL8139 ... IRQ16 eth0: identified 8139 chip type so ACPI is grabbing IRQ 16 and not letting eth0 have it. (I Think). How do I correctly disable it on my compaq v2000 laptop. I think it is not allowing my usb
2007 Jul 05
1
unable to boot centos 5 on dell optiplex 320
Hello All. I have a dell optiplex 320 that I can install centos5 on using pci=nomsi. That seems to be the only way. After the install grub loads but thats about as far as it gets. It looks like a BIOS bug to me, but I just don't know. I left it sit for a few minutes and it just had the echoed boot params on the screen. I've tried booting with noapic nolapic apm=off acpi=off and noprobe
2004 Jul 01
14
filter ingress policy rates -> slow!!
Hello one more time, As others seem to already asked without reply, I''m getting lower speed rates than specified via ingress. How do I know. Because I have this in my script: tc qdisc add dev $DEV handle ffff: ingress # Filter intranet traffic, so fit it to intranet speed tc filter add dev $DEV parent ffff: protocol ip prio 10 u32 \ match ip src $Q_2_HOSTS \ match ip dst
2004 Oct 21
1
can''t understand howto example
tc class add dev $DEV parent 1: classid 1:1 htb rate ${UPLINK}kbit burst 6k tc qdisc add dev $DEV handle ffff: ingress tc filter add dev $DEV parent ffff: protocol ip prio 50 u32 match ip src \ 0.0.0.0/0 police rate ${DOWNLINK}kbit burst 10k drop flowid :1 why does the download is being sent to class 1 which is limited by uplink ? why the rate is being mentioned in filter and in class ?
2003 Mar 03
5
Re: 2.4.20 htb3 oops
Hi everyone, I am having problems with "oopses" since I introduced HTB on my company''s PC-based routers. It seems that only routers with high network load are affected. The average network load on the two most problematic routers are 10Mbps in/out and 2.5Mbps in/out. The other machines with less than 1Mbps average traffic seems unaffected. We have been getting oopses on
2006 Jan 15
9
even bandwith for users on 2 newtworks
Server : eth0 - internet DSL eth1 - LAN wlan0 - wireles LAN I want server to share bandwith from eth0 evenly for users on eth1 and wlan0. How can i make it ? Is it possible ? As far as i know htb splits outgoing bandwith on one device only. ---------------------------------------------------- Grypa? Damy radę! Sprawdź jak jej zapowbiegać, a jeśli już za późno ...jak leczyć - grypa.wp.pl
2004 Jun 02
7
Linux vs. Windows XP routing latency
Hello, I have a problem with the latency of the packets passing a Linux router, and I thought perhaps you could put some light on it. It''s quite simple. I have one ADSL connection, and a LAN. The gateway is the Linux machine or a Windows XP machine. When the wXP is routing, for a host inside the LAN, the latency of, for example, the Counter Strike game to a given server is around 20 to 30
2006 Feb 15
2
clock, centos 4 and dual core?
Hi, I have a dual core athlon server and it is gaining 1 day every 2 days w/o time sync. Even with ntpd running, the time is not under control. I must put a very frequent cronjob of 'ntpdate' to keep the time under control. This creates big problems since winbind eventually stops working so my users can't access their data. Any ideas? -- Ugo -> Please don't send a copy of
2004 Jan 06
7
Getting ext3 up and running
I have a Debian system from a Knoppix distribution. I started out with ext2 but decided to change to ext3. tune2fs -j OK. However the system boots with a warning ....ext3 mounted as ext2. proc/mounts confirms this and no journal is running. So I have to make an initrd. Did so using instructions in the Debian Reference and this did not change anything. Any attempt to use the img produced was a
2009 Aug 13
6
how to get R interpreter to remember constant values without using any memory location
Maybe I expect too much from a non compiled language. Anyway, I wonder whether it is possible in R to set constant values without using any memory location that would take useless space bacause such values are not going to be changed along the program. It's just a way to assign a mnemnic name tos some constant values. For instance, I would like R interpreter to replace all occurrences of
2015 Aug 12
4
Bug#795330: Suggests noapic but doesn't support it
Package: xen-hypervisor-4.5-amd64 Severity: normal Hi, when running xen inside of kvm the hypervisor fails to set up the proper IRQ routing and suggests to use noapic. If you add this via GRUB_CMDLINE_XEN_DEFAULT it will boot futher but then report that noapic isn't supported. So please make Xen not claim to support noapic if it doesn't (the issue was finally resolved by removeing
2004 Jan 13
3
RE: [OT] Re: Getting ext3 up and running
I referred to the entry rootfs / rootfs rw 0 0 in the output of "cat /proc/mounts", that is not really very much explicative, due to the setting "auto" in /etc/fstab and to the fact that file system had has_journal flag and no ext3 module was mounted. But I was wrong: I think that if you have an ext3 fs and you mount it as ext2, you continue to see the has_journal flag with
2005 Mar 11
4
(no subject)
--- Ryan Lane <ryanlane@gmail.com> wrote: > On Fri, 11 Mar 2005 07:21:39 -0800 (PST), Steven > Vishoot > <sir_funzone@yahoo.com> wrote: > > ok now i am frustrated. this is the third day in a > row > > that my server has crashed running centos4, i can > not > > ping or access the console but the hardware is > still > > running. it does not leave
2007 Mar 19
1
cs 1.6 instant lag problem NEEDED FIX!
ok i'm in a really tiresome and annoying pickle here. aurite, so, i installed steam on latest wine w/e and installed cs 1.6, i can join multiplayer servers but whenever i'm playing there's this instant lag like whenever i'm walking or something i just lag for some odd reason and it happens in an instant and it gets really annoying and i can't play cs cuz of this. me need help
2007 Jan 25
2
acpi=no command?
Hi I am trying to install CentOS 4.4 on an hp pavilion PC. It wont install just boots in a circle, so I think I have to pass acpi=no at boot stage. Can anyone give me a detailed explanation how do this? Thanks, -- Filianx -------------- next part -------------- An HTML attachment was scrubbed... URL:
2006 Nov 15
3
qemu/rtl8139: Max transmit frame size
Hi: I noticed a bug in the realloc error checking code in the QEMU backend for RealTek8139. However, what''s worse is that there is no cap on the total size of the transmit buffer at all. So a guest can keep extending it until memory runs out. CP_TX_BUFFER_SIZE is already 64K. So it seems to me that we don''t need the while loop to extend the buffer at all since no transmitted
2004 Oct 28
4
HTB is losing packets ?
Hello all, I have using htb for last 10-12 months to manage the bandwidth share. Until last month everything was ok, but now after a kernel upgrade (from 2.4.20 to 2.4.26 because a kernel bug that generate a oops) the Linux router is droping packets. It is weird because the "tc -s class ls dev eth1" (in the class I monitor) reports no packet drop, the "tc -s qdisc ls dev
2013 Feb 16
2
Boot problem with Debian Squeeza and Xen
Hi all, I just upgraded my Debian/Etch with Xen3.3 machine to Debian/Squeeze Xen4.0 and now have problems with starting the Dom0 kernel. I always get the error message: Kernel panic not syncing: the kernel parameter noapic is incompatible with xen. My grub.cfg is: menuentry ''Debian GNU/Linux, with Linux 2.6.32-5-xen-686 and XEN 4.0-i386'' --cl$ insmod part_msdos
2006 Apr 12
13
rhtml produces so many white places?????
Hi, I have a rhtml file that uses some ruby code inside, there are not too ruby codes, but it repeats itself thousands of time. I find out each time when the ruby code execute, it will produce the html code correctly. But the produced html will conseved the "format" of the rhtml, and it adds a lot no used white space!!!! example : toto.rhtml <body> <table> <% data.each{