similar to: Sending and receiving

hi, (assume HTB) I was thinking will it be possible to do some sort of UNFAIR-SHARING :"), what I have in mind : Say I have a internet link with 100kbits bandwith, then I want to share it between many clients (which will increase over time). Let''s i start with 5 clients with rate = 30kbits... See the total bandwith of users is 120kbits but I have only 100kbits.... So where is the

If I create a cbq qdisc as a leaf of a cbq class, the bandwith rate is the same of the root cbq qdisc or the rate of the cbq class? Does exist the parameter rate on the "tc qdisc add" for cbq command? tc qdisc add dev eth0 root handle 1:0 cbq bandwidth 10mbit avpkt 1000 cell 8 tc class add dev eth0 parent 1:0 classid 1:3 cbq bandwidth 10mbit rate 50kbit allot 1514 cell 8

tc qdisc add dev eth0 root sfq perturb 10 I want to set perturb to 8 then i used this tc qdisc add dev eth0 root sfq perturb 8 system give me the following message RTNETLINK file exists I delete the rule by this :"tc qdisc del dev eth0 root sfq perturb 10" please tell me how can i delete the rule by another way and where is "RTNETLINK file"

hi,Stef: I read your burst test,I have some questions remain. A and B have immovability bandwith: If I bound bandwith to machine A and B,in order to it have 4Mbps,the other machine B have 6Mbps,(I have 10Mbps total). between them no permit bend from each other. whether burst cburst tokens ctokens value is zero. it''s right? --------------------------------- Do You Yahoo!?

How to do ensure a class not lended and not borrowed each other. I do cburst burst 0b ,but ctokens tokens go to negative! --------------------------------- Do You Yahoo!? "更多惊喜，同样精彩，NetVista A30 热卖" --0-611462377-1048485942=:33792 Content-Type: text/html; charset=gb2312 Content-Transfer-Encoding: 8bit <P>How to do ensure a class not lended and not borrowed each

dear All, I'm a new student and my job is too shapping bandwith for our campus faculty network. I want to implement htb with Redhat-9.0 distro. does this distro kernel support htb and tc good ? or i should apply some patch or upgrade kernel ? regards reza

Hi, If I have a DSL router with 300kpbs upload bandwith: Linux(eth0) ---(100Mbps)---> DSL ---(300kbps)---> INTERNET Which is the recomended value I must set in my QoS setup for the maximum outbound bandwith of my ethernet interface ? The max of 300kbps or something less like 290kbps ? Especify less than the maximum available bandwith is advisable to ensure that the QoS algoritms goes

Hello, I am running linux red hat 7.2 and still somewhat unfamiliar to its commands. I am administrator to an ISP with about 80 clients and would like to regulate the speed of uploads and downloads. I understand that I need to place everybody in different class''. Could I get help how to use tc/QBC to limit bandwith and impliment a u32 (or fwmark) filter that names mac

Hi, I''m fighting seriously with a most simple HTB setup. I''d like to share the incoming 64kbps into 5 and 59 for two different machines under NAT. HTB seems to hold the required limits when ceil is not set (no borrowing), but when borrowing enabled it seems to share equally rather then keeping the specified ratio. My setup is below. A typical output of "tc -s -d qdisc

Hi, I live in a rural community where adsl and cable is not widely available. I correctly have an option of using adsl or cable at my location. Ten miles away my friends apartment building has no option of cable or adsl. I set-up a wireless link between my friends apartment building and my house. It works great for him and me and the adsl company doesn''t care because they

how can I configure for shaping bandwith using cbq/htb without delay or latency?

Hi! I answer to two messages from this thread (I use digest). lartc-request@mailman.ds9a.nl wrote: > > Message: 3 > Date: Fri, 16 Jul 2004 10:51:37 -0700 (PDT) > From: ibro tj <ibb_linux@yahoo.com> > Subject: Re: [LARTC] QoS for Voip. > To: lartc@mailman.ds9a.nl, alessandro.ren@opservices.com.br > > Hi, > > the hint from Martin A Brown which I am

Hi, Does anyone know where can I find a Web Interface, or Webmin Module for configuring Shaping Rules, Qos and VPNs Bandwith Management in general....etc?? Would apreciate any help. Thanks Osgaldo. _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

Hi,All I am using iproute2 to manage bandwith for ADSL router.High,medium,low priority are needed for different protocol port on the ADSL's upstream side,as following: LAN --- |ADSL Router|------WAN When there aren't traffic on the specific priority, its bandwidth should be borrowed by other priorities.But it doesn't work.Here is my script: /usr/sbin/tc qdisc del dev nas0 root

I have an htb qdisc setup and it is shaping my traffic wonderfully but I''ve just recently started taking a look at the output from the command tc -s class ls dev eth? Looking at the "rate" line I thought to myself..."cool I can use this to graph throughput avg.es without having to worry about the "Sent bytes" rolling over or being lost when the htb qdisc is

Hi Stef and Alexey I have read some documents about CBQ algorithm from http://www.icir.org/floyd/cbq.html but still have some question about CBQ in Linux . 1. First estimator can estimate how much bandwidth already USED per class. one estimating algorithm is EWMA (exponential weighted moving average), how about Linux implemenatation about estimator? also do you have link for this algorithm? I

Hello ALL, is there a way to have a device independent qdisc, or a qdisc on some kind of virtuall interface? Background: I have a 5-Interface-Router with one Internet-Uplink. The Router should connect the clients on the other Interfaces to the Internet and to each other client. As i understood the hole TC stuff i can only get influence of outgoing traffic. In my case i can reduce the traffic of

Hi all, After a long reading of the LARTC, I were able to set up a working HTB config on my firewall. But my question is : Can I use a "ip less" box to do QoS ? With bridging software (or even without?) or thing like this and use an u32 filter to direct the traffic to the right class ? In other words, I can''t modify the existing network config or inster into (netmask is

Hi group, first of all: I am new to this group and hope to bring in some value later. At the moment I am such a beginner that I will probably of no use to anyone and only be asking stupid questions... I am running a little private linux server with kernel 2.4.21. It serves as a gameserver, webserver and mailserver, mainly. It also does the pppoe connect via a DSL modem to my provider and the NAT