similar to: cbq + gred doesn''t drop packets

Hi, I am trying to get assured forwarding/expedited forwarding with gred and htb working. Below is the script I am using. The following steps are what I thing is how the script works. My problem is that if I remove the HTB qdisc from the script and have the GREDS parent as the dsmark it works, but when I add the htb as a parent of GRED and DSmark the parent of htb it does not work? Any

All: I am tasked with creating an environment in which DiffServ and IP precedence is handled as close to RFC specification as possible. I have a few problems with implementing this based on current queueing structure. Here are a few of my questions. 1.) Is there any way to get DiffServ AF drop levels without using DSMARK and GRED? Ex. AF11 Gred DP 1 AF12 Gred DP 2 AF13 Gred DP 3 2.)

Hi, I am tring to setup AF on my router using GRED/HTB. I plan to mark and set the DSCP with iptables and the ingress qdisc to set the tc_index for the proper GRED vq(1-12). My question is: Is there a way to allow for priority between the af classes and within the af classes? also would it be possible to to the following: HTB(6Mb) | GRED(1)grio HTB1 (af1) (1MB) GRED(1-3)grio |

Hello all, Please could someone help me with this, I have been trying for days to get this to work. I would like to have BE, AF & EF classes with HTB qdisc. I can''t find any scripts online where this has been done. If I enable this filter: #tc filter add dev eth0 parent 2:0 protocol ip prio 1 \ #tcindex mask 0xf0 shift 4 pass_on then BE & AF classification seems to be fine but

I ''ve been trynig for a long time now to make HTB and GRED to work togethen. The problem beeing that GRED doesn''t use handles (instead it uses DP:1 DP:2 etc) i can not preperly filter traffic to them. Tomas Graf suggested to use the tc_index index of u32 classifier so dear Sant .. i am currently with the following scripts that works! But when i try to add an HTB before the

ALL: <<diffserv-gred_10-06>> I have attached the current script that I am using. $TC qdisc add dev $EDEV parent 2:20 gred setup DPs 3 default 2 grio $TC qdisc change dev $EDEV parent 2:20 gred DP 1 limit $lim min $minTh max $maxTh avpkt $avgPL burst $bursty bandwidth $netBand probability 0.02 prio 2 $TC qdisc change dev $EDEV parent 2:20 gred DP 2 limit $lim min $minTh max

Hi, I am trying to implement a simple scaled-down version of the AF traffic class type. As such I basically want to remark non-conforming AF11 packets to AF13. Here is m script that I have been using on the ingress router of my network: ---------------------------------------- Link=''dev eth1'' Rate1=''rate 800Kbit'' Rate2=''rate 2500Kbit''

Hi, just wondering if this type of configuration would be possible for using AF and EF classes. HTB (6.0M) --GRED 5 (AF1) --HTB(1M) [is it possible to have this with a 1M rate and a 6M ceiling?] --GRED [3 greds using grio] VQ1 -3 --GRED 4 (AF2) --HTB(1M) --GRED VQ1 -3 --GRED 3 (AF3) --HTB(1M)

I''m successfully using HTB + GRED to shape traffic based on the DSCP field. I would like to strip the DSCP and possibly replace it with normal ToS bits on egress traffic leaving my network. Leaving DSCP set is pointless, and could potentially cause problems with some ISPs that use DSCP internally I suppose. Setting ToS bits would seem ideal as most networks still honor it to varying

Hello, We know, VQs are used in Gred to offer different schedulers, in order to make clear what the VQs are, I have read the sch_gred.c in net/sched/. In the function gred_enqueue(), at first it will find the VQ(q) according to the lower four bits of the skb->tc_index, then some parameters of the q is modified, such as q->packetsin and q->bytesin. At last the packet was put into the

I want to set the DSCP field of the incoming packets. And then put them in the correct queues. I can mark the packets: iptables -A OUTPUT -t mangle -d 10.10.10.12 -j MARK --set-mark 1 tc qdisc add dev eth0 handle 1:0 dsmark indices 64 set_tc_index tc class change dev eth0 classid 1:1 dsmark mask 0x3 value 0xb8 tc filter add dev eth0 parent 1:1 protocol ip prio 1 handle 1 fw

Hi: Execuse me if this has been mentioned before, I''ve looked around the archive but did not find anything about the problem I met. I''m trying to use tcindex to classify the the packet outgoing to one interface. I do as the following : tc q a dev eth0 root handle 10:0 cbq bandwidth 10Mbit avpkt 1500 tc c a dev eth0 parent 10:0 classid 10:1 cbq bandwidth 10Mbit rate

hi, Is there a way to calculate Gred parameters, given a desired delay (e.g 100ms)? Thanx Ntanzi ____________________________________________________________________________________ Do you Yahoo!? Everyone is raving about the all-new Yahoo! Mail beta. http://new.mail.yahoo.com

Hi, In the GRED queueing discipline of linux traffic control, we can define around 16 Virtual Queues with different RED parameters for each one of these. As far as I think, while applying RED on each of the virtual queues, with the grio option set, quave(the average queue length) of a virtual queue with priority= n is given by the sum of the virtual queues with priority greater than n ... I have

Has anyone ever managed to use GRED and HTB ? Been googling all over the net for hours and did not manage to find any proper implementation. In my case all AF traffic goes into VQ 3 In opalsoft afhtb example traffic goes into VQ 1 & 2 any script will do just fine for me Thanks in advance , Antonio _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl

Sorry all, this is the missing email that I referred to previously. I inadvertently sent it only to the original poster rather than the list. Sorry for the wasted b/w for those who don''t care... Ed W -------- Original Message -------- Subject: Re: [LARTC] RED/GRED implementation for InBound Traffic Control (from ISP) Date: Fri, 09 Jul 2004 22:04:30 +0100 From: Ed Wildgoose

Im experimenting with using a Linux machine with 3 interfaces to operate as a core router. All links and network interfaces are 100mbit. Below is a ascii diagram of the network. (network A) edge router ------>core router---->edge router (network C) ^ | | edge router (network B) I have tried two

Hello, I have the following proplem. My DiffServ configuration is working fine when I do ping, but when I use mgen the packets are not detected at the core router. Here is my core router configuration: #!/bin/bash tc qdisc add dev eth1 handle 1:0 root dsmark indices 64 set_tc_index tc filter add dev eth1 parent 1:0 protocol ip prio 1 tcindex mask 0xfc shift 2 tc qdisc add dev eth1 parent

Fixes issue #95 on GitHub. --- src/opus_multistream_encoder.c | 57 ++++------------------------------ 1 file changed, 6 insertions(+), 51 deletions(-) diff --git a/src/opus_multistream_encoder.c b/src/opus_multistream_encoder.c index 6cc1f432..9cb9bf34 100644 --- a/src/opus_multistream_encoder.c +++ b/src/opus_multistream_encoder.c @@ -742,20 +742,9 @@ static void ambisonics_rate_allocation( {

Change-Id: I16bd4cd990d8ad5888c9e30016218ac25242ecb5 --- src/opus_multistream_encoder.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/src/opus_multistream_encoder.c b/src/opus_multistream_encoder.c index 30cafe1..c07132f 100644 --- a/src/opus_multistream_encoder.c +++ b/src/opus_multistream_encoder.c @@ -747,7 +747,8 @@ static void ambisonics_rate_allocation( if