Displaying 20 results from an estimated 30000 matches similar to: "dynamic load balancing"
2005 Nov 16
0
load balancing
Hi, I have 2 routers that are connected using 2 gre tunnels over ipsec, and ospf. Ospf sets up the equal cost
route, but uses the ''equalize'' in the route. Is there a way to remove/disable packet based load balancing? I would
just like to do a flow based load balance?
thx jason
_______________________________________________
LARTC mailing list
LARTC@mailman.ds9a.nl
2005 Jan 21
0
equal cost multipath routing and incoming services...
We''re trying to figure out how to have equal cost multipath routing using OSPF (quagga) and have come up with the following...
Has anyone done something similar? -- How do you deal with incoming services (mail/web/etc) in such a scenario as below - And does anyone have any suggestions?
There''s more detail below....
Diagram and overview:
Network A connects to Core1 and Core2
2003 Mar 27
1
OSPF problems
I have a fairly simply laid out network that could easily use static routing. However, I
plan to expand quickly and don''t wish to spend the better part of my life maintaining
static routes.
INTERNET
|
---------
Gateway | - LAN 172.16.1.x
| - LINK 192.168.1.1
---------
|<----wifi
---------
router 2 | -LAN 172.16.2.x
| -Link 192.168.1.2
---------
2002 Nov 21
22
many ways to do load balancing (or not?)
I''m a little confused about the many ways I''ve read that can be used
for traffic load balancing, that is, two or more interfaces to the
outside world being used transparently and efficiently by the internal
machines.
I heard about:
a) netfilter SNAT to more than one IP. If I''m correct, this is only
a round robin, that is, one connection goes here, the other goes there,
2003 Jun 20
1
doubt about Load Balancing
Hello
In the LARCT how-to subitem: 4.2.2. Load balancing the following phrase
says:
"" Instead of choosing one of the two providers as your default route, you
now set up the default route to be a multipath route. In the default kernel
this will balance routes over the two providers. It is done as follows (once
more building on the example in the section on split-access):
ip
2007 Apr 24
0
OSPF with Netem
Hi all,
I am currently trying to emulate a satellite link, via Netem, on a testbed which is OSPF-enabled.
I''d like to set up a Netem box between two routers.
Since all routing between routers is dynamic, I''m wondering how to set up OSPF on my Netem box?
Could someone indicate me if it is feasible and give me some guidelines to possibly do so?
Thanks in advance,
Vincent.
2004 Apr 30
0
Load-balancing with multipath routes (1 NIC + 2 GWs)
Greetings,
I''m trying to set up some sort of load-balancing on a Linux (Trustix)
gateway by using multipath routes, however I''m stuck with some problems.
The idea is that this gateway (odd as it may seem) only has one external
interface, which should route packets to two different gateways (Ciscos).
The gateway''s external interface and the routers are all on the same
2005 Jul 18
0
Load balancing (LARTC 4.2) over 2 connections on 2 routers.
Hi,
I''m building a network similar to that seen in 4.2 of the LARTC Howto.
There is a diagram of this attached to this mail.
Addendum to diagram:
AlexRouter br0 = 192.168.58.1
eth0 = dhcpcd
DaveRouter br0 = 192.168.58.2
eth0 = dhcpcd
But we''ve run into some problems when actually implementing the routing
for multiple uplinks.
The difference between my
2007 May 10
0
FW: Load balancing using connmark
-----Original Message-----
From: Salim S I [mailto:salim.si@cipherium.com.tw]
Sent: Thursday, May 10, 2007 5:22 PM
To: ''Francis Brosnan Blazquez''
Subject: RE: [LARTC] Load balancing using connmark
"I think the main advantage of shorewall solution is that it applies
connmark to incoming packets from the wan as you point, leaving load
balancing to outgoing connections to the
2004 May 27
0
Auto Load Balancing in Linux sever
Hello,
Im having an intranet of 100 linux machines sharing the internet and
have two lease line internet connections Does anyone know how to auto load
balance in the intranet server considering the current traffic, bandwidth
etc, instead of using static routes with iproute2.
Thanks in advance
Jayesh
_______________________________________________
LARTC mailing list /
2005 Nov 13
0
Again: Re: MSN keeps disconnecting with load balancing (fwd)
This ''MSN'' is a web site? Im guessing it ''refresh''es every 5 minutes or
so.
They are proably testing cookies against the ip address they appear to be
comming from. This is horribly wreckless of them if they arnt offering
IPv6. Are they? They only way i have to remedy this problem is to get
their IP range and bind it to the most stable connexion you have,
2004 Feb 19
1
Load Balancing with compile redhat 8 vs Kudzu
Hello
I got a nice problem, i don''t know if the i''m put my question a the right
place, but anyway....
I have 3 server LINUX with LVS (linux virtual server) I had to recompile my
kernel cuz it was not supporting LVS. Since there, everything was going
right. Then I''ve change the hard drive of the primairy LVS to an other
computer, now i want KUDZU to detect my harware,
2005 Feb 09
0
A newbie question
This issue may sounds trivial
I need to build a Router for send Internet + VoIP traffic.
The computers are in a different network that the Phone Gateway.
The Computers are going to be send to a 3 Mbps connection using OSPF, in the
meantime the phones are going to be send to a T1 using OSPF too.
The routing software is going to be Zebra.
I need to switch the outgoing in case that the T1 or
2005 Jan 31
3
load balancing between two default gateways
Hi list gurus,
long story short we have firewall machine which is the default gateway
for our clients and firewall send traffic out to Internet via cisco router.
On cisco we have two serial interfaces 1Mb and 2Mb.
On firewall
#route add default gw xxx.xxx.xx.xxx (for 2mb)
#route add default gw xxx.xxx.xx.xxx (for 1mb)
and the same rule for Imb link route packets via these two links.
However I
2004 Apr 18
1
Load balancing over 4 interfaces
Hello lartc!
I have strange problem setting load balancing over 4 interfaces.
Something won''t accept more than 3 interfaces,
While setting:
ip route add default scope global \
nexthop via 0.0.0.0 dev pvc0 weight 1 \
nexthop via 0.0.0.0 dev pvc1 weight 1 \
nexthop via 0.0.0.0 dev pvc2 weight 1
It''s ok:
ip r l
default
nexthop dev pvc0
2004 Dec 26
1
load balancing over multiple ISP links
Hi,
Can someone explain in technicality on how the load balancing over
multiple ISP links?
Regards,
ro0ot
_______________________________________________
LARTC mailing list / LARTC@mailman.ds9a.nl
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
2004 Sep 15
1
load balancing
hi, question.
i was reading the howto, and the part about load balancing talk about to
providers, well i have one provider and make to dial-modem conection, so i
have the same gateway in both (ppp0 and ppp1) but to diferent IP.
what do i have to do?
just set up the default route to be a multipath route?
or do i need to split the access?
_______________________________________________
LARTC
2004 Nov 18
1
same gw / load balancing
Hi
I want to use two dsl (or more) lines to increase my internet bandwidth.
Our dsl lines are dhcp serviced, so when we pull together two dsl
modems, both of them provide the same def gw and different ip in the
same subnet (i also assume that arping gives the same MAC for the def gw
since it''s a bridged network).
¿Is it possible to balance outgoing traffic "using" the
2004 Nov 20
2
Same GW for load balancing
Hi
I want to use two dsl (or more) lines to increase my internet bandwidth.
Our dsl lines are dhcp serviced. Both of them provide the same Def GW and different IPs for each ethernet interface (same subnet).
¿Is it possible to balance outgoing traffic "using" the interface as a
criteria? No point on choosing gateway by IP.
¿Could someone give me a clue on how to deal with this?
(first
2004 May 17
1
Re: Load Balancing 4 cable modems, followed nano.txt
Hello,
On Mon, 17 May 2004, Charles-Etienne.Dube wrote:
> I did some tests with 2 cable modems, but now it is installed in a production
> environment with 4 cable modems. At first, everything seemed to work fine..
> But now I had a couple of users tell me that some web pages were
> not available while others were, and it semms to be a masquerading problem
> since when I