similar to: Where to assign weights to different flows?

I try to shape traffic using HTB and mark packets within iptables using PREROUTING. But the filterrules seems to ignore the marks set with PREROUTING Only POSTROUTING marks are accepted. First my configuration I have a router connected to the internet via ADSL over interface ppp0. eth0 is a tunnel to ppp0 and eth1 serves the LAN. LAN is 192.168.57.0/24 on 10Mbit ppp0 is 80.126.16.44 on

I thought I had this all worked out, but it seems not. The following tc configuration: tc qdisc del dev ppp0 root 2> /dev/null > /dev/null tc qdisc add dev ppp0 root handle 1: tbf rate 120kbit burst 1200 limit 1 tc qdisc add dev ppp0 parent 1:1 handle 2: prio bands 3 tc qdisc add dev ppp0 parent 2:1 handle 10: sfq perturb 20 tc qdisc add dev ppp0 parent 2:2 handle 20: sfq perturb 20 tc

Hi all, Im new to all this, and am still trying to get my head qround some of the concepts of how this all works. Ive read the howto''s, man pages etc. Ive setup packet shaping on my router/server box using HTB and SFQ, but its not working the way i would like. Im after shaping that has "weights" for classes so that a lower priority class will slow down when a higher class

Hi Is there a way of marking packets by mac address instead of ip or ports using a "tc filter u32 match"? I read somewhere that I could use the offset -8 and -14 to grab the mac addresses but if I use anything lower than -8, for example -9, I get an error. I''m modifying the wondershaper script to cap the download speed by mac address. Any sugestions?

Hello everybody, sorry for bothering you, but after some hours, I''m stuck. I''m living in a student''s foundation where I want to connect lots of people to a tiny DSL link. We have exactly four types of traffic. We want a really hard PRIO solution (as I promised to someone that group X will only use the link capacity which isn''t used by group Y). I could make a

Hi All, I''ve been playing with QOS for a short while now and have worked out how to do what I want using HTB. Great queuing discipline btw. My problem is the tc filters I want to setup aren''t working because iptables is getting to the packets first and mangling the src address. The iptables script I am using is MonMotha''s Firewall 2.3.8 and it includes lots of nice

Hello! My system is: Internet ADSL(PPPoE) ---> ppp0 [LINUX server(router)] eth0 ---> LAN Server(router) is running on LINUX Slackware 8.1. I have recompiled a 2.4.22 kernel, enabled all QoS support in the kernel config, including HTB. My ADSL bandwidth is 256Kbit/s for download and 64Kbit/s for upload. I use the following HTB+IPTABLES configuration, because I want to reduce bandwith for

> From: "CIT/Paul" <xerox@foonet.net> > Any help would be greatly appreciated :) This is much better than SFQ :> Sounds like SFQ to me. Can you tell us what the differences are?

Hi all. I''m going on my 3rd week trying to get a simple traffic shapping to work the right way :( !! My goal it to shape the traffic coming from one machine (pc1) to another machine (pc2) throught the "eth0" interface. My test configuration is as follows: PC1   IP: 192.168.105.237   Mask: 255.255.255.0   OS: Red Hat Linux Kernel 2.4.20-8   Rules:

I run a small Linux webserver and NAT router from my cable modem at home. Whenever someone starts an http download, all other traffic from my LAN is starved. Bandwidth is not really an issue, but latency is particularly horrible -- pings that usually come back in 20ms can take up to 600ms while the web server is active! I set up QoS (netfilter+iproute2) on the NAT machine in an attempt to give

I am looking for a good htb traffic shaping script to prioritize incoming traffic over outgoing traffic for my machine. I have a 100mbit line, ftp up, backup data comming in, but whenever mirrors starts grabbing it they use all the traffic and the backup data comming in (the important data) drops to like 300kb/sec. I was thinking some script doing sleep 60 [if downstream > 1mb/sec, limit

I shape my upstream cable link with HTB from a script. My voip traffic (from the 192.168.0.14 host) gets priority over everything else to the near-starvation of other classes; the rest of the traffic is split up based on some priority rules (qos, empty ack packets, etc). eth1 is the uplink I''ve been using HTB and fw marking for the job until recently, when I changed the queue structure

Hello At first I must tell you that I´m a real newbie with Linux (and english as well...) I´m using 2 vlans and shaping works quite well without vlan Now I want to do load balancing at these vlans. Any vlan should get the same minimum/maximum bandwidth of download and use the bandwidth that isn´t used by the other one at the moment. But with vlan the shaping doesn´t work. Can you please tell me

hello to all i''m trying to set a filter but doesn''t want to work. i''ve set ut the qdiscs and the classes like this : tc qdisc add dev ppp0 root handle 1: htb default 20 tc class add dev ppp0 parent 1: classid 1:1 htb rate 120kbit tc class add dev ppp0 parent 1:1 classid 1:20 htb rate 30kbit ceil 120kbit tc class add dev ppp0 parent 1:1 classid 1:21 htb rate 30kbit ceil

Hello, I have a serious problem with HTB which I wasn''t able to solve myself. I run a masquerading router with ppp0 as interface to the Internet. Three clients need to share a downstream of 1 MBit, which I want to divide with tc. When I see a packet being forwarded to one of these clients, I give it the appropriate unique mark: iptables -t mangle -A FORWARD -d 192.168.34.141 -j MARK

Hi All, I''m using iptables-1.2.7a on RedHat8 kernel 2.4.20. I wanted to limit the file-sharing traffic to the internet. I marked the packets with iptables: iptables -A FORWARD -t mangle -p tcp -s 192.168.1.1/24 -d ! 192.168.1.1/24 --dport 1024:1862 -j MARK --set-mark 1 iptables -A FORWARD -t mangle -p tcp -s 192.168.1.1/24 -d ! 192.168.1.1/24 --dport 1864:65535 -j MARK --set-mark 1

Hi folks, I read the fantastic LARTC How-to and after that i tried to limit one host in my LAN for both down-and upload bandwidth usage. I took section 15.9. and added uplink-limiting as I understood it from the previous chapters. Unfortunately it doesn''t work. I ran the script and went to the specified PC, started a download, and watched the rate. The rate was always about 2000 kbit/s,

I have: tc qdisc add dev imq0 root handle 1: htb default 30 tc class add dev imq0 parent 1: classid 1:1 htb rate 512kbit ceil 512kbit tc class add dev imq0 parent 1:1 classid 1:30 htb rate 64kbit ceil 512kbit then: iptables -t mangle -A PREROUTING -i ppp0 -s 192.168.2.2 -j IMQ --todev 0 tc class add dev imq0 parent 1:1 classid 1:22 htb rate 64kbit ceil 128kbit tc filter add dev imq0 protocol

root@Delta:~# tc filter add dev ppp0 parent 1:1 flowid 1:5 protocol ip Unknown filter "flowid", hence option "1:5" is unparsable root@Delta:~# tc filter add dev ppp0 parent 1:1 classid 1:5 protocol ip Unknown filter "classid", hence option "1:5" is unparsable I don''t understand why it does not work. Can anybody explain me this problem? --

Dear list: I have a problem I cannot handle yet, and need to solve it as soon as possible. Would be very greatful with anybody who can help me. I have a 512/512 link to internet, that I want to share between several computers. I have eth0, with a public IP address, conected to Internet, and also, eth1, with a private IP address, for network with the surfing computers. I have a main class with