similar to: why there is any traffic in default class?

how to see which packets is going in to default class? -- Denis Kot denis?jabber.org.by ICQ: 13680126 Mobil: +375 29 6-1234-78 _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

Hi ! I have a single host which is connected via an 512kbit ADSL link to the n= et. I quite often use some realaudio application that uses some bandwidth = and I want to avoid other traffic to scale that bandwidth down. So I used = some classes (with htb) on imq0 device and applied some filters and it see= ms to work in most cases. However, there are some sites with which downloa= d is

I have this: class htb 1:29 parent 1:1 prio 0 rate 3000bit ceil 100000bit burst 1599b cburst 1611b Sent 33233 bytes 772 pkts (dropped 0, overlimits 0) lended: 415 borrowed: 357 giants: 0 tokens: -3756376 ctokens: 128779 or this: class htb 1:21 parent 1:1 prio 0 rate 3000bit ceil 100000bit burst 1599b cburst 1611b Sent 57554 bytes 618 pkts (dropped 0, overlimits 0) lended: 193 borrowed: 425

Hi! I have read all informations i could find, but some things are still not clear. My setup is: ---INTERNET1(eth0)-\ /- Local net1 (eth2) GW ---INTERNET2(eth1)-/ \- Local net2 (eth3) I have NAT and a working setup using HTB,SFQ, classifying with the iptables -j CLASSIFY way. I shape only the traffic coming from the internet heading to the intranet. I would like

Hello, I wrote a simple traffic shaping script (below) that should have allowed me to shape my internet traffic a bit (ppp0 - adsl 128kbit/64kbit; local interface eth0). The script works only partially - the speed is being limited but too much. Without running this script my download rate is about 10kBytes (with second computer also downloading at about 6kBytes). After running it my download speed

On my debian woody (kernel 2.4.31) the tcpdump doesn''t work with imq0 devices. If I try to tcpdump imq devices there is no packet seen: [...] rt1:~# tcpdump -n -i imq0 Warning: arptype 65535 not supported by libpcap - falling back to cooked socket tcpdump: WARNING: imq0: no IPv4 address assigned tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on

i''m trying to limit upload and download but something is wrong(it is about NAT) i will post here my "script" maybe someone could tell me what is wrong my kernel(2.6.9) is patch with imq(linuximq.net) and my iptables(1.2.11) also #flush tc qdisc del dev eth0 root tc qdisc del dev eth1 root tc qdisc del dev imq0 root tc qdisc del dev imq1 root ifconfig imq0 down

Hello, I have a serious problem with HTB which I wasn''t able to solve myself. I run a masquerading router with ppp0 as interface to the Internet. Three clients need to share a downstream of 1 MBit, which I want to divide with tc. When I see a packet being forwarded to one of these clients, I give it the appropriate unique mark: iptables -t mangle -A FORWARD -d 192.168.34.141 -j MARK

Hello I have a server with a dsl connection on eth1 and local interface eth0. Because of the NAT i cannot direct traffic to IMQ device in PREROUTING chain but have to use INPUT and FORWARD. So i use rules. iptables -t mangle -A INPUT -i eth1 -j IMQ --todev 0 iptables -t mangle -A FORWARD -i eth1 -j IMQ --todev 0 And now the strange thing: FORWARD traffic gets directed nicely to the IMQ, but

Hi all, my IMQ device works OK (thanks to Andy Furniss), but now I''ve problems to attach the traffic in the qdisc''s. This is my conf: ----------------------------------------------------------------------- INET | |eth0 300Kbps ROUTER (NAT) |eth1 | LAN ----------------------------------------------------------------------- MAX=300 tc qdisc add dev imq0 root handle 1: htb

Alejandro, So, i did try the script that you give to me, and the problems its continues.- Maybe the problem was in the IPTABLES rules, i attach the complete script below: ##################### ifconfig imq0 up tc qdisc add dev imq0 handle 1: root htb default 30 tc class add dev imq0 parent 1: classid 1:1 htb rate 500kbit ceil 2000kbit tc class add dev imq0 parent 1:1 classid 1:10 htb rate

Hi folks, I`ve a problem to use HTB and SFQ. The first script, below, to show a simple configuration, does work fine...!!! But, in the second example, does not work, becouse i put more code to clasify the traffic by protocol, http and ftp in this case. Somebody can tell me the errors? Thx, in advance.- NOTICE: IMQ device is to asociate with ETH1 my external iface. SCRIPT que funciona:

Hi! By iptables I set marking (-j MARK) just before -j IMQ. There are only three marks. Exectly all of them are ditected to 1:20 Why I see 3 pkts in default 1:30? How explain it? ### imq0: queueing disciplines qdisc htb 1: r2q 10 default 30 direct_packets_stat 0 Sent 631429 bytes 1812 pkts (dropped 0, overlimits 20) ### imq0: traffic classes class htb 1:20 root prio 0 rate 100Kbit ceil

Hey Andreas, how i catch this traffic using L7 filter?, i´ve installed l7 filter now, but i don´t kwnow to use the kind of filter...!!! Can you help me? Thx.- Terraja-based 2007/4/29, lartc-request@mailman.ds9a.nl <lartc-request@mailman.ds9a.nl>: > > Send LARTC mailing list submissions to > lartc@mailman.ds9a.nl > > To subscribe or unsubscribe via the World

Hello, does anyone have a working solution for the shaping both incoming and outgoing traffic in such way, that for a given client the *sum* of incoming and outgoing traffic is somehow defined? My ISP does the same thing, it gives me just a line of a defined rate, no matter the traffic direction (i.e. here is your line, the clock speed is 1024kbps, do what you want). I''m a litte bit

hi stef oone more pb while shaping incoming traffic with imq .this one tc qdisc add dev imq0 root handle 1: htb default 20 tc class add dev imq0 parent 1: classid 1:1 htb rate 2mbit burst 15k tc class add dev imq0 parent 1:1 classid 1:10 htb rate 1mbit tc class add dev imq0 parent 1:1 classid 1:20 htb rate 1mbit tc qdisc add dev imq0 parent 1:10 handle 10: pfifo tc qdisc add dev imq0 parent

ive got such network: |--------| |-------------| | WORLD |---|ROUTER/server| ------ NATED LAN |--------| |-------------| I want to use imq on ROUTER, what behaviour to choose ? AA, BA, AB, BB ?? --

Hello I have 2 class-B networks (172.22.0.0/16 and 172.23.0.0/16, over 130k of ip''s) and need to setup traffic tbf shapers with 64kb/s for each ip from 172.22.0.0/16 and 128kb/s for each ip from 172.23.0.0/16 just read lartc and don''t understand how to use u32 for decreasing number of rules and hashing

Hello, I have HTB on IMQ device. My rate does not work as I configured. I configured 1920kbit/s and I can download only about 290kbit/s (while it should be the whole bandwidth). My script: /sbin/modprobe imq numdevs=1 /usr/local/sbin/tc qdisc del dev imq0 root 2> /dev/null > /dev/null /usr/local/sbin/tc qdisc del dev imq0 ingress 2> /dev/null > /dev/null /sbin/ifconfig imq0 down