similar to: Change HTB "final qdisc" of the default walk-throught class

I''m trying to implement something similar the the diagram in section 9.5.2.1 in the LARTC HOWTO, but must have missed something somewhere :( I''m trying to hack up wondershaper, as it looked like a good place to start.. Here''s where I currently at, but I''ve tried alot of different things, all failing, some worse than others. The end result is to throttle back 126

Hello I am using htb (krenel 2.6.14.3 + esfq patch from fatooh.org) to limit the bandwidth. But I want the absolute maximum rate to be for example 5Mbit and not to exceed it. here is the script: $tc qdisc add dev ${NETIF} root handle 1 htb r2q 4 $tc class add dev ${NETIF} parent 1: classid 1:21 htb rate 5Mbit ceil 5Mbit $tc class add dev ${NETIF} parent 1:21 classid 1:101 htb rate 2Mbit ceil

Hi! Is it HTB fully compatible with BOND interface? I have this setup (mode= fault tolerance) : BOND0 -> ETH0 + ETH1 BOND1 -> ETH2 + ETH3 ( http://www.kernel.org/pub/linux/kernel/people/marcelo/linux-2.4/Documentation/networking/bonding.txt ) HTB work very well with Class over BOND0. If I add Class for BOND1 it generate balance errors. Also with HTB.init

Dear list, I have the problem that child classes don''t seem to issue the parent class to borrow from their parent. This is a simplified version of my script: tc qdisc del dev $DEV root tc qdisc add dev $DEV root handle 1: htb default 10 tc class add dev $DEV parent 1: classid 1:1 htb rate 10mbit tc class add dev $DEV parent 1:1 classid 1:10 htb rate 1kbit ceil 512kbit #groups tc

Hi I tryed to use a htb qdisc/class on top of another htb qdisc/class as you can see bellow: #!/bin/bash tc="/sbin/tc" $tc qdisc del dev eth0 root $tc qdisc add dev eth0 root handle 1: htb default 40 $tc class add dev eth0 parent 1: classid 1:1 htb rate 100Mbit burst 15k $tc class add dev eth0 parent 1:1 classid 1:10 htb rate 50Mbit burst 15k $tc class add dev eth0 parent 1:1 classid

Hi to all I am studying HTB on LARTC how to. I realize a simple configuration on router: tc qdisc add dev eth0 root handle 1: htb default 30 tc class add dev eth0 parent 1: classid 1:1 htb rate 3mbit burst 15k tc class add dev eth0 parent 1:1 classid 1:10 htb rate 2mbit burst 15k tc class add dev eth0 parent 1:1 classid 1:20 htb rate 1mbit burst 15k tc qdisc add dev eth0 parent 1:10 handle 10: sfq

Hi! I have just started with traffic shaping, and after hours of reading websites, man pages asf. I am still stumped at one problem I have. The interface eth0 is attached to the outside world, and I have an openvpn tunnel to another part of the organization using eth0 and port 5001. The idea was that all traffic going through the tunnel would have top priority and the rest share

Hello, I''ve just compiled the kernel 2.6.17 and noticed an odd HTB behaviour. For instance: tc class add dev eth0 parent 1:1 classid 1:30 htb rate 1kbit ceil 750Kbit burst 15k tc filter add dev eth0 parent 1:0 protocol ip prio 15 u32 match ip dst 192.168.5.1 classid 1:30 The filter works ok and the traffic to 192.168.5.1 flows through the class 1:30, but the rate gets much higher than

hello. i have following setup: a machine (winChip 200mhz cpu, 32mb ram, linux 2.4.28) acting like a bridge with 2 interfaces (eth0 - to our ISP, eth1 - to our network) machine does not have any IP there is a 802.1q vlan eth0.2 eth0.2 and eth1 are bridged in br0 i have one 4mbit link which i share with my friend, i have 3mbit and he has 1mbit all our IP addresses are public and we have the

We have a Linux box that is acting as the gateway to the internet for about 400 people, typically there are not more then 50 of them using the internet at any given time. We would like to provide different levels of access to different users. For example 128kbps to some users and 256kbps to others. We have considered creating a class and qdisc for each user (using htb) however we don''t

I''m trying to build a QoS system that would divide the outgoing traffic into four categories, each one also subdivided into two more categories. For that I chose a htb root qdisc subdivided into four classes, each of these classes contains also a htb qdisc. Until these point everything goes well, but when I try to attach a new class to the leaf htb qdisc a problem with the sintaxis

Hi! I've noticed that an "rsync -avx . host:/test" tries to descend into a FUSE filesystem (on the origin/sending side). This is at least true when the FUSE is mounted by somebody else. I came accross this while my nightly backup choked on this with "Permission denied" at the mount point. FUSE is a mount subsystem in Linux that enables userspace filesystems. A FUSE

Thank you Andy! I did''t find why I could''t use the fw match in ingress. Now it works. Now I ran into another problem: When I try to add a pfifo_fast leaf qdisc dor htb classes it seg.-faults. Is pfifo_fast a special qdisc? I can succesfully add other type of qdiscs. I found that a similar problem was reported in february on a MIPS architecture. root@zefir:/usr/src# tc qdisc

Hi When I list all the qdisc with tc command it is not possible to see the parent of the qdisc. An example by the book. # tc qdisc add dev eth0 root handle 1: htb default 30 # tc class add dev eth0 parent 1: classid 1:1 htb rate 6mbit burst 15k # tc class add dev eth0 parent 1:1 classid 1:10 htb rate 5mbit burst 15k # tc class add dev eth0 parent 1:1 classid 1:20 htb rate 3mbit ceil 6mbit

Hello! I have an internet connection of 64kbps garanteed in a channel of 256kbps. On this connection the metropolitan speed is 10Mbps and in the provider''s network the speed is 100Mbps. I have a few clients behind my linux box and i want to set up some limitations because some of them are using it irrational. I am marking the packets with 0 for internet; 1 for metropolitan 2 for

Hi all ! I''m building a network appliance whose goals are to enhance Voip quality on 512/128k DSL links. But, i have a voice quality problem, and i think i''m doing something wrong, but i can''t find what. Please excuse my terrible english, i''m french. >From what i''ve read, tc is the tool i need. I read the documentations, readmes and lartc.org

Im using a Linux machine with standard pc hardware with 3 seperate PCI network interfaces to operate as a DiffServ core router using Linux traffic control. The machine is a P4 2.8ghz, 512mb RAM running fedora core 3 with the 2.6.12.3 kernel. All links and network interfaces are full duplex fast ethernet. IP forwarding is enabled in the kernel. All hosts on the network have their time sychronised

Hi, I''m trying to use prio qdisc with htb, however not the "usual" way (like for example FairNAT). Here is my idea: Root has HTB shaping traffic to link speed -> then goes PRIO queues -> each prio queue has HTB with sublasses for each user, should look like this: 1: htb qdisc | 1:1 htb class

please, help, i have build vpn server (suse 9 + poptop), i have managed to implement tc htb in ip-up script, but every client has own ppp interface (ppp0, ppp1, ppp2...), and my idea is to share available bandwidth, not to limit connection, how to build root tc rule, when I have more then one interface?... please any one width experiance regards _______________________________________________

Hello, I have problems with htb. The problem is that when I download any file via shaper with htb, the traffic is very dinamic, it jumps, for example: if i have set ceil = 128kbit the results that it jumps from 112kbps to 144kbps or smth like that maybe its not very bad, but when the traffic drops down to 40kbps or less and then after 1 or 2 seconds jumps to 144kbps, its bad :-( and it is often.