similar to: newbie downloading not working

Hi Guys After googling a little I couldn''t find the correct answer.. When I use : tc filter add dev eth0 parent 1:0 protocol ip prio 1 u32 match ip dst 192.168.0.11 flowid 1:30 , I can shape traffic to 1:30.( works like a charm) Now instead tc filter I would like to use CLASSIFY as below: iptables -t mangle -A POSTROUTING -o eth0 -d 192.168.0.5 -j CLASSIFY --set-class 1:30 but when I

Hi Guys After reading http://lartc.org/lartc.html#LARTC.QDISC http://www.docum.org/docum.org/ http://tldp.org/HOWTO/Traffic-Control-HOWTO/ http://www.opalsoft.net/qos/DS-21.htm and a wonderful figure from: http://www.opalsoft.net/qos/ds-lb-214.gif I have a newbie question. Suposse next figure: <--- up 128K internet ----- dsl ---------------------eth1 -Linux Qos- eth0 ------ LAN

----- Original Message ----- From: Michał Joachimiak To: lartc@mailman.ds9a.nl Sent: Tuesday, July 20, 2004 3:45 PM Subject: HTB - Really Big problem Hello everybody! Since week i dig lists and www and can''t find solution for my problem. I''m using HTB 3.13 kernel 2-4-25 smp iptables 1.2.9. I''ve got situation like this: LAN------Linux Box(routing only)------- Linux

Hi all, Long email but please be patient :) I am part of EHAS [1], a non profit organization which main goal is to improve the Healthcare assistance in isolated rural areas in developing countries. Recently we have developed a long distance Wi-Fi network in Cuzco (Peru). This network provides connectivity to 12 nodes (they are in fact Health Centers). As VoIP is a essential service in this

Hello i''m having some issues trying to match packets using iptables mark, iproute filter and tc filter.- i mean, when i do iptables -t mangle -A INPUT -p tcp --dport 80 -j MARK --set-mark 20 iptables -t mangle -A PREROUTING -p tcp --dport 25 -j MARK --set-mark 10 iptables -t mangle -A FORWARD -p tcp -i eth0 -o eth1 --dport 25 -j MARK --set-mark 10 $TC qdisc del dev $INET_IFACE root $TC

I have htb on 486 sx with 16mb ram. Slackware 9.1. Connection : dsl 1Mbit. 486 works as router and trafic shaper for network made of 12 pc''s. it does the job quite well, but when i play Counter-Strike or connect to my 486 via ssh (on lan), i get huge lag every 11-20 sec. when i connect to 486 via ssh and run iptraf program i see all the trafic, and after a while when lag comes the

Actually i gave up, i tried and tried and tried so many times, upgrading software falling back to an old version but it didn''t work, that''s it. i can''t do work together tc with iptables and iproute2 when i mark a packet with iptables tc doesn''t recognize them so it falls at the default leaf of the tc''s tree what i like is to mark packets depending on

Hi Stef, Sorry to write to you directly but my list membership is not working, I receive the archive but cant send to the list, cant delete myself because I don''t exist and can''t rejoin as they say I do exist, anyway hope you don''t mind Can you tell me what the difference between these two scripts is please. What I want to achieve is a high speed channel 1000kbit from

Hello! I''ve been trying to write a traffic shaper for a 128kbit line with this setup : 5 computers that get dedicated bandwidth and the rest go in a pool with bigger priorities. I made the attached script, but it seems it doesn''t work... It sends the traffic coming from the dedicated ips to the default class. Where is the error ? Will this setup work if the bandwidth is

Hello! I have a quite complicated setup. In my network on each interface there is bandwidth limitation for each user. Booth outgoing (on interface itself) and incoming (attached IMQ) traffic. There is main HTB class which limits bandwidth for whole interface and HTB subclasses for each user. Filtering is done with hashing filters. This setup was working correctly. But now in the network I

Dear All, I’m working with Fedora Core 3, kernel 2.9.1, MPLS-for-Linux-4.193, and having some problems when create a HTB queue. ALL packets goes to the default queue, they don’t care about any mark or ip field I use to enqueue them. : -/ That’s the deal, all packets that incoming the interface eth2 are classified and have theirs TOS field changed following some qos policy at the PREROUTING

Hello At first I must tell you that I´m a real newbie with Linux (and english as well...) I´m using 2 vlans and shaping works quite well without vlan Now I want to do load balancing at these vlans. Any vlan should get the same minimum/maximum bandwidth of download and use the bandwidth that isn´t used by the other one at the moment. But with vlan the shaping doesn´t work. Can you please tell me

I''ve set up Traffic Shaping on a Linux Router. Using HTB with SFQ, i''m trying to slow down heavy downloading for 20 subscribers over a 2048 kbit downlink. I''m classifying internet related traffic using iptables marking. bri0 is my local lan bridge, receiving egress traffic destined for subscribers. tc qdisc add dev bri0 root handle 1: htb default 2 tc class add dev

I''m streaming audio over a WAN that is 1.5Mbit/s. The audio has to go both ways and can be over tcp or udp. The manufacturers recommend udp as it has less overhead but has a higher chance of dropping out. The audio requires 130-200kbit/s in each direction for a combined 260-400kbit/s. I have two transparent bridges on either side of the WAN to do traffic control. I split it so

Good day all So at log last I did my script We have a 256kbite connection.This scrip runs on my gateway box(the same for script for eth1(ext) and eth0(int) I want to limit all other traffic to 10kbites but when I do it I give me this error: HTB quantum of class 10034 is to small.consider r2q <7>htb*g j=42801780 Here is my script.If you have any Idea to better it let me know.Its a bit from

Hi, I´m shaping traffic using htb on both interfaces, I noticed that shaping download traffic is workinggreat but shaping upload traffic is not working at all (no sent packets, no dropped, no overlimits)I have eth0 facing the backbone and eth1 facing the LAN. Thanks for your help.These are the commands I run:tc qdisc del dev eth0 root tc qdisc add dev eth0 root handle 1 htb default 10 r2q 5 tc

Hi all. I have a bridge running Linux 2.4.24 that I use as a bandwidth manager on a broadband wireless network. I''m using HTB and SFQ to prioritize that share bandwidth on a per-cell basis. My IP tables rules divide the traffic based on IPand traffic type (using layer-7 filter and ipp2p). My goal is to make sure that p2p traffic on the network doesn''t sink all of the

Hi All, I''ve got an interoffice IPSEC VPN in place that I''m trying to give priority to terminal service (tcp 3389) traffic. I''ve created rules at each end, but have hit a bit of a dillemma. As the data is encrypted I must also give highest priority to protocol 50 otherwise the priority is lost as the packet gets encrypted. When I do this however, I can''t

Hello! I have an internet connection of 64kbps garanteed in a channel of 256kbps. On this connection the metropolitan speed is 10Mbps and in the provider''s network the speed is 100Mbps. I have a few clients behind my linux box and i want to set up some limitations because some of them are using it irrational. I am marking the packets with 0 for internet; 1 for metropolitan 2 for

Hi! I''m trying to limit the uplink bandwidth using htb but no packets are overlimit or dropped. :-( My router config: * Linux kernel 2.4.20-pre10 (htb v3.7) with everything built as modules in QoS, iptables in use. * tc binary from htb3.6-020525.tgz * external interface eth0: Internet access, 512 kbit/s uplink speed * internal interface eth1: internal LAN, 100 Mbit/s The hosts in the