similar to: Rules OK (?), no filtering...

Hi folks, I read the fantastic LARTC How-to and after that i tried to limit one host in my LAN for both down-and upload bandwidth usage. I took section 15.9. and added uplink-limiting as I understood it from the previous chapters. Unfortunately it doesn''t work. I ran the script and went to the specified PC, started a download, and watched the rate. The rate was always about 2000 kbit/s,

root@Delta:~# tc filter add dev ppp0 parent 1:1 flowid 1:5 protocol ip Unknown filter "flowid", hence option "1:5" is unparsable root@Delta:~# tc filter add dev ppp0 parent 1:1 classid 1:5 protocol ip Unknown filter "classid", hence option "1:5" is unparsable I don''t understand why it does not work. Can anybody explain me this problem? --

Hi all, I''m having some problems setting up qdiscs on a bridge.The config looks a little like this: ifconfig ifb0 up # Bring up the IFB for this bridge. tc qdisc add dev eth2 ingress tc qdisc add dev eth3 ingress tc qdisc add dev ifb0 root handle 1:0 cbq bandwidth 100Mbit avpkt 1000 cell 8 # Raw qdiscs on each bridge port tc qdisc add dev eth2 root handle 1:0 cbq bandwidth

Hello. In short Linux Advanced Routing & Traffic Control HOWTO''s chapter 15.4. Prioritizing interactive traffic does not help me at all. I have an asymmetric ADSL connection nominal 64Kbit in / 16Kbit out, real (based on bulk transfers measures) 256Kbit/26Kbit. First thing I would like to improve is to keep interactive (ssh) connection fast even if uplink is full. The test I make

Hi all! :) I see that this is partially covered in the mailing list archive but at the moment I can''t find a straight & working answer. I have an imq device with dynamically attacched classes/qdiscs/filters. There is a hashing filter that maps the last octet of an user''s IP address to a class (and associated qdisc). The "empty" filter looks like this: filter

Hi I have been playing with tc. I''m using htb and sfq. I tried to setup shaping of every ip address within a /20. I found that there must be an upper limit of about 2096 on the number of rules (classes, qdiscs or filters). I was testing a /20 which gives 4096 classes, qdiscs and filters. I''m using hashkey to optimize processing of frames. When executing the script below - it

Hi, I think i have made an error with my filters but i can''t find it. We have a site to site tunnel and want to separate the traffic in two queues, http and business. I''m now filtering on protocol 8080 prio 2 and ip range prio 1. As i read the manual i''ve seen that the filters are executed by prio means that all goes trough the buisiness queue because all traffic is

Hi, I''m trying to use prio qdisc with htb, however not the "usual" way (like for example FairNAT). Here is my idea: Root has HTB shaping traffic to link speed -> then goes PRIO queues -> each prio queue has HTB with sublasses for each user, should look like this: 1: htb qdisc | 1:1 htb class

Hello, I''m working on a customized Linux firewall/router for a small/medium ISP (1200 users) we have almost 4 ranges of internal IPs and i want to limit each IP to a certain speed. The problem is that i''m storing all info about the user including IP and bandwidth rates on a MySQL server, then dump all the htb/sfq lines on a file (which takes 3 minutes) and then i run these

Hi all, I wrote new qdisc SRR (Simple Round Robin). This is just another reimplementation of round robin packets distributions. I''m not using SQF/ESFQ source code and algorithms in this scheduler. The main goal of this work is not given multistream download managers give all bandwidth resource. Please testing this: http://mordor.strace.net/sched-srr/ -- /bye

Hi all :) I''ve been using a tc setup for almost two years, but at some point (probably when I switched to kernel 2.6.x, but I''m not sure) it has started making something very weird. For a certain class, the rate is 125000bit and the ceil is 270000bit, but the fastest rate I get is about 75-80000bit, instead of the "promised" 125000, *with no other traffic in

Hi I''m trying to understand this qdisc stats output: #tc -s qdisc ls dev [interface] [..] qdisc htb 1: r2q 10 default 13 direct_packets_stat 38 Sent 3867654734 bytes 7023775 pkt (dropped 4, overlimits 4852340 requeues 0) rate 0bit 0pps backlog 0b 11p requeues 0 [..] In all my qdiscs, I''ve got "rate 0bit". What does it mean ? As you can see, there is some traffic

Hi, here I have another newcomer question :-) in the section 9.6.1 of this how too http://tldp.org/HOWTO/Adv-Routing-HOWTO/lartc.qdisc.filters.html we can read commands about filters : ------------------------------------------ # tc filter add dev eth0 protocol ip parent 10: prio 1 u32 match \ ip dport 22 0xffff flowid 10:1 # tc filter add dev eth0 protocol ip parent 10: prio 1 u32 match \

I downloaded iproute2-2.4.7-now-ss010824.tar.gz and I did patched tc with the htb3.6_tc.diff from htb3.6-020525.tgz and when I try to use a htb script I get just errors. I did not patch the kernel, since I use kernel 2.4.21 and I saw on - HTB Homepage that I need to patch it only if I run version 2.4.20 or earlier. Do also need the kernel patch ? Or maybe is something else wrong? RTNETLINK

We have a Linux box that is acting as the gateway to the internet for about 400 people, typically there are not more then 50 of them using the internet at any given time. We would like to provide different levels of access to different users. For example 128kbps to some users and 256kbps to others. We have considered creating a class and qdisc for each user (using htb) however we don''t

Le 26 juil. 07 à 13:55, Georgi Alexandrov a écrit : > Vincent Dautremont wrote: > >> Hi, >> here I have another newcomer question :-) >> in the section 9.6.1 of this how too >> http://tldp.org/HOWTO/Adv-Routing-HOWTO/lartc.qdisc.filters.html >> we can read commands about filters : >> ------------------------------------------ >> >> # tc

hello to all i''m trying to set a filter but doesn''t want to work. i''ve set ut the qdiscs and the classes like this : tc qdisc add dev ppp0 root handle 1: htb default 20 tc class add dev ppp0 parent 1: classid 1:1 htb rate 120kbit tc class add dev ppp0 parent 1:1 classid 1:20 htb rate 30kbit ceil 120kbit tc class add dev ppp0 parent 1:1 classid 1:21 htb rate 30kbit ceil

Hi everyone, This is on a linux box, ingress (eth1) at 100Mb/s and egress (eth0) at 10Mb/s. The purpose is to test CBQ Here is my script ------------------------------------------------------------------- # Root qdisc tc qdisc add dev eth0 root handle 1:0 cbq bandwidth 9Mbit \ avpkt 1000 cell 8 # Classes tc class add dev eth0 parent 1:0 classid 1:1 cbq bandwidth 9Mbit \ rate 5Mbit weight

Hey, I have a problem adding a filter matching anything, here is my setup: ############### tc qdisc add dev eth0 handle 1: root prio tc qdisc add dev eth0 parent 1:1 handle 10: pfifo tc qdisc add dev eth0 parent 1:2 handle 20: tbf latency 50ms rate \ 128kbit burst 256kbit tc filter add dev eth0 protocol ip parent 1:0 prio 1 handle 666 fw \ flowid 1:2 tc filter add dev eth0 protocol ip parent

For simplicity, I tried this: tc qdisc add dev eth0 root handle 1: prio tc qdisc add dev eth0 parent 1:1 handle 10: sfq perturb 10 tc qdisc add dev eth0 parent 1:2 handle 20: sfq perturb 10 tc qdisc add dev eth0 parent 1:3 handle 30: sfq perturb 10 tc filter add dev eth0 protocol ip parent 1: prio 2 flowid 1:1 The last line prints: Unknown filter "flowid", hence option "1:1"