similar to: RE: service-based and ip-based shaping

Hello guys, I need to accomplish 2 tasks with one Linux router: 1) Shape the traffic based on services (e.g. HTTP max 512 kbps, P2P max 128 kbps - with a lower prio, etc) 2) After I have classified the traffic based on services, I want to pass it to the clients with different rates/ceils (one client will get 8/128 kbps, other 8/64 kbps, etc). If all the users are downloading via P2P I do not

-------------- next part -------------- An embedded message was scrubbed... From: Vinod Chandran <vinod_chandran@multitech.co.in> Subject: Re: [LARTC] sercice-based and ip-based shaping Date: Tue, 02 Aug 2005 10:36:00 +0530 Size: 3441 Url: http://mailman.ds9a.nl/pipermail/lartc/attachments/20050802/44a5f54e/LARTCsercice-basedandip-basedshaping.eml

i''m trying to limit upload and download but something is wrong(it is about NAT) i will post here my "script" maybe someone could tell me what is wrong my kernel(2.6.9) is patch with imq(linuximq.net) and my iptables(1.2.11) also #flush tc qdisc del dev eth0 root tc qdisc del dev eth1 root tc qdisc del dev imq0 root tc qdisc del dev imq1 root ifconfig imq0 down

Hello to all people there . Can i guarantee ICMP respond time no metter how loaded is internet line . i have typical NATed enviroiment like External IP |linux router| LAN - 192.168.0.0/24 i have example setup with IMQ but is it possible to be done also if i attache htb to eth0 and eth1 for example . if i start shaper ping i better that without shaper but it''s not guarantted i mean

Hi All, I''m trying to create a contended section of bandwidth using IMQ. I have the imq0 device up and running, with traffic passing through it. Firstly, I need to throttle the entire device imq0 to 2mbit/s. I would then like to add throttle rules for individual IP addresses, allowing them to pass up to 512kbit/s each, as long as imq0 has not reached its 2mbit/s. The configuration

Hello, I wrote a simple traffic shaping script (below) that should have allowed me to shape my internet traffic a bit (ppp0 - adsl 128kbit/64kbit; local interface eth0). The script works only partially - the speed is being limited but too much. Without running this script my download rate is about 10kBytes (with second computer also downloading at about 6kBytes). After running it my download speed

Hi, i am running imq + htb on my router , the situation is like this eth0 = uplink to my provider eth1 = 1st customer eth2 = 2nd customer eth3 = 3th customer eth0 has limit 512 and i want to share this between eth1 eth2 and eth3 , but not working , this is the script i used, \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ #!/bin/sh

Hello, I''m trying to get my shaper to work, but have only a partial success. Can someone help me with that. My setup unfortunately is not so trivial, but I think some people could have similar one... 1. There is a router connected to the internet line via interface eth0 2. There are users connected to the router via two interfaces : eth1 and wlan0 3. All users are assigned private IP

I''m using HFSC to limit bandwidth for our wireless customers. However, I''d also like the bandwidth prioritized based on packet type. This is what I''m trying right now, and I''d just like some input from anyone out there knowledgeable in this on whether it does what I want it to do: Eth1 -> HFSC ........|-> HFSC (User1) (Min 512 Kb, Max 1024 Kb, Burst 1536

On 2/19/07, Salatiel Filho <salatiel.filho@gmail.com> wrote: > Well , thanks to imq all my client machines are now shaped and > everything is great ... > But now i have a doubt , is there a way to shape the traffic that goes > to the route [doing a wget from the router for example ]? > > > I have a PREROUTING IMQ0 and a POSTROUTING IMQ1 , everything is > working like

Hi I have the following problem: I''ve created qos script which shapes traffic on outgoing interface eth1. More - less it looks like this : ------------------------CUT------------------------------------------------------ #root qdisc and class for eth1 $tc qdisc add dev eth1 root handle 1:0 htb default 19 $tc class add dev eth1 parent 1:0 classid 1:1 htp ratel ${CEIL_UP}kbit ceil

Hello, I am trying to shape p2p trafik to 256kbps on my dsl line. I wrote this set of commands: DEV=eth2 ip link set imq0 up tc qdisc add dev imq0 root handle 1:0 htb default 21 r2q 2 tc class add dev imq0 parent 1:0 classid 1:1 htb rate 530kbit tc class add dev imq0 parent 1:1 classid 1:20 htb rate 530kbit ceil 530kbit prio 0 tc class add dev imq0 parent 1:1 classid 1:21 htb rate 64kbit

Hi folks, I have three network cards on my Slackware box and eth0 and eth1 are for two Internet connections. They have imq0 and imq1. All traffic shaping works fine. Internal eth2 does no traffic shaping. But recently I have put two OpenVPN tunnels (tun devices) and both work via eth0. So my question is - how to shape the traffic on these tun0 and tun1 devices? Thanks Remus

Hello, I''ve just recently started to use IMQ and I got puzzled after seeing the imq usage example on the linuximq.net site: It was something like this: tc qdisc add dev imq0 handle 1: root htb default 1 tc class add dev imq0 parent 1: classid 1:1 htb rate 1mbit tc qdisc add dev imq0 parent 1:1 handle 10: htb default 5 tc class add dev imq0 parent 10: classid 10:1 htb rate 256kbit

On my debian woody (kernel 2.4.31) the tcpdump doesn''t work with imq0 devices. If I try to tcpdump imq devices there is no packet seen: [...] rt1:~# tcpdump -n -i imq0 Warning: arptype 65535 not supported by libpcap - falling back to cooked socket tcpdump: WARNING: imq0: no IPv4 address assigned tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on

Hello, I have a serious problem with HTB which I wasn''t able to solve myself. I run a masquerading router with ppp0 as interface to the Internet. Three clients need to share a downstream of 1 MBit, which I want to divide with tc. When I see a packet being forwarded to one of these clients, I give it the appropriate unique mark: iptables -t mangle -A FORWARD -d 192.168.34.141 -j MARK

Hi all, my IMQ device works OK (thanks to Andy Furniss), but now I''ve problems to attach the traffic in the qdisc''s. This is my conf: ----------------------------------------------------------------------- INET | |eth0 300Kbps ROUTER (NAT) |eth1 | LAN ----------------------------------------------------------------------- MAX=300 tc qdisc add dev imq0 root handle 1: htb

Hi folks, I`ve a problem to use HTB and SFQ. The first script, below, to show a simple configuration, does work fine...!!! But, in the second example, does not work, becouse i put more code to clasify the traffic by protocol, http and ftp in this case. Somebody can tell me the errors? Thx, in advance.- NOTICE: IMQ device is to asociate with ETH1 my external iface. SCRIPT que funciona:

Hello, some days ago, I was asking for help here about not able to do anything when I had bittorrent running, I will post the problem here: I''m using ipp2p to mark p2p packets, and then send them with -j CLASSIFY to the correct HTB class, I see traffic in the class when I start azurerus, and traffic does get shaped, but then I''m still not able to surf the web nor chat nor