similar to: HTB Rate and Prio

Hi again, I keep posting about my problem with HTB -> http://mailman.ds9a.nl/pipermail/lartc/2005q3/016611.html With a bit of search I recently found the exact same problem I have in the 2004 archives with some graphs that explain it far better than I did -> http://mailman.ds9a.nl/pipermail/lartc/2004q4/014519.html and http://mailman.ds9a.nl/pipermail/lartc/2004q4/014568.html

Hi, I have a default class for my un-marked traffic (prio 5) and a prio 0 class for the important stuff, but I do not understand why my download traffic is duplicated in both. It work fine for my upload traffic (same setting except the red class but I have the same result if I create an esfq instead). Any comments/information will be appreciated. Below my config : tc commands from my scirpt :

Dear All, I''m using the kernel 2.6.6, iproute2-2.4.7.20020116, iptables v1.2.9, and gentoo. I have a leased-line 64 kbps. I can see the counter works in iptables, but in the htb, it doesn''t go to the right class (it always go to the default class). Any help will be appreciated here''s my htb conf #!/bin/bash tc qdisc del dev eth1 root tc qdisc add dev eth1 root

dear All, I'm a new student and my job is too shapping bandwith for our campus faculty network. I want to implement htb with Redhat-9.0 distro. does this distro kernel support htb and tc good ? or i should apply some patch or upgrade kernel ? regards reza

Hi all. I''m going on my 3rd week trying to get a simple traffic shapping to work the right way :( !! My goal it to shape the traffic coming from one machine (pc1) to another machine (pc2) throught the "eth0" interface. My test configuration is as follows: PC1   IP: 192.168.105.237   Mask: 255.255.255.0   OS: Red Hat Linux Kernel 2.4.20-8   Rules:

With the below script, whenever I ping 10.0.16.10 (which matches the only filter I have), traffic still get''s sent to the default 1:2 class instead of 1:1 and I don''t know why... Any hints? (kernel 2.6.12, iproute2-2.6.15) tc qdisc del dev eth0 root > /dev/null 2>&1 tc qdisc add dev eth0 handle 1: root htb default 2 tc class add dev eth0 classid 1:1 parent 1: htb rate

Hello! I need to switch from htb2 to htb3, because of speed issues (for me, htb2 is unable to handle more then 100mbit duplex with ~550 classes), kernel profiling shows htb_dequeue_prio at 1st place with 3x isolation. So, I''ve moved from 2.4.19 to 2.4.25 kernel (hi-pac for classification/marking and htb3 for queueing), and traffic rate drop from 100 to 20mbit. What can be wrong? The

Hi, What exactly are the "tokens"? I thought each token allowed the sending of one byte, that tokens are stored in a bucket that can hold a max of "burst" tokens, and that this bucket is filled with tokens at "rate". But theory does not seem to explain the "tc -s .." output in the examples below. And I can''t figure out why or how... #tc qdisc

Sorry I pressed the wrong key and sent the message too early... > -----Ursprüngliche Nachricht----- > Von: Philipp Leusmann [mailto:philipp.leusmann@rwth-aachen.de] > Gesendet: Mittwoch, 8. November 2006 12:53 > An: ''lartc@mailman.ds9a.nl'' > Betreff: Why did I need strange ceiling settings? > > Hi all, > > I recently installed traffic shaping on my

Hi folks...!!! I need to generate qdisc statistics to show my 4 class (10, 20, 30, 40), i`ve all working with HTB and so on, but i need to graph this results e.gwith RRDTOOL. I found a script made in perl, that can to graph my 4 class, but i need to know which IP address on my LAN are using the bandwidth too, in other hand i need to classify the traffic by IP to show. This is an out of my

Hi all, Can you tell me where is the documentation for the new IFB (implemented in kernels > 2.6.16). Thanks in advance! Nikolay

I''m trying to shape traffic on a Devil-Linux box. This note was originally sent to their maillist, because the LARTC list appears to have been down for the past few days. My mailbox was just flooded with a half dozen or so confirmation requests in response to my repeated attempts to subscribe to this list. ---------- Forwarded message ---------- From: drew einhorn

Hello. I have a linux server connected to a gigabit lan, and though that lan to a 768kbps/768kbps DSL modem. I''m trying to shape my webserver running on port 80/443 down to 512kbps, while leaving all other ports alone. The current configuration script that I''m using is as follows: tc qdisc del dev eth0 root tc qdisc add dev eth0 root handle 1: htb default 99 tc class add dev

Hi All, I am using the script below to limit download rates and manage traffic for a certain IP address and testing the results using iperf. The rate that iperf reports is much higher than the rate I have configured for the HTB qdisc. It''s probably just some newbie trap that''s messing things up but I''m buggered if I can see it. The following script is run on the

Hi guys, i have a little doubt ; I have eth0 ethernet and eth1 wireless , and they are bridged in br0 Is there any difference in the behavior between do tc qdisc add dev br0 root sfq OR tc qdisc add dev eth0 root sfq && tc qdisc add dev eth1 root sfq -- []''s Salatiel "O maior prazer do inteligente é bancar o idiota diante de um idiota que banca o

I have to match my packets based on MAC address, which I cannot do in the POSTROUTING chain, so I do it in PREROUTING using MARK. Then, I match on the MARK in the POSTROUTING chain to do a CLASSIFY. But this does not seem to work: wireless-r1 bwlimit # iptables -L -v -n -t mangle Chain PREROUTING (policy ACCEPT 3353K packets, 941M bytes) pkts bytes target prot opt in out source

Hi Here is something that worked with with 2.6.10-1.771_FC2smp and stopped working when I upgraded to 2.6.16-1.2069_FC4smp. These are fedora kernels and the network controller is an Intel Gbit (e1000) running a 100 Mbps Full Duplex. Don''t know how or if this matters but the 2.6.10 kernel has CONFIG_X86_HZ=1000 and the 2.6.16 has CONFIG_HZ=250 The idea is to just shape to , say 2Mbit, a

I wrote a Perl script to poll `tc` for traffic control statistics (just bytes presently) for leaf qdiscs. The information is fed to either RRDTool or Munin[2], depending on what parameter is passed to the script. If the option for a RRD database is used, graphs[3][4] are written to disk for each ten second polling interval. If invoked via Munin[2], it handles graphing and samples at five

Hi I have setup iproute2 and need a bit of help reading the stats from it ===== output qdisc htb 1: r2q 10 default 20 direct_packets_stat 0 ver 3.17 Sent 547326809 bytes 1342627 pkts (dropped 9303, overlimits 2817572 requeues 0) backlog 46p qdisc sfq 10: limit 128p quantum 1514b flows 128/1024 perturb 10sec Sent 41874343 bytes 730889 pkts (dropped 0, overlimits 0 requeues 0) qdisc sfq

Hi, machine: AMD K6 200 MHz Linux distribution: Mandrake 8.1 kernel: compiled 2.4.21 applied this: #define PSCHED_CLOCK_SOURCE PSCHED_CPU in file linux/include/net/pkt_sched.h bevore compiled the kernel (described on http://www.docum.org/stef.coene/qos/faq/cache/40.html) bandwitch on eth0: 128kbit The most simple configuration - 122kbit guaranted for WWW (sport 80) and