similar to: tcpdump not working with imq0 devices

mdew:~# tc qdisc add dev imq0 handle 1: root htb default 12 r2q 1 Cannot find device "imq0" mdew:~# lsmod Module Size Used by Not tainted ipt_REDIRECT 728 0 (autoclean) ipt_MARK 728 2 (autoclean) iptable_mangle 2100 1 (autoclean) ipt_REJECT 2712 4 (autoclean) iptable_filter 1672 1 (autoclean)

I have had a web server listining sql-1433, www 80, ftp-21 using proxy arp with sub-netting in a three interface DMZ. All these ports are in the rules file as ACCEPT. With one exeception that 1433 allows a few host from the net. 21 and 80 allow all net to dmz connections. The policy is DMZ to net ACCEPT This has been working great for about a month or more until I rebooted the

hi all, i want to try htb3 with imq downloaded & patched imq & htb3 with kernel-2.4.18 on rh7.2 but got STUCK on step 1 :( this are what i did can anyone guide me what went wrong on the first step itself !! [root@cab1 root]# modprobe imq numdevs=1 modprobe: Can''t locate module imq [root@cab1 root]# [root@cab1 root]# tc qdisc add dev imq0 handle 1: root htb default 1 Cannot find

We have a (supposedly) quite standard setup: 2 Dom0 with drbd-on-lvm and a bunch of DomU, on Quad Xeon Dell servers. We tried with both sid-based and etch-based (+ 3.1 xen hypervisor and drbd 8 from backports.org ) Dom0, and quite consistently have "kernel: invalid opcode: 0000 [1] SMP" errors which freezes Dom0 (during lasts tests a simple start-and-stop loop of 10 DomU can trigger

Hi all. On Sep 26th I decided to try and get ipp2p working on my machine that acts as a gateway for my Internet connection. This machine is running Debian. I performed the install by doing the following steps: - I installed the Debian package called linux-source-2.6.22 for my Linux kernel source and unpacked the resulting tar.bz2 file. - From the netfilter.org site I downloaded the following

Hello, I run Shorewall 2.0.3a backport on a debian woody box (with 2.4.18 homemade kernel). When I start shorewall I got the following errors. Oct 30 11:13:12 fwr modprobe: modprobe: Can''t locate module ipt_conntrack Oct 30 11:13:17 fwr modprobe: modprobe: Can''t locate module ipt_pkttype Oct 30 11:13:18 fwr modprobe: modprobe: Can''t locate module ipt_pkttype Oct 30

a.shubnik@btis.by wrote: > Hello Tom! Aleksandr, In the future, please don''t send your Shorewall support requests directly to me. Please see http://www.shorewall.net/support.htm: > I try to start last version of shorewall-4.0.2 under openvz environment > in virtual server and get follow error messages: > > gate ~ # shorewall check > Checking... > >

Hi, I am struggling to get rid of a conflict on DELL 2800 : PCI Parity error (EB113 on the display) I am learning linux and asterisk as I go along, there might be obvious things I should know, but bear with me. >From demsg below my 2 digium cards installed are listed (no config or connections done to digium cards yet), the conflict is with the TDM400P card, without that card, in any slot, no

Does anyone keep a known telemarketer caller id database? If not has anyone proposed an Asterisk community project to share this information? Sort of a nation wide blacklist so Asterisk'ers can cut down on the garbage calls... -------------- next part -------------- An HTML attachment was scrubbed... URL:

zaprtc 'load' is failing on my machine (the make was fine, same output as other posts to this list) [xxx@xxx zaptelrtc]# make load sync modprobe zaptel insmod ./zaprtc.o ./zaprtc.o: init_module: Input/output error Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or

Hi folks, I`ve a problem to use HTB and SFQ. The first script, below, to show a simple configuration, does work fine...!!! But, in the second example, does not work, becouse i put more code to clasify the traffic by protocol, http and ftp in this case. Somebody can tell me the errors? Thx, in advance.- NOTICE: IMQ device is to asociate with ETH1 my external iface. SCRIPT que funciona:

Hi ! I have a single host which is connected via an 512kbit ADSL link to the n= et. I quite often use some realaudio application that uses some bandwidth = and I want to avoid other traffic to scale that bandwidth down. So I used = some classes (with htb) on imq0 device and applied some filters and it see= ms to work in most cases. However, there are some sites with which downloa= d is

Hi All, I''m trying to create a contended section of bandwidth using IMQ. I have the imq0 device up and running, with traffic passing through it. Firstly, I need to throttle the entire device imq0 to 2mbit/s. I would then like to add throttle rules for individual IP addresses, allowing them to pass up to 512kbit/s each, as long as imq0 has not reached its 2mbit/s. The configuration

Hi all, my IMQ device works OK (thanks to Andy Furniss), but now I''ve problems to attach the traffic in the qdisc''s. This is my conf: ----------------------------------------------------------------------- INET | |eth0 300Kbps ROUTER (NAT) |eth1 | LAN ----------------------------------------------------------------------- MAX=300 tc qdisc add dev imq0 root handle 1: htb

hello... 1. Is it possible using u32 to filter marked packets? I have found only documents to fw filter to filter marked packets... 2. If u32 cannot filter marked packets is it possible to use fw and u32 together? I wanted to filter packets marked by iptables by fw, and packets depended on ip destination, src and others by u32, but something goes wrong :( the filters configuration is: $TC

Hello I have 2 class-B networks (172.22.0.0/16 and 172.23.0.0/16, over 130k of ip''s) and need to setup traffic tbf shapers with 64kb/s for each ip from 172.22.0.0/16 and 128kb/s for each ip from 172.23.0.0/16 just read lartc and don''t understand how to use u32 for decreasing number of rules and hashing

Hello, I have a serious problem with HTB which I wasn''t able to solve myself. I run a masquerading router with ppp0 as interface to the Internet. Three clients need to share a downstream of 1 MBit, which I want to divide with tc. When I see a packet being forwarded to one of these clients, I give it the appropriate unique mark: iptables -t mangle -A FORWARD -d 192.168.34.141 -j MARK

I have: tc qdisc add dev imq0 root handle 1: htb default 30 tc class add dev imq0 parent 1: classid 1:1 htb rate 512kbit ceil 512kbit tc class add dev imq0 parent 1:1 classid 1:30 htb rate 64kbit ceil 512kbit then: iptables -t mangle -A PREROUTING -i ppp0 -s 192.168.2.2 -j IMQ --todev 0 tc class add dev imq0 parent 1:1 classid 1:22 htb rate 64kbit ceil 128kbit tc filter add dev imq0 protocol

this : iptables -A FORWARD -i internal-interface -j ACCEPT iptables -A FORWARD -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -j DROP doesn''t seem to work for active-ftp .. i even manualy loaded ip_conntrack_ftp but as u see it is unused : # lsmod Module Size Used by Not tainted ip_conntrack_ftp 4272 0 (unused) iptable_nat

https://bugzilla.netfilter.org/cgi-bin/bugzilla/show_bug.cgi?id=68 ------- Additional Comments From laforge@netfilter.org 2003-03-20 10:55 ------- This looks strange. The BUG in slab.c tells us that there is a GFP_ATOMIC missing. This means that we are allocating kernel memory from softirq context with only GFP_KERNEL. If I understand your backtrace correctly, what happens is: - you are