similar to: UDP transfer speed exceeding the ceil by about 4x

What''s going on here? I''m spewing UDP traffic at this thing, and it is exceeding the ceil. Anyone know how to fix this? class htb 1:613 parent 1:5 leaf 613: prio 6 quantum 2560 rate 20480bit ceil 103360bit burst 15Kb/8 mpu 0b overhead 0b cburst 1728b/8 mpu 0b overhead 0b level 0 Sent 16591370 bytes 4159 pkt (dropped 39449, overlimits 0 requeues 0) rate 412384bit 6pps backlog 0b

What''s going on here? I''m spewing UDP traffic at this thing, and it is exceeding the ceil, (i watched it for a few minutes, it didn''t slow down). Anyone know how to fix this? class htb 1:613 parent 1:5 leaf 613: prio 6 quantum 2560 rate 20480bit ceil 103360bit burst 15Kb/8 mpu 0b overhead 0b cburst 1728b/8 mpu 0b overhead 0b level 0 Sent 16591370 bytes 4159 pkt (dropped

I''m using a fairly large number of classes, andf borrowing is not working as expected... I''ve called this setting it up on an IMQ device with speed 1200/256 on a 1536/384 line. I''m then throwing a UDP data transfer at it that gets tossed in one of the class under parent 1:6. The classification is working fine, but when I try to ping out, ping times are in the 900ms

Hi Guys, I want to create multiple virtual interfaces on a system running linux 2.6. The main requirment being, to assign unique MAC address fo each of the virtual interfaces. I need to know, if this is possible and will really appriciate if someone can provide me pointer in this direction. Thanks a lot. R. Singh _______________________________________________ LARTC mailing list

Hello, I have a serious problem with HTB which I wasn''t able to solve myself. I run a masquerading router with ppp0 as interface to the Internet. Three clients need to share a downstream of 1 MBit, which I want to divide with tc. When I see a packet being forwarded to one of these clients, I give it the appropriate unique mark: iptables -t mangle -A FORWARD -d 192.168.34.141 -j MARK

Hi, Does anyone tried to get ipip or gre tunnel behind NAT environments. ? i''m trying to make both side tunneling with ipip or gre with private address just like belows.. A -------------------FIRWWAL -------------------INET ------------------- B PRIVATE PUBLIC PUBLIC (10.100.0.1) (211.xxx.xxx.xxx) (

Hello, i have a htb setup where the root and (nearly) all child classes has a ceil rate with max up from my adsl line. But the root class don''t reach the ceil value but some childs are get a huge backlog. My setup: (tc -d class show dev ppp0) [cleaned a bit] ******************************************************** class htb 1:1 root rate 576000bit ceil 576000bit burst 30Kb/8 cburst

We run a Hosting farm behind a bridge/iptables firewall setup running Gentoo with kernel 2.4.20-gentoo-r6, connected to a dual 15Mbps international internet pipe / , as this: Net Pipe --------- eth1 Bridge/Firewall eth0 -------- Internal Hosting Network lately we have been looking at htb to somehow control excessive usage from the users behind, but in our implementation there seems to be an

Hi I have tested with FC3 but iam not able get any good results on that. in the list some one recomend me that > 3.17 HTB should work I saw latest FC4 test2 has the HTB 3.17 with iptables 1.3.0 i have install in my P4 box, and trying to test when iam uploading its working perfect, but when iam downloading its going to default class can some one experinced the same problem below is the my

Hi When I list all the qdisc with tc command it is not possible to see the parent of the qdisc. An example by the book. # tc qdisc add dev eth0 root handle 1: htb default 30 # tc class add dev eth0 parent 1: classid 1:1 htb rate 6mbit burst 15k # tc class add dev eth0 parent 1:1 classid 1:10 htb rate 5mbit burst 15k # tc class add dev eth0 parent 1:1 classid 1:20 htb rate 3mbit ceil 6mbit

Hello, after spending several hours reading archives, I decided to write new post. I successfully set up packet classification, made some basic HTB setup, made some simple graphical representation from HTB statistics data... BUT, I cannot figure out how to refine HTB to get this behaviour: I need that class "p2p" should be the last one to get some link capacity. If I set both RATE

Hi. I did send this to `jaazz@post.cz'', but I suspect the list is a more appropriate/useful place for it. It''s a question about Michal Charvat''s QoS extension to Net-SNMP. When I look at the MIB entries for the QoS handles, I get something like this - enterprises.qos.qosObjectTable.qosObject.qosHandle.0.0 = Gauge32: 0

Eric, I''ve attached the output from the command you requested below. I''m using kernel 2.6.17.12 and tc version ss060323. I''m have a nforce4 onboard giggabit controller using the forcedeth driver, if that makes a difference. Charlie, I''ll take a look at the Apache model for throttling, thanks. I was going for tc because was going to try to add additional

An earlier exchange about someone seeing the rate larger than the ceiling is posted below. Andy explained the reason for the "above ceiling" rate in Daniel''s output . . . but I just saw an example that doesn''t fit. >> tc output >> class htb 1:14 parent 1:1 leaf 14: prio 1 quantum 3072 rate 256000bit ceil 282000bit burst 1820b/8 mpu 0b overhead 0b

Hello! I need to switch from htb2 to htb3, because of speed issues (for me, htb2 is unable to handle more then 100mbit duplex with ~550 classes), kernel profiling shows htb_dequeue_prio at 1st place with 3x isolation. So, I''ve moved from 2.4.19 to 2.4.25 kernel (hi-pac for classification/marking and htb3 for queueing), and traffic rate drop from 100 to 20mbit. What can be wrong? The

In this simple htb setup: # tc -s -d class ls dev eth0 class htb 1:1 root rate 300000bit ceil 300000bit burst 1749b/8 mpu 0b overhead 0b cburst 1749b/8 mpu 0b overhead 0b level 7 Sent 13171835 bytes 13169 pkt (dropped 0, overlimits 0 requeues 0) rate 45848bit 10pps backlog 0b 0p requeues 0 lended: 5272 borrowed: 0 giants: 0 tokens: -84429 ctokens: -84429 class htb 1:2 parent 1:1 prio 0

Hi, I have a box set up to distribute load over 4 satellite connections. I cannot use Instant Messenger programs with it as it stands, I believe that using iproute2, the path to the server is not being locked to one interface, so the IM servers are getting user traffic from multiple IPs. When I set just one default gateway, IMs work great. When I use the scope global/nexthop method of load

Hello, I use HTB with linux-2.4.20-ac1 and iptables-1.2.7a (pathced for IMQ). I configured one HTB qdisc on an IMQ device. This qdisc has some classes (about 5) and all of the classes has qdisc pfifo. I sometimes got out from my linux (while I was working) and I found in logs: Dec 4 11:49:27 core kernel: HTB init, kernel part version 3.7 Dec 4 11:49:28 core kernel: HTB: quantum of class

tc qdisc add dev eth0 root handle 1: htb default 12 tc class add dev eth0 parent 1: classid 1:10 rate 30kbps ceil 100kbps burst 2k tc class add dev eth0 parent 1: classid 1:11 rate 10kbps ceil 100kbps burst 2k tc class add dev eth0 parent 1: classid 1:12 rate 60kbps ceil 100kbps burst 2k tc filter add dev eth0 protocol ip parent 1:0 prio 1 u32 match ip src 172.16.11.2 flowid 1:10 i login

Martin Devera wrote: > If you read the manual, the algorithm will not work correctly > with {,c}burst < MTU ... > devik > I just tried to change {,c}burst to 1600, or leaving them by default but no visible result. here is the latest tc -s -d class show dev eth0 class htb 1:101 parent 1:1 prio 0 rate 40Kbit ceil 40Kbit burst 1599b/8 mpu 0b cburst 1599b/8 mpu 0b quantum 512 level