similar to: Htb queueing problem

Hi, My home setup is as following: - 1024/128 kbit ADSL - FC3 I set up HTB to prioritize traffic. I am not very pleased with the obtained results. The scope of my setup is to have some ssh sessions with remote servers while browsing websites and running aMule Nothing complicated (I think... ;). The very high priority traffic (ssh), gets stuck when I start aMule and make an FTP download.

Hi! I''m trying to limit the uplink bandwidth using htb but no packets are overlimit or dropped. :-( My router config: * Linux kernel 2.4.20-pre10 (htb v3.7) with everything built as modules in QoS, iptables in use. * tc binary from htb3.6-020525.tgz * external interface eth0: Internet access, 512 kbit/s uplink speed * internal interface eth1: internal LAN, 100 Mbit/s The hosts in the

Hello. The problems are: 1. Using HTB I get negative values for tokens and ctokens in tc -s output, for example: mich:~# tc -s -d class show dev eth0 class htb 1:11 parent 1:1 prio 1 quantum 1024 rate 8Kbit ceil 23Kbit burst 1609b/8 mpu 0b cburst 1628b/8 mpu 0b level 0 Sent 0 bytes 0 pkts (dropped 0, overlimits 0) lended: 0 borrowed: 0 giants: 0 tokens: 1287999 ctokens: 453286 class htb 1:1

Eric, I''ve attached the output from the command you requested below. I''m using kernel 2.6.17.12 and tc version ss060323. I''m have a nforce4 onboard giggabit controller using the forcedeth driver, if that makes a difference. Charlie, I''ll take a look at the Apache model for throttling, thanks. I was going for tc because was going to try to add additional

Dear All, I''m using the kernel 2.6.6, iproute2-2.4.7.20020116, iptables v1.2.9, and gentoo. I have a leased-line 64 kbps. I can see the counter works in iptables, but in the htb, it doesn''t go to the right class (it always go to the default class). Any help will be appreciated here''s my htb conf #!/bin/bash tc qdisc del dev eth1 root tc qdisc add dev eth1 root

Hello! I need to switch from htb2 to htb3, because of speed issues (for me, htb2 is unable to handle more then 100mbit duplex with ~550 classes), kernel profiling shows htb_dequeue_prio at 1st place with 3x isolation. So, I''ve moved from 2.4.19 to 2.4.25 kernel (hi-pac for classification/marking and htb3 for queueing), and traffic rate drop from 100 to 20mbit. What can be wrong? The

Hi everyone, My HTB script is showing me those "r2q change" warnings. I read that I should test with r2q values to gain accuracy and stop the warnings but I made some tests with r2q and with burst and I still get the warnings. Any ideas on this issue will be very helpful. The script seems to be working as the bandwidth for the IPs is being shaped. The NIC works at 100mbit and the

Hello, 1. I currently have a 128kbps cable link to the internet..and I''m sharing this connection with others. I''ve made the following script(for alocating bandwidth depending on the services used: browsing, squid, games like counter-strike, icmp, ssh), which unfortunately isn''t working very well as the response times I''m getting upon pinging the server

Hi all, I have been getting some strange results with HTB in kernel 2.6.11, and was wondering if anybody could give me some advice. Also, if someone could direct me to the changelog for the recent versions so I can see if it is worth upgrading? Anyway, the problem can best be summed up by looking at the output of ''tc -s -d class show dev eth0''. Some of the relevant results

Hi I have setup iproute2 and need a bit of help reading the stats from it ===== output qdisc htb 1: r2q 10 default 20 direct_packets_stat 0 ver 3.17 Sent 547326809 bytes 1342627 pkts (dropped 9303, overlimits 2817572 requeues 0) backlog 46p qdisc sfq 10: limit 128p quantum 1514b flows 128/1024 perturb 10sec Sent 41874343 bytes 730889 pkts (dropped 0, overlimits 0 requeues 0) qdisc sfq

Hello, I use HTB with linux-2.4.20-ac1 and iptables-1.2.7a (pathced for IMQ). I configured one HTB qdisc on an IMQ device. This qdisc has some classes (about 5) and all of the classes has qdisc pfifo. I sometimes got out from my linux (while I was working) and I found in logs: Dec 4 11:49:27 core kernel: HTB init, kernel part version 3.7 Dec 4 11:49:28 core kernel: HTB: quantum of class

Hi I have tested with FC3 but iam not able get any good results on that. in the list some one recomend me that > 3.17 HTB should work I saw latest FC4 test2 has the HTB 3.17 with iptables 1.3.0 i have install in my P4 box, and trying to test when iam uploading its working perfect, but when iam downloading its going to default class can some one experinced the same problem below is the my

Hello, I have begun to use the tc scripts since 2 weeks ago, so I am beginner. I am trying to divide my bandwidth in 4 independent ones. Each of these sub-bandwidths is assigned to 4 different groups of ip. Bandwidth sharing is allowed. I put a Linux with two Ethernet card between the router and the LAN. Eth1 is the card connected to the router and eth0 is the one connected to the LAN. My ISP

I have successfully implemented a QoS system using HTB on a 2Mb/s leased line and it works very well, but I would like to be able to graph the three pipes to see what they are doing, eg: using MRTG or similar. Has anyone any experience or examples of how to do this please? Thanks, Chris _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl

//Just to not forget eth0 is WAN and eth1 is LAN . The box is NATing my lan. I configured tcng to shape both download and upload and i got connection loss again. Maybe it is my script fault or it is something bad with packets marking . this is how i mark outgoing packets iptables -t mangle -A MYSHAPER-OUT -p tcp -s 192.168.1.23 -j MARK --set-mark $ip and this part of my script which is intented

Dear all, I''m having real problems getting tc to do anything useful at all. I''m also under pressure to get this fixed before the students start arriving later this month (I work in a university). In short, I want each IP address to be hard limited to 128kbit down, 64kbit up, never to be allowed more bandwidth than this. It is also important that the latency remains

Hi, I wanted to implement some QOS on my Linux Box with HTB, but after some time spend on the configuration and tests, I still don''t manage to have some correct results. Here are the details : -ROOT 2000 kbits -HIGHPRIO SUBCLASS 50 kbits prio 0 -SUBCLASS1 750 kbits prio 1 -SERVICE1 250 kbits prio 1

Hi, machine: AMD K6 200 MHz Linux distribution: Mandrake 8.1 kernel: compiled 2.4.21 applied this: #define PSCHED_CLOCK_SOURCE PSCHED_CPU in file linux/include/net/pkt_sched.h bevore compiled the kernel (described on http://www.docum.org/stef.coene/qos/faq/cache/40.html) bandwitch on eth0: 128kbit The most simple configuration - 122kbit guaranted for WWW (sport 80) and

hi there, this is my 1st message in the list. I would like to use this wondershaper.htb to limit the bandwith usage at home. My kernel config is: # QoS and/or fair queueing # CONFIG_NET_SCHED=y CONFIG_NET_SCH_CBQ=y CONFIG_NET_SCH_HTB=y CONFIG_NET_SCH_CSZ=y CONFIG_NET_SCH_HFSC=y CONFIG_NET_SCH_PRIO=y CONFIG_NET_SCH_RED=y CONFIG_NET_SCH_SFQ=y CONFIG_NET_SCH_TEQL=y CONFIG_NET_SCH_TBF=y

Hello... Im trying to setup HTB to allow me to shape traffic from two upstreams that meets on single lan0 interface. I prefer to use HTB qdisc within HTB root qdisc for cleaner rules design. Seems that it doesnt work at all. tc -s class show doesnt show any traffic on other classes attached to HTB qdisc. Linux 2.6.20.7 iproute-2.6.20-070313 Weird thing is that tc -s class show that 1: and 2: