similar to: calculating burst for TBF

Hi, I am a completely newbie, and have been doing intense reading for the entire last week, and have the following novice question: In section 9.2.2.2. of LARTC HOWTO, the following sample configuration given: # tc qdisc add dev ppp0 root tbf rate 220kbit latency 50ms burst 1540 Why is the burst parameter value determined to be 1540? Thanks, Todd

I am using tbf to do rate limitation. i set the rate, burst and latency parameters for tbf. but when i start passing data i notice that there is an initial burst and then the rate goes down to the configured level. is this because tbf starts with a full bucket? thanks. __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection

Hi i have found a problem related with tbf and the latency that the tbf calculates.. I have used the following parameters for burst and limit burst 100Kbit limit 500Kbit lat81.8ms burst 6Kbit limit 6Kbit lat 0us burst 200Kbit limit 100Kbit lat 4294.9s As u can see in the 3rd column the latency for 100Kbit burst and 500Kbit limit is 81.8ms but for 200Kbit and limit 100Kbit is 4294.9s!!! How

I''m trying to fill a token bucket with enough tokens to burst several gigs of data. However, it doesn''t seem to get any higher than ~3.9GB: >tc qdisc add dev eth0 root tbf rate 1440kbit latency 50ms \ burst 16000000000 >tc qdisc show dev eth0 qdisc tbf 800b: rate 1440Kbit burst 3908420240b lat 2197.8s A smaller attempt of ~1.6 gigs works just fine: >tc qdisc

Hi Everyone, This is a simple question but I don''t understand why the below tbf is not working as expected by throttling traffic to 5kbps If I throttle a PC''s traffic using the below when traffic exceeds 5kbps packets start getting dropped (as they should) but all traffic gets dropped. not just the bit over 5kbps. TC="tc add dev ppp0" $TC parent 8001:2 handle 2:

Probably this is an old question, but i''m not able to find nothing about... So, i''ve just started to play with tc to limit the transfer speed to my hdsl connection. I''m using the tbf and the command # tc qdisc add dev eth0 root tbf rate 10kbit latency 50ms burst 1000 Then i''ve tried to transfer a big (20 Mbyte) file onto my lan, using ftp and the client

I am using tbf to do bandwidth limitation. i found that when i start passing traffic there is a burst and then the rate goes down to what is configured. is this a known issue or do i need to change some parameters? thanks. --------------------------------- Do you Yahoo!? Read only the mail you want - Yahoo! Mail SpamGuard. _______________________________________________ LARTC mailing list

Hello, I was attempting to throttle egress traffic to a specific rate using a tbf. As a starting point I used an example from the LARTC howto, which goes: tc qdisc add dev eth1 root tbf rate 220kbit latency 50ms burst 1540 I then attempt a large fetch from another machine via wget (~40 megs) and the rate was clamped down to about 12Kbytes/s. As this seemed too much, I gradually increased

The docs[1][2] suggest it''s 1024, but tc says something else: # tc qdisc add dev eth0 root tbf rate 1kbps latency 50ms burst 1500 # tc -s qdisc ls dev eth0 qdisc tbf 8009: rate 8000bit burst 1499b lat 48.8ms ^^^^^^^ Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0) rate 0bit 0pps backlog 0b 0p requeues 0 If 1k were 1024, then I would have 8192bit above.

Hello, i have a server (486sx and 16ram). It gives me this error : NETDEVICE WATCHDOG eth1 : ...timeout. I checked in many places for solutions. Even wrote to this mailinglist. But lately i recived information, that too much upload may mix my adsl modem up. So..... my question is how should my script look while the situation is : eth0 - connected to adsl modem and thus to internet eth1 -

Dear friends, thanks for the last advices about TBF. After reading the tbf.pdf document I got a better insight of the problems I had trying to limit the bandwith on my testbed with a high resolution. The question I have now is: Would I get an immediatly better resolution result if I change the #define HZ to 1000 for my Linux box? I have a Pentium Celeron 700 MHz, and I would like to see the tbf

Hi all! I just started to experiment with bandwidth management using tbf. I have the folowing problems with token understanding: 1) What unit is token? Is "1 token = 1 byte" ? If this is so, then with rate=0.5mbit and HZ=100 the bucket gets filled with 0,64kb (655 tokens) every 10ms? 2) How much tokens are used for one packet (1500)? 3) And token unrelated question. Does

Hello Please give advice in selecting suitable QoS Solution for our device. It contains one WAN port and a LAN port(4 port switch). The WAN will be connected to an ADSL modem(so we don`t know the bandwidth in advance for the WAN and depends on the ADSL connection taken). We need to give highest priority to the Voice and control the WAN bandwidth to 2Mbps. I tried with the TBF by giving 500kbps

Hi have set the following tbf tc qdisc add dev eth0 root tbf rate 0.5mbit \ burst 5kb latency 70ms peakrate 1mbit \ minburst 1540 I want to add a filter so the ip traffic pass from it.. plz help me __________________________________ Yahoo! Mail Stay connected, organized, and protected. Take the tour: http://tour.mail.yahoo.com/mailtour.html

I presently use TBF with this syntax: tc qdisc add dev eth0 parent 1:100 tbf buffer=15000/8 LIMIT=30000 MTU=1500 parent class is a cbq with rate=128Kbit when I want to add PEAK, I get always RTNETLINK error: Invalid argument. Maybe be I don''t understand this parameter. What I know about it, it''s that it can control short-term burst traffic, and it''s what I need to do.

I have htb on 486 sx with 16mb ram. Slackware 9.1. Connection : dsl 1Mbit. 486 works as router and trafic shaper for network made of 12 pc''s. it does the job quite well, but when i play Counter-Strike or connect to my 486 via ssh (on lan), i get huge lag every 11-20 sec. when i connect to 486 via ssh and run iptraf program i see all the trafic, and after a while when lag comes the

Quick question: How do I delete an ingress tbf? [root@atlas root]# tc qdisc qdisc tbf ffff: dev eth0 rate 50Kbit burst 2999b lat 1us [root@atlas root]# tc qdisc del dev eth0 ingress RTNETLINK answers: Invalid argument _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

Hi everybody, it is my first message here. I tried to browse throughout older posts but I found no immediate answer. I need to change rate of a tbf queue while ip packets are already enqueued by it. If I go: tc qdisc replace|change|link dev eth0 root tbf rate 180kbit burst 1540 limit 15400 as results all enqueued packets seems to disappear. I can see that from a: tc -s qdisc ls dev eth0

Hi, I would like to know how to specify the token rate when a tbf qdic is created using tc tool.. Will it be a default value when tbf qdisc is created? This could be a silly question.... im quite new to all these stuff.. but im really interested.. any help will be most appreciated... thanks in advance, sanjeev -- ______________________________________________ Check out the latest SMS

Hello, i have a server (486sx and 16ram). My pc is providing internet to 12 other computers. Ethernet cards are realteks 8139 (drivers builtin to the kernel 2.6.8). It gives me this error : NETDEVICE WATCHDOG eth1 : ...timeout. I checked in many places for solutions. Even wrote to this mailinglist. But lately i recived information, that too much upload may mix my adsl modem up. So..... my