similar to: HFSC and prioritization

When I start my script: * - Creating classes on br1 for upload control ... * - tc class add dev br1 parent 2:0 classid 2:46 hfsc ls m1 576.0Kbit d 2000ms m2 192.0Kbit ul m2 384Kbit ... [ ok ] * - tc class add dev br1 parent 2:46 classid 2:47 hfsc sc umax 1500b dmax 30ms rate 80Kbit . [ ok ] * - tc class add dev br1 parent 2:46 classid 2:48 hfsc ls m2 152.0Kbit ul m2 152.0Kbit

HTB and imq was used to control traffic. modprobe imq numdevs=3 but only imq0 and imq1 can be used; if there are five NICs, please tell me how can I can use imq2 , imq3 and so on. _________________________________________________________ Do You Yahoo!? 新鲜到底,娱乐到家 - 雅虎推出免费娱乐电子周报! http://cn.ent.yahoo.com/newsletter/index.html _______________________________________________ LARTC mailing list /

I have to match my packets based on MAC address, which I cannot do in the POSTROUTING chain, so I do it in PREROUTING using MARK. Then, I match on the MARK in the POSTROUTING chain to do a CLASSIFY. But this does not seem to work: wireless-r1 bwlimit # iptables -L -v -n -t mangle Chain PREROUTING (policy ACCEPT 3353K packets, 941M bytes) pkts bytes target prot opt in out source

Hi! I''m trying to shape my internet connection traffic using hsfc and I''ve encountered the following problem (may not be connected with hfsc). on my lan interface I shape incoming traffic like this: tc qdisc add root dev eth1 handle 1: hfsc default 1003 tc class add dev eth1 parent 1:0 classid 1:1003 hfsc ls rate 10kbit ul rate 10kbit tc class add dev eth1 parent 1: classid

Hi All, I''m trying to create a contended section of bandwidth using IMQ. I have the imq0 device up and running, with traffic passing through it. Firstly, I need to throttle the entire device imq0 to 2mbit/s. I would then like to add throttle rules for individual IP addresses, allowing them to pass up to 512kbit/s each, as long as imq0 has not reached its 2mbit/s. The configuration

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Greetings all, Working in concert with the original authors, Klaus Rechert and Patrick McHardy, I have translated their article "HFSC Scheduling mit Linux" [0] on Hierarchical Fair Service Curve (HFSC) into English [1]. http://linux-ip.net/tc/hfsc.en/ Although the original content is not available directly from their website,

On my debian woody (kernel 2.4.31) the tcpdump doesn''t work with imq0 devices. If I try to tcpdump imq devices there is no packet seen: [...] rt1:~# tcpdump -n -i imq0 Warning: arptype 65535 not supported by libpcap - falling back to cooked socket tcpdump: WARNING: imq0: no IPv4 address assigned tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on

HTB versus HFSC, both qdisc offer the same kind of service, if you want to see comparative test results, go to http://www.rawsoft.org at the line "TEST RESULTS" you will find the results for a sharing test and a burst test. You will see that both qdisc are good. _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl

Hello list, I am now using hfsc for QOS. I have something like this: tc qdisc add dev ethx root handle 1: hfsc default 9 tc class add dev ethx parent 1: classid 1:1 hfsc ls m2 70mbit ul m2 70mbit tc class add dev ethx parent 1:1 classid 1:9 hfsc ls m2 7mbit #DNS stuff follows tc class add dev ethx parent 1:1 classid 1:2 hfsc rt m1 12mbit d 1ms m2 1mbit #Half-life tc class add dev ethx parent

Hi, I''m trying to get a handle on hfsc. Here is my configuration: root@jmnrouter:/jmn# tc class show dev vlan1 class hfsc 1: root class hfsc 1:1 parent 1: ls m1 0bit d 0us m2 225000bit ul m1 0bit d 0us m2 225000bit class hfsc 1:10 parent 1:1 rt m1 191000bit d 25.0ms m2 135000bit ls m1 0bit d 0us m2 135000bit ul m1 0bit d 0us m2 225000bit class hfsc 1:20 parent 1:1 rt m1 22008bit d

Hello, I''m having such problem with HFSC with following config: + tc qdisc del dev eth3 root + tc qdisc add dev eth3 root handle 1: hfsc default 2 + tc class add dev eth3 parent 1: classid 1:1 hfsc ls rate 512kbit ul rate 512kbit + tc class add dev eth3 parent 1:1 classid 1:2 hfsc ls rate 2kbit ul rate 400kbit + tc class add dev eth3 parent 1:1 classid 1:3 hfsc ls rate 32kbit ul rate

Hello All, I am trying to prioratize VOIP traffic from data. The follwing link says that HFSC is better than HTB for shaping VOIP traffic. http://www.voip-info.org/wiki-QoS+Linux+with+HFSC I am in search of good documentation to start with HFSC, I am unable to understand the parameters used. I "googled" a lot to find on how to use HFSC, but no luck. Can anyone of you get me a link To

Hi: I am using a machine with the 2.4.26 kernel, and trying to compare the performance of the HTB qdisc with the HFSC one. I have the following simple script that allows me to have a video stream on port 1234 while it limits a ttcp UDP stream so that the video stream is unimpaired. #!/bin/bash tc qdisc add dev eth0 root handle 1: htb default 12 tc class add dev eth0 parent 1: classid 1:1

I have a lot question about tc-command because now i''m doing research to compare performance between HTB and  HFSC so i''m doubt a lot thing and your reply are so very helpful to me ... My question is In HTB tc command question 1. I''m use opensource (Mastershaper) for help to config traffic control but when i''m try to config HTB, I''m doubt about

ingress can be used to control the incoming packet, such as: tc qdisc add dev eth0 handle ffff: ingress tc filter add dev eth0 parent ffff: protocol ip prio 5 u32 match ip src 172.16.1.11 police rate 10kbit burst 10k drop flowid :1 tc filter add dev eth0 parent ffff: protocol ip prio 5 u32 match ip src 172.16.1.22 police rate 10kbit burst 10k drop flowid :2 first ,I do not sure these method can

Hello, I have finally managed to understand HFSC up to a level which allowed me to create a QoS script which maintains low VoIP latency while running stuff like eMule. Unfortunately, HFSC seems to have a severe bug. Why do I consider this as a bug defenitely? Well, my script runs without any errors, then QoS works perfectly for some hours, no error messages in kernel log. Then randomly the

I don''t understand the following: root@jmnrouter:~# tc -s class ls dev vlan1 && tc -s qdisc ls dev vlan1 class hfsc 1: root Sent 0 bytes 0 pkts (dropped 0, overlimits 0) period 0 level 2 class hfsc 1:1 parent 1: sc m1 0bit d 0us m2 220000bit ul m1 0bit d 0us m2 220000bit Sent 0 bytes 0 pkts (dropped 0, overlimits 0) period 31304 work 7533852 bytes level 1 class hfsc 1:10

Hi! Do you know somthing about hfsc and bps? There''s no output for speed only for packets. Doesn''t hfsc support such a field? tc -s class show dev eth0 class hfsc 1: root Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0) rate 0bit 0pps backlog 0b 0p requeues 0 period 0 level 2 class hfsc 1:11 parent 1:1 sc m1 0bit d 18.0ms m2 1000Kbit ul m1 0bit d 0us m2

after i use "tc -s -d class ls dev eth0" will show statistic data about HFSC ,like this root@ubuntu:/home/shaper# tc -s -d class ls dev eth2 class hfsc 1: root Sent 0 bytes 0 pkts (dropped 0, overlimits 0) period 24 work 13844792199226589188 bytes rtwork 20937281664 bytes level 3461036864 class hfsc 1:11 parent 1:1 sc m1 30720Kbit d 10.0ms m2 30000bit ul m1 0bit d 0us m2

My hfsc rule .. tc qdisc add dev eth2 handle 1: root hfsc iptables -t mangle -N ms-all iptables -t mangle -N ms-all-chains iptables -t mangle -N ms-prerouting iptables -t mangle -A PREROUTING -j ms-prerouting iptables -t mangle -A ms-prerouting -j CONNMARK --restore-mark iptables -t mangle -A ms-prerouting -p udp --dport 4444 -j MARK --set-mark 1 iptables -t mangle -A ms-prerouting -p udp -m