similar to: limit users to use resource

Hi List; How to upgrade the Asterisk, Zaptel and LibPri and keep the configuration the same? I do not need to remove current asterisk, zaptel and libpri and download new one and write new configuration. Regards, -------------- ITS IP Telephony and Contact Center Engineer Eng. Bilal Ghayad Mobile: 00965 9849460

My asterisk should follow 302 redirect which it receives from other sip server(10.10.10.10). By running network sniffer I see, that asterisk receives 302 answer, but doesn't follow it. My config is: sip.conf: ....... [out4] type=peer host=10.10.10.10 canreinvite=no promiscredir=yes insecure=very disallow=all allow=g729 allow=g723 ....... extensions.conf: [to-sip] exten => _0011X., 1,

Hi List; Any one can advise me to a good link to see and buy Polycom IP Phones? Also, if I need support (in case the Phone was damaged and need to replace, so the warantee), so which web can provide that? I do not need to buy from one and he is not responsible for support. Regards Bilal ____________________________________________________________________________________ Be a better

Hi List; I need to use an prepaid billing system with Asterisk, and I do not know which one is more stable and integrated with Asterisk? A2Billing or AstBill or ASTCC? Also, from where I can download it and ready about its configuration? Regards ITS IP Telephony and Contact Center Engineer Eng. Bilal Ghayad Mobile: 009659849460

Hi all I change the monitor to LG LCD but x window couldn't start because of the "out of range" signal in the monitor How can I fix this problem Thank you

Hi List; Where I determine the codec to be used for the SIP Trunk (between Asterik and another SIP softswitch)? Regards Bilal ____________________________________________________________________________________ Be a better Heartthrob. Get better relationship answers from someone who knows. Yahoo! Answers - Check it out. http://answers.yahoo.com/dir/?link=list&sid=396545433

Hi! I have a situation where we want to set up two different rails applications on the same server and they both have ferret related functionality that needs to be implemented. How does one setup the ferret_server.yml file and then start each ferrt server to reflect that these two applications should access specific ferret servers that are running? I''ve tried changing the ports in

Hi, As I recall, 3.0.25a creates it's OWN krb5.conf file based on info it gets back from the DC to try to handle site stuff (so it uses the 'nearest' kdc, etc). I forget exactly how this mech. works, but if the kdc returned with the site info (which subsequently gets built into samba's personal 'krb5.conf' file) is down, or replication is off, your kinit would work,

I am trying to retrieve the "dialed peer number" but it seems that ${DIALEDPEERNUMBER} is "broken". Also, I know that I could extract the dialed number from the ${CHANNEL} variable but this only works for SIP and maybe IAX (untested). However, it doesn't work for ZAP. All I get when using ZAP is something like "Zap/1-1" (for SIP I would get

> I'm using Asterisk 1.4 and I'm wanting to set an > account code for incoming calls. In the > extensions.conf file I have the following: > > exten => s,1,SetAccount(1234) > exten => s,n,Dial(SIP/1234) > > Then when I dial the extension the following error > message pops up in the CLI: > > [Jun 6 19:12:40] WARNING[28167]: pbx.c:1783 >

Dear List; How can I place a call via Zap/g1 (group) but need to determine the line (FXO port) that will go via it? Also, how it will be possible to assign an dedicated line (connected to FXO) to an button on the Polycom IP Phone or Broadtel IP Phone, so if user select that button then he will be sure that his outside call will be via that specific line. Regards Bilal

Hi List; If I need to do a trunk between Asterisk and another SIP softswitch (so Asterisk will send a SIP calls to that softswitch), then I have to configure this on the sip.conf file or where exactly? And is it the same when I configure iax trunk? Should I determine the context in this case for this SIP trunk? Regards Bilal

Hi, I setup a queue (number 4050) with one static agent (extension 4054). What I would like is that when someone calls the 4050 queue and there are neither "dynamic" agents logged in nor is the static agent 4054 "on-line" then the caller gets out of the queue and falls into another context (eg. voicemail or anything). Not "on-line" means that either the SIP

HI Can I install Centos on Segate ST3160812AS ( SATA II ) Harddisk? Asky

I'm trying to kickstart a Centos 4.1 system with the minimum set of packages. I have no use for ypbind so I'm trying to prevent from being installed, but kickstart/anaconda always insist on its installation (complaining that the package is missing). This is the %packages section of my ks file so far: %packages #-@ dialup kernel grub e2fsprogs lvm2 -slocate -bluez-utils -bluez-bluefw

Hi, To get my system on time, I usually issue these two commands: # ntpdate de.pool.ntp.org # hwclock -w And when I want this to be done on startup, I put the two lines in rc.local. I wonder if this is an orthodox way to do things. Or is there something more appropriate? Niki Kovacs

I have been asked to update OpenLDAP to the latest stable version. I am using CentOS 4.2 and have OpenLDAP 2.2.13 installed. I can install from source if I have to, but I would rather stay with rpm packages if possible. I found an rpm from Fedora Core Development on RPMFIND. Will this one work with Centos, or should I grab the source rpm and rebuild it? Bowie

Helo, I've just installed a CentOS 4.0, postgress,iptables, ect.. on a P 4 Intel using sotf RAID 1 ...and everything is fine. I bought a HP DLT 40/80G tape device for being use as tape backup to my server. My questions are: 1. What you recomended me to use as a soft backUP. (amanda, dump/restore, TAR scipts, other)? 2. How can I backUP my entire filesystem ..(I mean everything using one the

I have the latest kernel with the drivers for my 3ware 9550SX built in. Where can I find the tools and monitoring apps for this card? Are there rpms hiding somewhere, or do I need to build it from source? -- Bowie

hi to all, im using my box for mail server (CENTOS 4.4 ) is there any RPM packages for courier authlib,courier-map,maildrop for CENTOS 4.4 ,any link how to get it, any suggestion, thanks to all in advanced,any suggestion will appreciate. TIA, dennis -------------- next part -------------- An HTML attachment was scrubbed... URL: