similar to: two isp issues

I have three ethernet card and two of them connected to diffrent ISP and has diffrent gateways. And one ethernet card is connected to local lan. I have installed iptables and configured the firwall to work as nat gateway for the users. Now I want to route only mail traffic to the perticular ISP and which I am not able to do it. I have done iproute configuration what ever lartc said. But still I

Anyone has configued Multivoip 3010 with Asterisk ? I am tring to configure this box to work with asterisk . Thanks Imthiyaz -------------------------------------------------------------------- mail2web - Check your email from the web at http://mail2web.com/ .

Dear folks, Here goes my bandwidth manager: INTERNET | |eth0 202.14.41.1 BW.Manager | | | +----eth1----192.168.1.0/24 | +------eth2----192.168.2.0/24 Total incoming bandwidth to eth0 is 1024kbps should be shared to eth1 and eth2, which mean each get 512Kbps and burstable to 1024Kbps if other host is idle. My question is how do i apply HTB to these situation ? As far as i know eth1 and eth2

Hello! I have a problem. May be here exist anyone who has encountered with the following problem. I have a router which is connected to 2 ISP from external side and one LAN internal interface. The feature is that the one ISP allocates a subnet xxx.xxx.xxx.160/28 for me but I split it into two subnets xxx.xxx.xxx.160/29 and xxx.xxx.xxx.168/29 and assign the latter to the internal interface. Also

hi, Im tryig to use two isp links get worked: first isp 212.122.xx.254 (gw) second isp 10.10.xx.2 (gw) my ip1 212.122.xx.90 (eth0) my ip2 10.10.xx.254 (eth1) internal network my ip 192.168.1.254 (eth2) turn on masquerading on both links: $IPTABLES -t nat -A POSTROUTING -o eth0 -j SNAT --to 212.122.xx.90 $IPTABLES -t nat -A POSTROUTING -o eth1 -j SNAT --to 10.10.xx.2 mark packets on 6667

Hello, I have 2 ISP uplinks (zones: inet1 and inet2), each with a fixed IP on the outside and a routed subnet (/25 and /26) on the inside. So, behind the firewall i have 2 networksegments (lan1 and lan2) with public IP-addresses. The segments are completely isolated from eachother: hosts in zone "lan1" connect only to "inet1" and hosts in zone "lan2" only connect

I have a working router (thanks to Julian''s patches and the threads on this site) load balancing over Dual ISP''s. Links for the curious (see router setup below as well) - Necessary Patches - http://www.ssi.bg/~ja/ How to Patch (I use Debian Sarge and downloaded the latest source from kernel.org) - http://www.desktop-linux.net/debkernel.htm Necessary Reading -

Hi, I have a linux-box with 3 eth, 2 of us go into 2 ISP. My localnet is masquerade with this rule: Chain PREROUTING (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination SNAT all -- 10.0.0.0/16 anywhere to:211.56.233.186 SNAT all --

Hello,I have single linux router ( fedora core 1 ), 2 ISP, 1 internal network,1 IP space from every ISP My scenario: eth0 1.0.0.2 netmask 255.255.255.252 -> ISP 1 eth1 2.0.0.2 netmask 255.255.255.252 -> ISP 2 eth2 1.0.1.1 netmask 255.255.255.0 -> IP space from ISP1 eth3 2.0.1.1 netmask 255.255.255.0 -> IP space from ISP2 Config I try: /etc/iproute2/rt_tables: 10 isp1 20 isp2 ip

I''m trying to connect to two ISPs the connections are as follows: Eth0 IP: 192.168.1.1 Mask: 255.255.255.0 Eth1 IP: 216.167.217.241 Mask: 255.255.255.0 Eth2 IP: 216.167.208.40 Mask: 255.255.255.0 Here are the commands to set things up: #Load modules insmod /lib/modules/2.6.19.2- pyramid.metrix.net/kernel/net/ipv4/multipath_drr.ko insmod /lib/modules/2.6.19.2-

I have a setup with two Internet providers. One circuit (net0 == eth1) is used primarily for employees and tunnels to other sites. The other (net1 == eth2) is for the production machines that customers access. Everythung works in teh sense that packets get to where they are sent (mostly) but I recently I had a sniffer on the system and noticed a problem I cannot solve. traffic coming in

Hi, I'm about to test VOIP connection (from my ISP provider) directly through dedicated network card instead of going through ADSL gateway with analog phone port - SPA 3000 - Asterisk. I need to have eth2 set on dhcp (to retrieve IP automatically) and then work with it under Asterisk as dedicated VOIP trunk. Anyone with more insight how to setup such situation ? Any more info anywhere

Hello all. First of all, please be a bit indulgent to my poor English :-). Second, this message is "kinda" BIG, so if you don''t like BIG messages, simply don''t read it :-). I''ve read http://shorewall.net/2.0/Shorewall_and_Routing.html and http://shorewall.net/MultiISP.html, however I still a bit confused how to organize what I need :-). I''ve a

Hello Shorewall list, I''m a happy Shorewall user since a few years now and everything works fine for me except one thing that I try to implement since a week, the multi-isp. I''ve downloaded the 2.4.0 Stable release yesterday and tried the RC2 since a week. My config is a Debian running a kernel 2.4.27 home made with the CONNMARK.diff patch applied I''m using 2 ISP,

I configured multiple isp (actually only multiple gw) according http://lartc.org/howto/lartc.rpdb.multiple-links.html. Now NAT (Internet) seems to work, both external interfaces work ( I didnt configure load balancing because I dont need it). However I have problem that I can not ping from NAT to public ip of my Linux box. Problem is that I can not connect from 192.168.1.0/24 network to services

I''ll take it from the begining... About one year ago I only had 1 IP and used wondershaper. It worked great. Now I got /27 (32 IPs) and a gw computer that talks to two ISPs via a two tunnels. See: http://www.flashdance.cx/pics/flashdance-LAN.png I _really_ have a need to do QoS on my connection, for example I host websites that uses all available upstream. When I download at the same

Hi, I am want to setup linux box as router with fallback routing. ISP 1 (Cable Modem, Static public IP) ISP 2 (ADLS Router Dynamic IP SUA NAT on router) ISP 1 ISP2 | | | Dyn IP (SUA NAT) | DLS router Cable Modem | (Static IP) | (192.168.1.1 | | | | eth1

Below is a snippet from my firewall script isp1_ip="xx.0.5.20" isp1_gw="xx.0.5.1" isp1_net="xx.0.5.0/28" isp1_if="eth2" isp2_ip="xx.182.19.88" isp2_gw="xx.182.19.1" isp2_net="xx.182.19.0/28" isp2_if="eth3" lo_ip="127.0.0.1" lo_if="lo" lo_net="127.0.0.1/8"

Below is a snippet from my firewall script isp1_ip="xx.0.5.20" isp1_gw="xx.0.5.1" isp1_net="xx.0.5.0/28" isp1_if="eth2" isp2_ip="xx.182.19.88" isp2_gw="xx.182.19.1" isp2_net="xx.182.19.0/28" isp2_if="eth3" lo_ip="127.0.0.1" lo_if="lo" lo_net="127.0.0.1/8" ip rule delete

Dear all Lartc, I try to split my Internet access to my 2 ISP with 1 linux (GNU/Debian sarge) 3 NIC router, I want all my users conneted with ISP1 and just some IP connected with ISP2 Here is my configuration: Internal network: 10.117.71.0/24 Interface eth0 ISP1: IP for my linux box: 1.2.3.4/29 Interface: eth1 Gateway: 1.2.3.5 ISP2: IP for my