similar to: Rate limits whithin rate limits

Hi all, I''m having some problems setting up qdiscs on a bridge.The config looks a little like this: ifconfig ifb0 up # Bring up the IFB for this bridge. tc qdisc add dev eth2 ingress tc qdisc add dev eth3 ingress tc qdisc add dev ifb0 root handle 1:0 cbq bandwidth 100Mbit avpkt 1000 cell 8 # Raw qdiscs on each bridge port tc qdisc add dev eth2 root handle 1:0 cbq bandwidth

Hi all, I''m having a hell of a time getting my IFB to work. I know I''ve done this before, so I''m missing something stupid. Can anybody tell me what it might be? Configs as follows: -------- #!/bin/sh modprobe ifb numifbs=1000 modprobe act_mirred modprobe 8021q brctl addbr br0 brctl setfd br0 0 brctl stp br0 off brctl addif br0 eth1 brctl addif br0 eth2 ifconfig eth1

Hi, I'm having trouble getting networking to work and I'm not sure what I'm doing wrong. The network interface of the host is connected to a switch-port that is configured as trunk and allows tagged traffic for vlan id 10. The host itself has the interfaces eth1.10 and eth1 defined. eth1.10 is configured with the primary ip address of the host system and eth1 is slave of the bridge

Hello all, I am having some trouble getting a firewall filter to work with TC. I am actually setting the mark via EBTables (which is working as far as I can tell, I am also logging the packet and my syslog reports lots of marks): ebtables -t broute -A BROUTING -p ipv4 -i eth1 -s 08:00:46:60:B3:57 -j mark --set-mark 7 --mark-target CONTINUE --log --log-level debug --log-prefix "EBFW Mark

Hello What I''m looking for is how to configure the Linux QoS module to do global rate limitation for two (or more) 802.1q pseudo network devices. I naturally suppose there is a possibility with IFB. I don''t want to use IMQ because it''s not integrated to my kernel v2.6.21.1 and I didn''t find IMQ patches for it nor for the iptables package I use (v1.3.7).

hey guys i am regulating the traffic to & fro by my network through a linux gateway , its behaving strange. i regulated Downlink to 2Mbps & UPlLINK to 500Kbps. both perform well when those are done independent i.e. one at a time but when i do both from a client system ..the downlink however continues at 2mbps but the uplink falls down to 100kbps? is something wrong with my script or

Hi,All I am using iproute2 to manage bandwith for ADSL router.High,medium,low priority are needed for different protocol port on the ADSL's upstream side,as following: LAN --- |ADSL Router|------WAN When there aren't traffic on the specific priority, its bandwidth should be borrowed by other priorities.But it doesn't work.Here is my script: /usr/sbin/tc qdisc del dev nas0 root

Hi all I am conducting the experiments comparing IP router forwarding delay and MPLS LSR forwarding delay, it is obvious in theory MPLS in Core should be faster than IP, but for small netork (only have several core routers), result show it is not, this is why I want emulate a large IP routing table in one core router. can I do it and how ? right now I use static routing table (by using command :

I need to shape traffic from some IP on one LAN, but I''m in trouble. There is a linux 2.4.26 connected to the Internet (eth0) / LAN(eth1) doing NAT. I''m using VLANs in the LAN Interface, that is connected to a 3Com SuperStack II in a 802.1Q tagged port. I want to create a class that will limit the traffic at 384Kbit/s. I want to create two leaf classes that limit the traffic at

Hello! I have a problem here. I set up a Linux 2.4 machine to do bandwidth limiting for some of our customers. Current setup is something like this: |--------| backbone |-------| |---------| |Internet|225.1-----------225.10|limiter|228.1----228.10|cust. gw2| |--------| | eth0 |-------| eth1 |---------| | 225.20

Hello all, I''ve got a couple redundant (Spanning Tree Protocol) boxes running FC1 minimal install + bridge-utils and they are working great for QoS + ntop monitoring. I''m wondering if I should handle the VoIP traffic a little differently. I don''t mind letting VoIP and Video lend out traffic when it isn''t being used, so that''s why I gave them such

Hi All, I found 2 unusual behavior with u32 classifier in Kernel 2.4.12. I’ve u32 compiled as module. 1> u32 filter seems not working if there is already some fw filter used for some other class. In order to get u32 working I’ve to delete root class, which in terms delete all fw filters too, and then same command for u32 works. fw is also compiled as module. 2> If I add u32 filter to my

Hi all, I have installed 2.4.5 kernel, Debian Potato. my tc script: #!/bin/bash tc qdisc add dev eth1 root handle 20: cbq bandwidth 10Mbit avpkt 1000 echo root tc class add dev eth1 parent 20:0 classid 20:1 cbq bandwidth 10Mbit rate \ 10Mbit allot 1514 weight 1Mbit prio 8 maxburst 20 avpkt 1000 echo class tc class add dev eth1 parent 20:1 classid 20:100 cbq bandwidth 10Mbit rate \ 5Mbit allot

Hi! I just recently entered the wonderful world of the so called "advanced routing" and decided to try and limit the bandwidth of a MASQed network here and ended up in trouble :(. The setup is (as far as I can tell) pretty straightforward. eth0 is connected to the "real" network with a proper IP, and eth2 is 192.168.10.x (the MASQed network). All of it is basicly right out of

all: I"m just trying to create a simple rsvp session to familiarize myself with the protocol. I don''t ever get a rsvp RESV message only PATH AND PATH TEAR messages. There is a timeout but i''m not sure whats causing it exactly. Can anyone shed some light on why? All the configs and output are below. Please let me know if you need more information. Thanks. Jon Test

I am using a server with asterisk and I am trying to prioritize voip traffick -- I am a newbie at this traffic shaping, so please bear with me. I used the script below and what happens is thatall traffic in the bulk class stops after a couple of minutes. Also, should I include the ports for rtp in the filter statements with the ports 5061 and 4569? Note I have a fairly big pipe -- supposed to

Have a few generic questions about Kom-RSVP 1.) 11:00:05.175 WARNING: timer system overloaded, deviation is 30.080 sec - what timer is this referring to? System time? 2.) What is the relationship between the CBQ class created for RSVP traffic and the CBQ parameter that is in RSVP.conf? - ex. ### cbq qdisc ### tc qdisc add dev eth0 root handle 1: cbq bandwidth 10mbit avpkt 1000 mpu 64

Hi. I want to shape traffic from some IPs in my lan, but I''m w/ trouble. I have a linux box connected to the Internet. In the other side of this box is my LAN. I want to create the following scenario: My root qdisc is attached to a 100Mbit/s NIC I want to create a class attached to this qdisc that will limit the traffic at 384Kbit/s. I want to create two leaf classes that limits

Hello all, I am testing CBQ and HTB these days and I got a lots problem which needs your help. It is a little long text :) Thank you! (All my test is based on Redhat Linux9.0) 1.Is isolated of CBQ working? I have read Mr. stef word that he never made cbq isolated work. 2. I have setup an environment to test cbq: one tcp flow which I should protect and a noisy udp flow who will eat much of the

Hello, I''m using tc to limit the bandwidth of our wireless customers. I have a working script, but I''m not happy with it. I''m trying to write a more sophisticated script, but when I run it, it give me this error: RTNETLINK answers: File exists I have no idea what this error means or how to fix it. Here is a portion of the script (the whole script shapes several