similar to: How to become your IP range...

Hi All, How do I find out about new new DHCP connections as they appear? I want to write a script that will do some stuff based on a new ip request from a machine on my lan. ie - new user connects to the lan, DHCP server on my Linux (debian) gateway gives them an IP, my script is run automatically to change the firewall rules and start recording their presents, or if it''s an unknown

ClarkConnect Home 3.2 eth0 - WAN - inet - ip:192.168.1.2 gw:192.168.1.1 (connected to my www.woosh.co.nz gatway) wlan - WAN - private community wireless networt - ip:10.252.16.16 gw:10.252.16.1 eth1 - LAN - ip:192.168.2.1 # route add -net 10.0.0.0 netmask 255.0.0.0 gw 10.252.16.1 [root@bowenvale etc]# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface

Hi All, I''m trying to find the right tools to be able to track the amount of data that my users and pulling accross our VPN links. I''ve already done a google and hunted thru the Redhat web site but I''m really just not sure what I''m looking for. Could someone give me some links or even the correct terms would be a start. Cheers DiG Ask not what your

Hello, list members, can i limit pps rate with linux? How? -m limit does not fit, as i understood: it can help with low rates only (is that true? any suggestions?) Thank you, -- _,-=._ /|_/| `-.} `=._,.-=-._., @ @._, `._ _,-. ) _,.-'' ` G.m-"^m`m'' Dmytro O. Redchuk

Hi all, Situation: We use smbtar for backups, incrementals done using -N <last date file>, and this has worked well with samba 2.2.x After upgrading to 3.0b3, using the -N (newer) option to smbtar causes a bad interaction with smbclient. Eg,: # smbtar -s PC -x Share -u User -p Pwd -d / -t - -N last-backup -v gives (if you print out the eval at the end of smbtar script): eval

I am doing some testing of openwrt'd wireless access points, using madwifi-ng'd atheros radios. In the test configuration, I have three devices in a triangle, each has wds links to the other two devices. The ath0 interface is in ap mode, ath1 is a wds link to one device, and ath2 is a wds link to the other device. All three interfaces (and an ethernet interface) are in a bridge (br-lan)

We seem to send 3 extra bytes in a TCN, which will be whatever happens to be on the stack. Thanks to Aji_Srinivas@emc.com for seeing. Signed-off-by: Stephen Hemminger <shemminger@osdl.org> diff -Naur a/net/bridge/br_stp_bpdu.c b/net/bridge/br_stp_bpdu.c --- a/net/bridge/br_stp_bpdu.c 2006-09-03 23:40:08.000000000 +0530 +++ b/net/bridge/br_stp_bpdu.c 2006-09-03 23:40:33.000000000 +0530 @@

Hi. I'm not subscribed, so please Cc: me. This trivial patch fixes a typo that irritates me every time I boot.. --- linux-2.5.orig/net/bridge/br_stp.c 2004-07-19 14:43:44.000000000 +0300 +++ linux-2.5/net/bridge/br_stp.c 2004-07-19 14:53:15.000000000 +0300 @@ -299,7 +299,7 @@ int isroot = br_is_root_bridge(br); pr_info("%s: topology change detected, %s\n",

Hi all, I''m developing Q-in-Q VLAN feature for a router software. Does any open source tools have capacity of capturing and displaying Q-in-Q VLAN packet? Thanks & Regards, Hung ____________________________________________________ Start your day with Yahoo! - make it your home page http://www.yahoo.com/r/hs

Can't access www.xiph.org from Japan. Probably it can't access from the other non-English countries. Please fix it. $ telnet www.xiph.org 80 Trying 195.169.149.105... Connected to www.xiph.org. Escape character is '^]'. GET / HTTP/1.0 Accept: */* Accept-Language: ja Host: www.xiph.org HTTP/1.1 406 Not Acceptable Date: Sun, 25 Sep 2005 18:00:47 GMT Server: Apache/2.0.53 (Ubuntu)

Thanks, Mike. When running tcpdump on the VM I'm not seeing traffic unless it's explicitly intended for that particular VM, so no traffic between the other VMs is getting forwarded from the virtual interface to the "network appliance" VM. There is connectivity between the VMs on the private network and the "network appliance" VM which is acting as a gateway.

dear all: I try to configure a bridge in my embedded linux. I had fininshed these operations below: 1) configure kernel, select the option "802.1d bridge" 2) compile bridge-utils 3) issue these commands: ifconfig eth0 0.0.0.0 ifconfig eth1 0.0.0.0 brctl addbr vb brctl addif vb eth0 brctl addif vb eth1 ifconfig vb 192.168.110.24 up

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I have a machine running 2.6.18-rc3 with a bridge config that looks like this: cr1:~# brctl show bridge name bridge id STP enabled interfaces vlan100 36b0.0007e90f40c1 yes eth0.100 eth2.100 vlan101 5dc0.0007e90f40c1 yes

Hi, we're running the standard linux bridge setup (redundant bridge) for 5 years now. So first of all, thanks to everyone involved for implementing the bridging feature in Linux. Now I'm trying to bridge hosts connected to VLAN'ed Cisco switches using linux bridge. I'm testing the following setup (Kernel 2.6.19, bridge-utils 1.2 on both bridges)

Hi, the networking just drives me crazy and it seems that i am missing something. So here is my situation: i have a server with 2 public IPs (85.214.1.230 and 81.169.1.81) the dom0 is on: ip 81.169.1.81 netmask 255.255.255.255 gw 81.169.1.1 i would like to have a domU with ip 85.214.1.230. I tried everything routing, bridging.. nothing seems to work. my dom0 config; . (network-script

Hi there, I had remote filesystem not unmounting during shutdown so I hit the reboot button. Did so a couple of times in the past. 3.6.8-1-ARCH, btrfs-progs 0.19.20121005-4, don''t remember the exact version I used when creating the filesystem (0.19 something). btrfsck looks like this: checking extents checking fs roots parent transid verify failed on 167047168 wanted 713090 found

dear all: I try to configure a bridge in my embedded linux. I had fininshed these operations below: 1) configure kernel, select the option "802.1d bridge" 2) compile bridge-utils 3) issue these commands: ifconfig eth0 0.0.0.0 ifconfig eth1 0.0.0.0 brctl addbr vb brctl addif vb eth0 brctl addif vb eth1 ifconfig vb 192.168.110.24 up

Hi, the networking just drives me crazy and it seems that i am missing something. So here is my situation: i have a server with 2 public IPs (85.214.1.230 and 81.169.1.81) the dom0 is on: ip 81.169.1.81 netmask 255.255.255.255 gw 81.169.1.1 i would like to have a domU with ip 85.214.1.230. I tried everything routing, bridging.. nothing seems to work. my dom0 config; . (network-script

My lenny guests don''t ping gateway. this is where I have found some probe HPCNL-SR-3:/etc/init.d# brctl showstp eth0 eth0  bridge id              8000.001b210d6131  designated root        8000.001b210d6131  root port                 0                    path cost                  0  max age                  20.00                 bridge max age            20.00  hello time               

I'm trying to get a backup system going. I've got a script that will grab all the files I need, but there are several gigs. The command line i'm using now is: smbclient file://server/share XXXXX -Uuser -Tc /usr/tmp/share.tar /var/log* /usr/home* etc... This is taking too long for all of the servers. What is the exact syntax so I can backup changed/updated files in relation to the