similar to: routing speciffic traffic over speciffic ISP

Hi, i want to do load balancing of 2 ISP's Everything is set up OK but one of the ISP's is loaded on 100% while the other is utilised on 1 - 5% I've read about Julians patches but they stop at 2.6.14. Is anybody aware of similar patches for higher patchlevels. 2.6.14 is not suitable for my setup Thanks for reading :) -- С уважение, Владимир Витков http://www.netsecad.com

Hi all :) there is somekind of strange Routing problem that im getting with Linux-2.6.16 and iproute 2.6.16 , when i use command like : ip route add default nexthop via 1.1.1.1 dev eth0 nexthop via 1.1.1.2 dev eth1 all packets goes on 1.1.1.2 ( always last interface ) , whats is the problem ? this situation also tested with equalize flag , on two physical interface and etc ... -- Lady Luck

Hi, there is a way to graph host''s traffic from my lan ? I''ve a linux router (2.4.x kernel), and a lan: linux router : 192.168.1.254 host 1: 192.168.1.1 host 2: 192.168.1.2 host 3: 192.168.1.3 I''m looking for a way to graph traffic ( in / out ) from each 3 hosts, and store total traffic on a mysql table, in order to make statistics later. I think I can do with Mrtg,

I am trying to build a trafic control rule set for a huge NATed network, and I have it working for single known addresses but I need to scale it to 16M potential client addresses. I''m using iptables for NAT. Incoming traffic is simple because I can match destination address, outgoing traffic I use iptables IPMARK then tc match mark and it works perfectly if I build rules for each client

On Jan 16, 2014, at 4:51 PM, Ariel Wainer wrote: > One small comment: > When the driver has no permission to access the device, it exits with a > segmentation fault, it would be nice to have a more informative error. > I'm not really sure if the issue is speciffic to this driver or is it > general. Good point. I forgot that the permissions errors would happen after the

One small comment: When the driver has no permission to access the device, it exits with a segmentation fault, it would be nice to have a more informative error. I'm not really sure if the issue is speciffic to this driver or is it general. I attached the output of an strace with the driver crashing. Best regards. -------------- next part --------------

Hi, I am working on voice application. I want to identify RTP packets and set DSCP for those. Is there anyway to accomplish this task either using tc or iptables. Please help me.. Thank you -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean.

Let''s say I''m building a "to-do" list application using Ruby on Rails. I decide to sell it to a customer, and distribute the source code files to him. Can I then restrict the user from distrubting the files by creating a license that prohibits distribution? That is, is it possible to create a "single-user" license? Or, am I limited to distributing the

On Jan 12, 2014, at 11:07 AM, Ariel Wainer wrote: > On 11/01/14 15:27, Charles Lepple wrote: >> On Jan 10, 2014, at 4:46 PM, Ariel Wainer wrote: >> >>> On 10/01/14 01:53, Charles Lepple wrote: >>>> I am curious about why the Interrupt Out packet is sent by the Windows software if it isn't to turn off the UPS. Is it possible to do some more testing with

I would lilke to shape upload ftp bandwidth in a dual ISP setup [shorewall show connections] tcp 6 431215 ESTABLISHED src=192.168.2.89 dst=83.xxx.xxx.23 sport=1487 dport=21 src=83.xxx.xxx.23 dst=10.0.11.2 sport=21 dport=1487 [ASSURED] use=2 mark=1 [tcdevices] #INTERFACE IN-BANDWITH OUT-BANDWIDTH $EIF 970kbit 245kbit $LIF 970kbit 245kbit

Hello, syzkaller hit the following crash on f3b5ad89de16f5d42e8ad36fbdf85f705c1ae051 git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/master compiler: gcc (GCC) 7.1.1 20170620 .config is attached Raw console output is attached. C reproducer is attached syzkaller reproducer is attached. See https://goo.gl/kgGztJ for information about syzkaller reproducers

Hi There, We currently using iproute2 for load balancing. However we need more upload speed as we load balance over 3 dsl lines. I''ve been looking for a way to combine the upload speed to more faster. Found a site called www.upstreaminter.net where these guys bond the adsl channels to improve uploads, Since downloading is problem as its need to know the ip address of the downloader they