similar to: --set-mark policy routing problem

Hi, I have a linux box with two dsl modems on it (connection is done via pppoe), I''m trying to route default traffic on the primary connection (ppp0) and mail traffic on another one (ppp1). This traffic will come from the localhost. I run Slackware 9.1 (Kernel 2.4.22), recompiled with necessary options for using iproute2. According to the advanced routing howto, I did the following

Hi all, I have 2 ISPs on a Linux router and a local network with one Linux server and many windows. The local network is masqueraded. I want to give access to port 25 and 80 of my server from any incoming request (i.e. from my 2 ISP). I have made a DNAT translation, witch work but the outgoing answers are not routed correctly. Of course, the de-SNAT process is done before the routing process. So

Hello, I''m running a home-made Debian 2.4.18 kernel with iproute2-ss010824. I have 2 cable-modems to 2 different providers. One with a transparant proxy and one with a regular. I would like to load-balance all traffic over the 2 modems and to do this with http traffic I have to run 2 squid processes: squid1 to act as a proxy for the provider with the transparant proxy and squid2 that

Hello, I have a LINUX server with two internet connections available. I want all the traffic to go over the default route, but HTTP traffic to go over ISP2 line. Interfaces: eth1 192.168.2.254 - LAN 192.168.2.x ppp0 x.x.x.106 - remote gateway x.x.x.6 - ISP1 (default route) eth0 192.168.164.254 - remote gateway 192.168.164.113 - ISP2 (a hardware router) I have the following configuration: echo

Hi, I have been searching around and trying for a few days but still can''t get it works. Hopefully the highhand here can give me hints!! I have 3 adsl connections, 1 is using hardware broadband router to connect and the other 2 are using my debian linux pc to connect. I hope to setup a route policy so that all users except user1 and user2 will use the broadband router connect (eth0),

Hi , this probably was asked many times before , but here it goes.. Until now i was using dsl_qos_queue - http://www.sonicspike.net/software/ Which limits outbound traffic and does packet priorites with iptables using MARKed packets.. works very well , I run a ftpserver + webserver so it''s usefull to set these 2 with lowest priority and my multiplayer gaming running on certain UDP ports

Hello guys, I am still in doubt about this kind of server. So my question is about the "prio" at routing tables like: I have 3 tables in /etc/iproute2/rt_tables: 201 201 202 202 222 222 In table 201 there is the rules about my internet link (frame relay) that comes into eth0. So I made this route into it: [root@ns2 iproute2]# ip route show table 201 default via

Here''s my situation: I''ve got an Intel machine running a 2.6.9 linux kernel and this box has 4 modems attached to it via a usb to serial port expander. In order to force data down each of the modems, some pretty simple rules are used and they are as follows: iptables -t mangle -A OUTPUT -p tcp --dport $PORT1 -j MARK --set-mark 1 iptables -t mangle -A OUTPUT -p tcp --dport

Hi Here is a short description of my network: ppp0 (adsl) ppp1 (adsl) | | | | --------------------- | Router | | Firewall | | MASQUERAD | | DNAT | | | | eth0 | --------------------- | | | ---------------------- |

Hi, I have established two connections to the same ISP. After that ip route list showed this: 195.14.247.94 dev ppp0 proto kernel scope link src 81.173.141.207 195.14.247.94 dev ppp1 proto kernel scope link src 81.173.237.84 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.1 default via 195.14.247.94 dev ppp0 I want 192.168.0.2 to connect to the internet by ppp1 and all

Hello, I have tested a simple thing in two version of Linux and there was a problem when I have used fwmark as a selector for rule lookups. As you can see below on the Slack, the <test> table doesn''t have any label about fwmark. Is there an iproute problem? -------------------------------------- # cat /etc/fedora-release Fedora Core release 2 (Tettnang) # uname -r 2.6.5-1.358 #

Hello! This arguments never run on my system, but I need this: #!/bin/bash -x echo "1" iptables -t mangle -p tcp -d 0/0 --dport 80 -j MARK --set-mark 2 echo "2" echo "201 T1" >> /etc/iproute2/rt_tables echo "3" ip rule add fwmark 2 table T1 echo "4" ip route add default via 192.168.21.2 dev eth1 table T1 echo "5" ip route

Hi. The task: 1. There 3 servers and a router with 2 PPPoE connections (let call them: ppp0, ppp1). 2. There are several groups of Inet-clients to be served (Servers, Clients and Club). 3. The task is: - to route Club through the ppp1; - to Servers and Clients through ppp0; (Next is reproduced from memory and may be slightly incorrect) router # netstat -nr Kernel IP routing table

Hi list, I have tried google but just cant get this to work or figure it out. My setup ======== vanilla 2.6.13 kernel with CONFIG_IP_ROUTE_MULTIPATH=y CONFIG_IP_ROUTE_MULTIPATH_CACHED=y CONFIG_IP_ROUTE_MULTIPATH_RR=y CONFIG_IP_ROUTE_MULTIPATH_RANDOM=y CONFIG_IP_ROUTE_MULTIPATH_WRANDOM=y CONFIG_IP_ROUTE_MULTIPATH_DRR=y My configuration: A host with two ppp links. Ontop of these two ppp dialup

Hello all, I am going through the LARTC howto to understand how the iproute2 works. But some concepts like Policy Routing, RPDB etc are not clear to me. I am pretty new to iproute, beeing using route command for long... From what I understand 1. rules (ip rule) tell how to select packets for routing and route (ip route) tell where to route the selected packets. 2. A collection of rules is

Hi all! I''ve got 2 (soon 3) internet connection. 1 - via ADSL, 2(and3) via ppp My network: http://desima.objectis.net/network-diag linux1: user1.user2 eth0=192.168.1.1 ppp0=192.168.5.2( gw 192.168.5.1) gw=192.168.1.2 ( thru ADSL) compA=192.168.1.6 compB=192.168.1.15 gw2=192.168.1.217 via ppp to different ISP All works for compA and CompB, user1 should use default gw(192.168.1.2)

Hi all !! I would to like to mark and route some kind of traffic (ie: outbound www, now by simplicity) ---inet1--------eth0------------| | | linux | --eth1------- clientes ---inet2(90.0.0.1)--------eth2-| | I have eth0 and eth1 bridged (eth2 is not bridged). I would to route www outbound clients

Hi all !! I would to like to mark and route some kind of traffic (ie: outbound www, now by simplicity) ---inet1--------eth0------------| | | linux | --eth1------- clientes ---inet2(90.0.0.1)--------eth2-| | I have eth0 and eth1 bridged (eth2 is not bridged). I would to route www outbound clients

Hi, Host A has two interfaces: eth0, tap0. I want that all locally generated traffic from user 1004 goes through tap0. This is what I did: iptables -A OUTPUT -t mangle -m owner --uid-owner 1004 -j MARK --set-mark 2 echo 202 bigmac.out >> /etc/iproute2/rt_tables ip rule add fwmark 2 table bigmac.out ip route add default via 10.0.0.1 dev tap0 table bigmac.out ip route flush cache

I've managed to configure a LVS Cluster to act as a transparent proxy squid farm, with a virtual server as load balancer, and three real servers. Because redirecting packets going to port 80 to port 3128 of squid in the load balancer doesn't works, the solution has a mix of ip route and iptables. Here is the script I wrote to configure transparent proxy. #!/bin/bash #Transparent proxy