similar to: Traffic Shaping over Satellite Internet

I''m trying to shape traffic on a Devil-Linux box. This note was originally sent to their maillist, because the LARTC list appears to have been down for the past few days. My mailbox was just flooded with a half dozen or so confirmation requests in response to my repeated attempts to subscribe to this list. ---------- Forwarded message ---------- From: drew einhorn

----- Original Message ----- From: Michał Joachimiak To: lartc@mailman.ds9a.nl Sent: Tuesday, July 20, 2004 3:45 PM Subject: HTB - Really Big problem Hello everybody! Since week i dig lists and www and can''t find solution for my problem. I''m using HTB 3.13 kernel 2-4-25 smp iptables 1.2.9. I''ve got situation like this: LAN------Linux Box(routing only)------- Linux

I''m a new comer. I have problems using tc+htb. I run the following commands, and expect outgoing ssh flow goes into 1:11. But actually it goes into default 12. What''s wrong? tc qdisc add dev eth0 root handle 1: htb default 12 tc class add dev eth0 parent 1: classid 1:1 htb rate 1000kbit ceil 2000kbit prio 1 tc class add dev eth0 parent 1:1 classid 1:11 htb rate 100kbit ceil

hello, I have working htb system with about 1000 users. Until now I reload all rules at change, but it take too much time to apply. I cannot delete applyed filters. There is rules for one user: #!/bin/bash -v # Download shaper EX -> 2:20 /sbin/tc class add dev eth2 parent 2:20 classid 2:1775 htb rate 8000Kbit ceil 10000Kbit quantum 1514 /sbin/tc qdisc add dev eth2 parent 2:1775 sfq perturb

Hello, I have recently started looking at tc and iptables. I have an htb-queue with two classes 1:10 and 1:20 where 1:20 is the default. Then I use iptables to mark all packets I send out on eth1. I then filter marked packets into class 1:10. I expected all packets sent on eth1 to end up in class 1:10, but some packets still go to 1:20. Did I do it wrong? Thank you for any help. regards, David

Hello list. I''ve configured a very simple script to slow down packets coming from a particular IP Address. I''ve used IPTABLES to mark traffic coming from this IP Address, but it does not appear to be working as expected. Let me first describe my system as maybe what I''m doing is beyond what NETFILTER can do. I have one machine that runs all my servers as

I''m trying to shape each machine on an interface to 256k each, but I''m getting stuck and only able to shape an entire interface to 256k. What should I be doing differently here? tc qdisc del dev eth0 root tc qdisc add dev eth0 root handle 1: htb default 10 tc class add dev eth0 parent 1: classid 1:1 htb rate 100MBit ceil 100MBit tc qdisc add dev eth0 parent 1:10 handle 110:

I have 2610 XM with 1 Fastethernet and VIC2-2BRI. Dialin and dialout over pots is ok. Also inbound pots calls get redirected to Asterisk y.y.y.y So far so good. But I want to setup VOIP sessions with local carrier. I added dial-peer 40 for this. Session target x.x.x.x But calls will always get routed to the pstn peers 50 and 60. Peer x.x.x.x is never contacted or tried. My situation: PSTN

Hi! Is it HTB fully compatible with BOND interface? I have this setup (mode= fault tolerance) : BOND0 -> ETH0 + ETH1 BOND1 -> ETH2 + ETH3 ( http://www.kernel.org/pub/linux/kernel/people/marcelo/linux-2.4/Documentation/networking/bonding.txt ) HTB work very well with Class over BOND0. If I add Class for BOND1 it generate balance errors. Also with HTB.init

Hello At first I must tell you that I´m a real newbie with Linux (and english as well...) I´m using 2 vlans and shaping works quite well without vlan Now I want to do load balancing at these vlans. Any vlan should get the same minimum/maximum bandwidth of download and use the bandwidth that isn´t used by the other one at the moment. But with vlan the shaping doesn´t work. Can you please tell me

Hello, I use rrdtool to graph the traffic in the different classes on an interface, eth1. Basically, I use the output from tc -s qdisc ls dev eth1 my tc script (which is only for testing the graphing) looks like this: /sbin/tc qdisc add dev eth1 root handle 1: htb default 20 r2q 1 /sbin/tc class add dev eth1 parent 1: classid 1:1 htb rate 200kbit burst 15k /sbin/tc class add dev eth1 parent

Hello, I have problems with htb. The problem is that when I download any file via shaper with htb, the traffic is very dinamic, it jumps, for example: if i have set ceil = 128kbit the results that it jumps from 112kbps to 144kbps or smth like that maybe its not very bad, but when the traffic drops down to 40kbps or less and then after 1 or 2 seconds jumps to 144kbps, its bad :-( and it is often.

Hi I have tested with FC3 but iam not able get any good results on that. in the list some one recomend me that > 3.17 HTB should work I saw latest FC4 test2 has the HTB 3.17 with iptables 1.3.0 i have install in my P4 box, and trying to test when iam uploading its working perfect, but when iam downloading its going to default class can some one experinced the same problem below is the my

Hello, I''ve just recently started to use IMQ and I got puzzled after seeing the imq usage example on the linuximq.net site: It was something like this: tc qdisc add dev imq0 handle 1: root htb default 1 tc class add dev imq0 parent 1: classid 1:1 htb rate 1mbit tc qdisc add dev imq0 parent 1:1 handle 10: htb default 5 tc class add dev imq0 parent 10: classid 10:1 htb rate 256kbit

Hello i''m having some issues trying to match packets using iptables mark, iproute filter and tc filter.- i mean, when i do iptables -t mangle -A INPUT -p tcp --dport 80 -j MARK --set-mark 20 iptables -t mangle -A PREROUTING -p tcp --dport 25 -j MARK --set-mark 10 iptables -t mangle -A FORWARD -p tcp -i eth0 -o eth1 --dport 25 -j MARK --set-mark 10 $TC qdisc del dev $INET_IFACE root $TC

Hello! I have a quite complicated setup. In my network on each interface there is bandwidth limitation for each user. Booth outgoing (on interface itself) and incoming (attached IMQ) traffic. There is main HTB class which limits bandwidth for whole interface and HTB subclasses for each user. Filtering is done with hashing filters. This setup was working correctly. But now in the network I

Hi, Thanks for the reply. Thats where the problem starts. If I set ppp0 as the default gw the internet doesnt work anymore. This is how im doing it... route del default route add default gw 217.32.81.74 dev ppp0 if I put it back to ppp1... route del default route add default gw 217.32.68.73 dev ppp1 It works fine again. Whats up with that? Cheers, Chris ----- Original Message

I try to shape traffic using HTB and mark packets within iptables using PREROUTING. But the filterrules seems to ignore the marks set with PREROUTING Only POSTROUTING marks are accepted. First my configuration I have a router connected to the internet via ADSL over interface ppp0. eth0 is a tunnel to ppp0 and eth1 serves the LAN. LAN is 192.168.57.0/24 on 10Mbit ppp0 is 80.126.16.44 on

Hello all, I have set my QoS solution and now I am facing a little problem... When I ping to my server it has some lost packages: Estatísticas do Ping para 172.30.0.1: Pacotes: SENDED = 1029, RETURNED = 880, LOST = 149 (14% de perda), Aproximar um número redondo de vezes em milissegundos: Mínimo = 0ms, Máximo = 686ms, Média = 105ms If I disable my QoS ping stats to be ok. I even have

Hello guys, I past the last days trying to configure my shorewall 4.06 firewall to allow openvpn bridging connection. My scenario is the following: roadwarrior (openvpn client) -------------> Internet ------------> (X.Y.W.Z - eth0) Firewall/Gateway (10.x.x.254 - eth1) --------> Local Lan -------> OpenVPN Server (10.x.x.249 - br0) where 10.x.x.0-254 is my private lan X.Y.Z.W is