similar to: tc filter matches ip fileds inside pppoe frames

helo again. I think this question i am asking is worth: we know that pppoe-server creates a pppX device on each connection done to it. So, when i have to shape, i have to shape each pppX connection device on itself alone. What i know is that the borrowing method on one device by itself, e.g. ppp0, alone using HTB or the like. this means that i have to create for another device, e.g. ppp1,

My Internet gateway is using ADSL PPPoE connection with dynamic public IP assigned by ISP. My Internet gateway is Redhat AS3 U2, shorewall 2.0.9 As my ISP provided 4 simultaneous pppoe dailup connection for the same physical adsl line. My linux server can be configured for multiple pppoe connection i.e. ppp0, ppp1, ppp2, ppp3 Is it possible of shorewall to assigned say ppp0''s IP is

I need basic PPPoE startup help. adsl-start DID bring up my PPPoE link (ppp0) to my ISP over eth0 via the DSL modem/bridge. My IPv4 CIDR block is routing and Shorewall is doing the firewalling. But shorewall has to be started after ppp0 is up and working. For now this means running shorewall restart (or start?). Shorewall 4.2 will have a way to restart shorewall without recompiling, I

I am a newbie to linux and shorewall. I am reading the shoreall quickstart guides. I am a bit confused about the following statement: ----------- quote -------------- The firewall has two network interfaces. Where Internet connectivity is through a cable or DSL "Modem", the External Interface will be the ethernet adapter that is connected to that "Modem" (e.g., eth0) unless you

hi all. i am currently now serving PPPoE in my area. i had a script generated from tcng that worked perfectly before i started serving PPPoE. the issue is not in the script it self BUT in that "tc" code is not shaping on the ethernet anymore BUT INSTEAD on the pppX devices. I tested it and talking jargon, what should i do? The issue is that for each PPPoE login, PPPoE-server

My provider is getting ready to switch my DSL router to bridging mode and I supply the router (so I can get no only IPv4 addresses but also IPv6 addresses!). Here are his 'instructions' to me: "Basically you start pppoe, I give you the username and password for it, and then I set the router to passthrough modem mode, and you initiate the PPPoE session directly with my LNS back

Greetings, I've just upgrade a home server to CentOS 6.5 with a new dual-core processor and mobo. I see that with the CentOS 6.x release rp-pppoe can be run as a daemon. I've looked through some online one-page setup notes for rp-pppoe, but nowhere is there a discussion of running it as a daemon. Until now, I've cobbled an ifcfg-ppp0 file and placed it in

Hola, Can someone please point me to the right direction on how-to set up proper routing on PPPoE connection and multiple external IP''s. Thank you kindly. ~Andrew Nady.

Hello, My system is: Server with Slackware 8.1 LINUX, ADSL Internet with PPPoE connection, and I masquerade my LAN. I use "Roaring Penguin" PPPoE client for my ADSL connection. I would like to connect another ADSL line (also PPPoE) to my server and have two lines, because I want to make "Simple source policy routing", as described in LARTC HOWTO. How should I set up my

I need some suggestions, I want to limit the up and down bandwidth of PPPoE users that are terminated on a Linux router (kernel 2.6). What are my options, can I apply tbf qdisc on a ppp interface? That would limit the download, what about the upload? Any suggestions are welcome. -- damjan | дамјан This is my jabber ID --> damjan@bagra.net.mk <-- not my mail address!!!

Hi all, I have a little problem with my home-made slackware linux server. Here is the scenario: 1. I have a local wifi network 2. my server do masquerading and exit in internet via a PPPoE connection Goals: 1. not use SQUID 2. shaping the traffic with classes 3. emule connection must have minimum priority and a band-limit of 10KBytes/s in uplink (server--->internet) Any idea? Thx, Diego --

I am having a little trouble getting my head around this so any help would be appreciated. I have just signed up a new service and have been allocated the following subnet which gives me 30 usable IP addresses. 210.15.xxx.192/27 The connection is made via pppoe which works fine and the connection creates ppp0 and assigns 210.15.xxx.193. Now I want to use 4 IP''s in a DMZ and the reset

Hi all I get a Cisco 1841 router, connecting the office through a CHAP PPPoE link: [...] interface Dialer1 ip address negotiated ip mtu 1492 ip nat outside ip virtual-reassembly encapsulation ppp ip tcp adjust-mss 1452 dialer pool 1 dialer-group 1 no cdp enable ppp authentication chap callin ppp chap hostname username at isp ppp chap password 0 s0meStr0ngP4sswd [...] As

I am building a CentOS 5 box to ship to Houston which will be a gateway system on an SBC DSL connection for a while until the client gets a T1 installed. I have read up on using adsl-setup and related software, but never done PPPoE on anything but LinkSys commodity boxes. I have examined the adsl-setup script, and I think I understand how this works, but want to be sure I understand things

My telco is moving to feeding me over fiber, breaking out with a media converter to one Ethernet interface. At present, I am retaining the static feed over copper on eth0, and taking the two new feeds via vlans on eth1. I have configured the static IP feed on eth1:790 as vlan 790, and that seems to be fine, and eth1:780 as the PPPOE feed, and brought up PPPOE to give me an IP, that is

Hi, I want a way to traffic shape pppoe encapsulated pkts based on its src/dst Ip address. Is there any way I can mark pppoe encapsulated pkts? Samit

I have three ADSL lines that I''d like to use as one big pipe to the internet. The ADSL service works by establishing a pppoe connection (the ADSL "modem" is a bridge), and each pppoe interface gets its own IP address. This means I''d have to have 4 ethernet interfaces (3 for each of the ADSL modems and 1 for the LAN) in my gateway. I''d setup the gateway to NAT

Hello all, I am trying to make a little bit more complex QoS/Shapping form and I need to shape a PPPoE conection that I serve to my clients. So this is the scope: client connects using pppoe so it gets an IP address (from pppoe pool) and open an interface into my linux box interface for this client is ppp0 client has got an ip 1.1.1.2/32 and it is poiting to pppoe-server 1.1.1.1 So,

Hi all, I'm trying out bridging for my wireless and wired LAN, so that they can both use my PPPoE connection. Here's the network structure, pretty easy: darjeeling (192.168.1.7) ringo (192.168.1.3) (mtu 1500) (mtu 1500) \ / \ wlan0 <--br0 (mtu 1500)--> eth1

Hi, I am having problems establishing an adsl connection in dom0 (but ONLY in dom0, without xen everything is ok). Following is my setup/situation: 1. Installed clean Fedora 7 (with virtualization option selected) 2. Booted with the non-xen kernel & setup adsl. Adsl connection works without any problems. 3. Rebooted with xen kernel into dom0. 4. adsl connection can no longer be activated