similar to: Linux as a multicast router

I need to send multicast traffic through a GRE tunnel between two Linux routers. The tunnel works for normal IP packets, but I can''t see how to make it work for multicast. Here''s the setup: 10.10.10.0/24 LAN-B--------------RtrB-------------RtrC--------------LAN-C 192.168.2.0/24 192.168.1.0/24 RtrB interfaces: eth0

Hi, Whilst doing some QA work on XORP on my desktop, which has fxp0 and msk0, fxp0 got totally hosed. I was running PIM-SM and IGMPv2 router-mode on the box at the time. I wonder if this is related to the problems with fxp multicast transmission I saw back in April. I'm a bit concerned about this as fxp is still a very widespread and useful network chip. I am running

Hi, I got this error when i tried to type for some of those. "sysctl: unknown oid...." any idea.. my server seems to be very lagged, where else the network connection seems fine, i think BSD itself as my other redhat box is fine. What else can i do to get optimum protection. Thanks. ----- Original Message ----- From: "Per Engelbrecht" <per@xterm.dk> To:

Hi, my ISP is streaming some local concert using UDP multicasting. I followed the instructions on the site which described how to set VLC in order to view the stream, but it didn''t work. I am behind a Linux router/firewall doing NAT. Using google, I quickly found out that the netfilter/conntrack code doesn''t support NATing multicast traffic. I thought about bridging the internet

I am trying to set up my Shorewall box to forward multicast packets to my local net. I do have some problems with mrouted (see below), but I can join and add routes using smcroute. Multicast works when shorewall is disabled. I got a lot of help from the following. http://lists.shorewall.net/pipermail/shorewall-users/2005-January/016674.html I cannot get the multicast packets to pass the fw when

How do the Multicast routers sniff IGMP/MLD messages from the network? I checked the XORP, pimd etc. Most of them just open a RAW socket with protocol set to IPPROTO_IGMP. But using this the router gets the packets addressed to 224.0.0.1 only. How does it receive IGMPv2 and IGMPv3 membership reports sent by other hosts? Thanks, Sachin

Hi folks, I have set up a cluster on CentOS 5.2 using /etc/cluster/cluster.conf - and it works fine. It's only purpose is to switch a virtual IP between two routers. Now the service is running, I can ping the virtual IP from outside - but this virtual IP is not bound to any interface. How does this work? Can I force the cluster to bind it to a certain interface? I need this because the

well, once i figured out what to do it was easy. 1) install freebsd over linux. 2) recompile kernel with: option MROUTING 3) start mrouted 4) go get yourself a cold beer. you deserve it! thanks! -bob CONFIDENTIALITY NOTICE: The information in this electronic mail transmission contains confidential information intended only for the use of the individual or entity named above. If the

http://bugzilla.netfilter.org/show_bug.cgi?id=536 pavlin at icsi.berkeley.edu changed: What |Removed |Added ---------------------------------------------------------------------------- Severity|trivial |blocker Priority|P2 |P1 ------- Comment #1 from pavlin at icsi.berkeley.edu 2008-12-19

I have a standard 3 interface shorewall setup and I want to receive multicast stuff from ''net'' -> ''loc''. This requires me, first, to do an IGMP join which involves 192.168.1.x -> 224.0.0.x being NATed out as the ''net'' interface''s IP address. Obviously replies have to be NATed back to ''loc'' addresses. Can

Hi, I have been reading: http://lartc.org/howto/lartc.multicast.html in effort to understand how to route multicast traffic and just joined the group. History: I am trying to multicast mpeg (using the videolan server) on a private network. The server side of the network is copper gigabit, which connects to one of those cheap fast Ethernet switches with a single gigabit uplink. The problem

Hi, I have problem with multicast routing on my network. I tried mrouted and also pimd, but always same problem. When I set mrouted or pimd on one router, everything works fine, but when I start mrouted/pimd on another one, routing die. In moment when I start anorher mrouted/pimd /proc/net/ip_mr_cache is cleaned. My topology: gateway (no mrouted/pimd)

Hello, After a few of us have spent a week google''ing around for answers, I feel compelled to ask this question: how do I stop packet loss between my dom0 and domU? We are currently running a xen-3.3.0 (and have tried with xen-3.2.1) on a Gentoo system with 2.6.18 kernel for both domU and dom0. We have also tried a 2.6.25 kernel for dom0 with exactly the same results. The goal is to

hi alli hope you are all fine,I post this mail with the hope i will find an explanation for my too problems. i ''m actually working on an internship subject about xen technology: i*nstall xorp router in the virtual domain of the xen hypervisor.* this installation should be done on a PC with too NIC. The problem is that i don''t know what is the utility of too NIC in such

The documentation is very clear that multicast over tinc does not work in router mode. Why?

On Fri, Dec 14, 2018 at 11:13:55PM +0100, Lars Kruse wrote: > I am a happy user of tinc in multiple environments. It is beautiful - thank you! > > Today I noticed that a network of around 20 nodes suffered from a flood of > packages like the following: > IP6 fe80::e4eb:74b6:57e0:c3e1 > ff02::2: ICMP6, router solicitation, length 8 [...] > Most of the tinc nodes use v1.0.31.

Hi, I have seen http://www.tinc-vpn.org/pipermail/tinc-devel/2010-October/000473.html and so tried out for myself to see if multicast would work in tinc using routing mode. I'm using tinc 1.0.19. My test involved sending a ping out on 224.1.1.1 (as 224.0.0.0/24 is a special case), and while I could see the traffic reaching the other tinc daemons, it never seemed to go out to the local

Hello, I am a happy user of tinc in multiple environments. It is beautiful - thank you! Today I noticed that a network of around 20 nodes suffered from a flood of packages like the following: IP6 fe80::e4eb:74b6:57e0:c3e1 > ff02::2: ICMP6, router solicitation, length 8 For the first ten hours these nodes (even the usually completely idle ones) have seen incoming traffic of around 1 MBit/s

Hi, I found that in some cases llvm generates duplicate loads of double constants, e.g. $ cat t.c double f(double* p, int n) { double s = 0; if (n) s += *p; return s; } $ clang -S -O3 t.c -o - ... f: # @f .cfi_startproc # BB#0: xorps %xmm0, %xmm0 testl %esi, %esi je .LBB0_2 # BB#1: xorps

Hi When I start shorewall, the multicast stream is stopped. My config: Windows VLC Client-----eth0:192.168.254.1/24--fw---eth1:191.168.254.254/16-------------------------Linux VLC Streaming server 192.168.254/24 lan wan (but it''s really a internal lan !) 191.168.1.21/16 on the FW/shorewall route add -net 224.0.0.0 netmask