similar to: lc shaping in- and outbound traffic on same box

Hello, I am creating a configuration where a Redhat server running bridge-tools 0.9.5 will be bridging between different VLANs on the same physical interface (for example: a bridge consisting of eth1.100 and eth1.110). This physical interface is being connected to modern Cisco switches running PVST+. The Cisco switch does not like this configuration as the tags on its BPDUs are being changed

Hi, Is there any tested good HTB script for traffic shaping available like as that of CBQ available at. http://freshmeat.net/projects/cbq.init I am n new bie and need to work on htb. -- Regards, M Arman _______________________________________________ LARTC mailing list LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

Hello, I have 2 dual CPU Xeon 3Ghz HT enabled Linux routers and each one of them serving 2 class C with pick traffic on router about 300Mbit full duplex 2 x Ethernet controller: Intel Corporation 82546GB Gigabit Ethernet Controller (rev 03) 1GB ram And 2 x Ethernet controller: Broadcom Corporation NetXtreme BCM5703 Gigabit Ethernet (rev 10) 1GB ram Both routers have about 600

Hello, I have been using tinc for quite a while now and am very pleased with it. Thanks a lot to everyone involved in the project! I am running a VMware ESXi server in a datacenter that provides some services for me. The virtual machines are connected with different networks running on separated VLANs using VMware vSphere port groups. In order to use the services from my home network, I had the

Hello, does anybody know if quagga for CentOS 5.3 is compiled with -enable-multipath? I want to implement ECMP over 2 ISP. Thanks, Cristi Carstea

Hello All, Does anyone happen to be running Quagga on CentOS 5 with SELinux in enforcing mode? Have you had to create SELinux policies or did it "just work" out of the box? (I'll get around to building this out on CentOS 6 as well.) I'm simply trying to write my config (for the zebra daemon) and it can't be written... Looks like this bug from Fedora 8 in 2008 [0] remains

Hello! I have trouble with multipath routing. Those options are enabled in kernel: [*] IP: policy routing [*] IP: equal cost multipath [*] IP: equal cost multipath with caching support (EXPERIMENTAL) <*> MULTIPATH: round robin algorithm But issuing: ip r a 1.2.3.0/23 scope global equalize nexthop via 80.245.176.11 \ dev eth0 weight 1 nexthop via 80.245.176.13 dev eth0

Hi Guys, I''m trying to compile IMQ with kernel-2.4.26 and iptables-1.2.9 and I want to know is this procedure is correct: ---------------------------------------- - In Kernel 2.4.26 Directory (/usr/src/linux) # cd /usr/src/linux # wget http://www.linuximq.net/patchs/linux-2.4.24-imq.diff # patch -p1 < linux-2.4.24-imq.diff - In Patch O Matic Directory

I was wondering if anyone is running Quagga on Xen? What is throughput/latency like? Was looking for about a gig of mixed packet size BGP throughput. Hardware is Opteron 4 Way Quad cores, was thinking paravirt with a couple of dedicated cores and maybe the addition of Solarflare 10GB Direct IO NICs might give the required performance level but I am unsure. The other option is multi-queue Intel

Hi, I''ve setup quagga on a shorewall firewall server. The only purpose for this is to use BGP to connect to a "peering platform" supplied by our data centre supplier. There are some very large ISP''s (and other various providers including google) on this peering platform and connecting to it will speed up access to/from our services and hosted servers. The physical

I''ve followed this list for quite a long time and have even posted a couple of times. I used the early versions of IMQ from Devik (I think that was his name), and it worked well. I only ever got the chance to implement it in my test environment. I now need to implement it in my production environment. My Linux core router has nine interfaces and has a 27 megabit connection to the

I checked by Alpha this morning after it's been running fine for a while and saw this on the terminal (hand transposed): Jun 14 08:54:55 erwin getty[2087] : getty : retreiving gettytab entry 'default': Device not configured Jun 14 08:54:55 erwin getty[2087] : getty : retreiving gettytab entry 'Pc': Device not configured Jun 14 08:54:55 erwin getty[2087] : getty : retreiving

Hello, Some time ago I''ve read somewhere that local traffic in IMQ could hung up the whole system but it was corrected long time ago. So I was very surprised yesterday when it occurred not true. While testing IMQ I''ve observed for some time that - if you tag some local traffic with iptables both in pre- and postrouting - kernel is hunging up. It is happening quite quick with

Hey, I have a very trivial parsedfile based type - http://pastie.org/311146 - that works fine when deployed and run under puppetd -t. However, when being run by the daemonized puppet, it results in this error: Mon Nov 10 03:50:48 +0000 2008 //Node[ams-proxy-2]/quagga/Quagga::Daemon[zebra]/Quagga_service[zebra] (err): Failed to retrieve current state of resource: No ability to determine if

Hi all, Having a bit of a problem with portupgrade on a -STABLE machine: [root@erwin]/root: portupgrade -aRn ---> Session started at: Tue, 27 May 2003 22:54:00 +1000 closed stream ---> Session ended at: Tue, 27 May 2003 22:54:01 +1000 (consumed 00:00:01) [root@erwin]/root: pkgdb -F does the same thing. Any clues? cheers, Rob [root@erwin]/root: uname -a FreeBSD erwin.number6

Hi there, -- Christian Lyra PoP-PR/RNP _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users

Thanks for the very prompt reply. I''ve been googling already for a few days now trying to understand how bandwidth management works. I came to understand that TC is a utility that I can use to shape up my local network bandwidth consumption. Im hoping I will be guided here through. Here are my questions: 1. Is TC works on an interface of a physical device only? 2. My objective is to

Dear Philipp, I've compiled it from source on my raspberry pi, and replaced the binary from the synaptic package manager with the compiled one. Everyting is working fine now, it seems that there is indeed a "faulty" package in the repository. I don't know who I should contact to get this fixed? Anyway, it works, but while using ogg as output stream from mopidy, I get a delay of

I tried require ''url_writer'' but this is not the trick what should be required/included to test the routes urls ? thanks erwin -- You received this message because you are subscribed to the Google Groups "Ruby on Rails: Talk" group. To post to this group, send email to rubyonrails-talk-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org To unsubscribe from this

Hi all, my IMQ device works OK (thanks to Andy Furniss), but now I''ve problems to attach the traffic in the qdisc''s. This is my conf: ----------------------------------------------------------------------- INET | |eth0 300Kbps ROUTER (NAT) |eth1 | LAN ----------------------------------------------------------------------- MAX=300 tc qdisc add dev imq0 root handle 1: htb