similar to: HTB and bursts

----- Original Message ----- From: Michał Joachimiak To: lartc@mailman.ds9a.nl Sent: Tuesday, July 20, 2004 3:45 PM Subject: HTB - Really Big problem Hello everybody! Since week i dig lists and www and can''t find solution for my problem. I''m using HTB 3.13 kernel 2-4-25 smp iptables 1.2.9. I''ve got situation like this: LAN------Linux Box(routing only)------- Linux

I have htb on 486 sx with 16mb ram. Slackware 9.1. Connection : dsl 1Mbit. 486 works as router and trafic shaper for network made of 12 pc''s. it does the job quite well, but when i play Counter-Strike or connect to my 486 via ssh (on lan), i get huge lag every 11-20 sec. when i connect to 486 via ssh and run iptraf program i see all the trafic, and after a while when lag comes the

Dear All, I’m working with Fedora Core 3, kernel 2.9.1, MPLS-for-Linux-4.193, and having some problems when create a HTB queue. ALL packets goes to the default queue, they don’t care about any mark or ip field I use to enqueue them. : -/ That’s the deal, all packets that incoming the interface eth2 are classified and have theirs TOS field changed following some qos policy at the PREROUTING

Hello, I use rrdtool to graph the traffic in the different classes on an interface, eth1. Basically, I use the output from tc -s qdisc ls dev eth1 my tc script (which is only for testing the graphing) looks like this: /sbin/tc qdisc add dev eth1 root handle 1: htb default 20 r2q 1 /sbin/tc class add dev eth1 parent 1: classid 1:1 htb rate 200kbit burst 15k /sbin/tc class add dev eth1 parent

Hi, Is it possible to attach another qdisq under a HFSC classfull ? I try it and the configuraton works : $TC qdisc add dev $dev root handle 1: hfsc default 30 $TC class add dev $dev parent 1: classid 1:1 hfsc sc rate ${RATE}mbit ul rate ${RATE}mbit $TC class add dev $dev parent 1:1 classid 1:10 hfsc rt umax 1500b dmax 30ms rate 200kbit $TC class add dev $dev

Hi everybody! I''ve been trying with htb and tc filter. It seemed to work fine, but after testing with ethloop I''ve realized that traffic is not being distributed through the leaves as I thought. When sending packets to 1:10 and 1:11 at the same time, there''s no bandwidth sharing. There''s no traffic through 1:11 until traffic through 1:10 has finished. Though

Hello... Im trying to setup HTB to allow me to shape traffic from two upstreams that meets on single lan0 interface. I prefer to use HTB qdisc within HTB root qdisc for cleaner rules design. Seems that it doesnt work at all. tc -s class show doesnt show any traffic on other classes attached to HTB qdisc. Linux 2.6.20.7 iproute-2.6.20-070313 Weird thing is that tc -s class show that 1: and 2:

I have a network with around 40 /24 subnets that shares a common DSL, this cries out for shaping so here I am trying to make it work as my first tc project. I have managed to cargocult some snippets from this list and tried to come up with a config, but there are a few things that I''d really like some input on: 1) Are the NAT''ed addresses available in the PREROUTING table

Hi, this is a followup to "Problem with HTB and ceil", the problem with the ceiling has been resolved, thanks to the memebers on this m/g. Now I have the problem that packets get into the correct classe with the correct marks but the prios are not respected. I have 4 different classes: 1. voip class / prio 0 / mark 100 / voip traffic 2. ACK class / prio 1 / mark 200 / ACK packets to

Hi Guys After googling a little I couldn''t find the correct answer.. When I use : tc filter add dev eth0 parent 1:0 protocol ip prio 1 u32 match ip dst 192.168.0.11 flowid 1:30 , I can shape traffic to 1:30.( works like a charm) Now instead tc filter I would like to use CLASSIFY as below: iptables -t mangle -A POSTROUTING -o eth0 -d 192.168.0.5 -j CLASSIFY --set-class 1:30 but when I

Hi All, I am using the script below to limit download rates and manage traffic for a certain IP address and testing the results using iperf. The rate that iperf reports is much higher than the rate I have configured for the HTB qdisc. It''s probably just some newbie trap that''s messing things up but I''m buggered if I can see it. The following script is run on the

Hello, I have installed a server with three physical ethernet links and some virtual interfaces: eth0 - 213.215.42.70 eth0:1 - 213.215.42.71 eth0:2 - 213.215.42.72 eth0:3 - 213.215.42.73 eth0:4 - 213.215.42.74 eth0:5 - 213.215.42.75 eth0:6 - 213.215.42.76 eth0:7 - 213.215.42.77 eth0:8 - 213.215.42.78 eth2 - 192.168.1.128 eth3 - 213.215.42.69 All traffic are routed by iproute2 and iptables

Hi all :) I''m new to this list, as I''m new too to traffic shaping ;) I''ve set up an FTP server in my ADSL line and I wanted it to serve as fast as possible as long as I don''t use my outgoing ADSL bandwidth, and I''m currently using HTB for that (succesfully, I must add). The problem is (when the FTP server is serving higher than its

Hello, 1. I currently have a 128kbps cable link to the internet..and I''m sharing this connection with others. I''ve made the following script(for alocating bandwidth depending on the services used: browsing, squid, games like counter-strike, icmp, ssh), which unfortunately isn''t working very well as the response times I''m getting upon pinging the server

Hello. I am wondering if the default (auto-computed) burst and cburst parameters are appropriate values for my application. I have a 100 mbit interface which is connected to a 16 mbit uplink. I am sharing this bandwidth into a set of partitions (tc classes) defined as follows: root class [1:1] |

A note to confirm that "-m physdev --physdev-is-bridged" in the iptables command does enable iptables to work in a bridged environment. I was fighting the same problem and this indeed solved it. Below is my test script running on a two NIC Debian 3.1 266MHz bridge. Before adding the physdev flag, only the "tc filter" commands worked but now the iptables commands also

Hi, I''m fighting seriously with a most simple HTB setup. I''d like to share the incoming 64kbps into 5 and 59 for two different machines under NAT. HTB seems to hold the required limits when ceil is not set (no borrowing), but when borrowing enabled it seems to share equally rather then keeping the specified ratio. My setup is below. A typical output of "tc -s -d qdisc

Hi, My home setup is as following: - 1024/128 kbit ADSL - FC3 I set up HTB to prioritize traffic. I am not very pleased with the obtained results. The scope of my setup is to have some ssh sessions with remote servers while browsing websites and running aMule Nothing complicated (I think... ;). The very high priority traffic (ssh), gets stuck when I start aMule and make an FTP download.

Hi I have the following problem: I''ve created qos script which shapes traffic on outgoing interface eth1. More - less it looks like this : ------------------------CUT------------------------------------------------------ #root qdisc and class for eth1 $tc qdisc add dev eth1 root handle 1:0 htb default 19 $tc class add dev eth1 parent 1:0 classid 1:1 htp ratel ${CEIL_UP}kbit ceil