similar to: two routes, non-permanent higher proiority

Hi all, For some reason VSAT or Satellite Internet services are not mentioned (or searchable) in this list's archives. I thought I'd let you know that I tested Asterisk using IAX (not IAX2) to make a phone call from an analog phone hooked up to an Asterisk system behind a Linksys router connected to a Gilat VSAT satmodem, and it worked. The "other end" (gateway) is a

I''ve set up Traffic Shaping on a Linux Router. Using HTB with SFQ, i''m trying to slow down heavy downloading for 20 subscribers over a 2048 kbit downlink. I''m classifying internet related traffic using iptables marking. bri0 is my local lan bridge, receiving egress traffic destined for subscribers. tc qdisc add dev bri0 root handle 1: htb default 2 tc class add dev

Hi, I need a solution for this case: I have a PC(as server) with 3 (or more) Ethernet ports and 3 (or more) Internet access through each Ethernet interface. (from different ISP''s and with different IP''s of course) I need to download files (using wget or whatever else) through each interface (internet line) separately. For example i need to download "file1" through

I installed the current version of yahoo messenger to Wine. I see the yahoo messenger icon on my desktop but when I click on it nothing happens. Also I'm using Ubuntu 8.4? I'm also new to Linux/Ubuntu so please be patient with me. Thanks! Bye!

Has anyone been able to configure Asterisk to work over 3G? I bought Nokia Cell Phones just for that purpose and they register fine over WiFi and 3G but the quality is just not good enough and sometimes the call just disconnects. I have Allow as: ilbc gsm ulaw alaw -- Co-op Vacation Rentals www.coopvr.com 15218 Summit Ave Suite #300-354 Fontana, CA 92336 Phone/Fax (855) 760-COOP (2667)

Hi, I regularly have errors (kernel: dst cache overflow) and crash of a firewall under Linux 2.6.17 and the route patch from Julian Anastasov. With rtstat I see that the route cache size increases regularly without never decreasing. I have this parameters: fw:/proc/sys/net/ipv4/route# grep . * error_burst:1250 error_cost:250 gc_elasticity:15 gc_interval:60 gc_min_interval:0

On a router, there is no need for and IMQ because there is always an egress path. For example: Internet -> eth1 -> iptables -> routing -> ... -> egress qdisc -> eth0 -> LAN LAN -> eth0 -> iptables -> routing -> .... -> egress qdisc -> eth1 -> Internet Local Process / Proxy -> routing -> iptables -> egress qdisc -> eth1/eth0 ->

Hi, The CBQ config file shud be some thing like this. DEVICE=eth0,10Mbit,1Mbit RATE=50Kbit WEIGHT=5Kbit Shall i hardcode the DEVICE BW as 10/100 Mbit or Shall i use any other tool like ethtool for getting this. ethtool gives Speed: 10Mbps If so, how about, if i use some other Interfaces other than eth0, like ppp0 or some other? C''d anybody can give a suggestion over this? thanks

Hi, Any body having idea to find the NIC Capacity / BW (10 / 100 Mbps) ? Whether the interface may be eth0/eth1/ppp0 or some other. Is there any related IOCTL avialable, if so just give the linux-2.4.18 file path. thanks, Srikanth. _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

Hello, I hope i wont make it too complicated and sorry for my englihs... The company has multiple connections to the internet ADSL + CABLE + XDSL... and i only want to use two for load balancing for now. I have read the HOWTO and i got it up and working it works great but i still have a few questions if anyone could help! the setup is: ADSL on ETH0 and CABLE on ETH1 When i load balance on

Saju Palayur <saju_pa at hotmail.com> writes: > Hi > > > > We have ported the Narrow band 8 Khz Speex encoder and decoder on to TI DSP 5505 > > > > To compress 20ms of 16 bit audio sampled at 8Khz it takes 4.2ms. > > Is there any optimizations I can do to make it run faster. The first thing to do would be to profile the code (I assume you're using

Hello list, I want a set-up with a satellite link (eth0) and a cellular cdma link (ppp0) coming into a linux box with a LAN (eth1 or wlan0) to be able to route first through the satellite when it''s on, or else the cdma when it''s in range. Load sharing is not critical, but it would be nice. The satellite has a static IP, the cdma is dynamic. Both WANs are

Hello all. I have the following code (taken from the depot tutorial then modified) def add_dish( dish, type, qnty ) item = @items.find {|i| i.dish_id == dish.id && i.type == type } if item item.quantity += qnty.to_i else if type == ''Fresh'' item = Fresh.for_dish(dish) else item = Frozen.for_dish(dish) end

Hello, I''ve been using Rails for years, including has_many :through and eager loading, but this one has me stumped. The problem is that Active Record is only eager-loading the first of many records. Here are the models (note set_table_name for a legacy schema): class Tag < ActiveRecord::Base set_table_name ''tag'' end class DishTag < Tag has_many

Could those on the list who have used or tried to use VoIP over a satellite internet connection comment on how well it works or if it even works at all in a reliable way. What is the effect of latency on the VoIP path and how much is generally tolerable? routing via satellite adds about a quarter second of latency to the path. Is that too much? Eric

Dear list, I tried to use the nparcomp to run some post hoc non-parametric comparison and got and error. Error in uniroot(pfct, interval = interval) : f() values at end points not of opposite sign Appreciate any comments. the command line: >nparcomp(Ulceration~Group,data=test,type='Dunnett',control='Non-treated') Jun

Hi! I use simtest fonction of multcomp package to compile a Dunnett's test. I have 10 treatments and one control group, so i create a matrix with: m<-matrix(0,10,11) m[1,1]<--1 m[1,2]<-1 m[2,1]<--1 m[2,3]<-1 m[3,1]<--1 m[3,4]<-1 m[4,1]<--1 m[4,5]<-1 m[5,1]<--1 m[5,6]<-1 m[6,1]<--1 m[6,7]<-1 m[7,1]<--1 m[7,8]<-1 m[8,1]<--1 m[8,9]<-1

Dear R-experts, I need to replace the values of a vector(tx) with a word ('Vehicle') when the value of the vector contains the word 'vehicle'. Sometimes, the value could be 'MCT vehicle', or 'control-vehicle', etc. I tried gsub like this treatment<-gsub('vehicle','Vehicle', tx, ignore.case=T) But then I end up with values like 'MCT

Hello all. I have the following Code in a view: <% @dishes.each do |dish| -%> <tr> <td><%= link_to dish.name, :controller => "restaurant", :action => "show_dish", :id =>"#{dish.id}" -%> <% if dish.vegetarian? -%> <%= image_tag("/images/vegetarian.gif", :class => "bevel", :size => "8x8")

I am working on creating an R package for doing fire department analysis and am trying to create a function that can display emergency incident densities. The following code sort of does the trick, but I need a display that shows the number of incidents per square mile. I believe the code below shows incidents per square unit (in this case, degrees lat/long). To solve this problem, I believe