similar to: Install on a usb flash drive

Hi All, I want to put a ASTERISK BOX bend a Firewall. So I have given below rules. iptables -A FORWARD -p udp -d 192.168.101.30 -m multiport --dports 3478,4569,5060 -m state --state NEW -j ACCEPT iptables -A FORWARD -p udp -d 192.168.101.30 --dport 10000:20000 -m state --state NEW -j ACCEPT iptables -t nat -A PREROUTING -p udp -i eth0 -d 1.2.3.4 -m multiport --dports 3478,4569,5060 -j DNAT

I am trying to plug a USB 2 device in a USB 3 slot. Nothing is being detected in "lsusb". Is there something special I need to do? I am running centos 5.5 x86_64. I thought 3.0 was backward compatible. Nothing special about my device its an RS232 to USB device. It works in 2.0 slot. Thanks, Jerry

Hello guys. I am new in mac world and in wine apps. I have this singular situation: I have a macbook with wine and winebottler installed. I want to use this exe app: azloader.exe. Ok, wine is able to load it normally. But... the problem is, my macbook has not the RS-232 port. So I bought a RS-232 to USB adapter. I've installed the correct "drive" to use that. I've tried that in

Hello Does anybody know if it's possible to monitor a Powercom EBk 500 (RS232)? the trick is that I am using a raspberry pi, it does not have RS232 so I connected a keyspan RS232 to USB adapter, but so far I can?t make this work. Thanks for your time to read this. -Edgar -------------- next part -------------- An HTML attachment was scrubbed... URL:

Is there something in CentOS/linux that would take a single input in my case RS232 port and deliver that to two connecting network ports? So two devices can get the single port data. Thanks, Jerry

I am running linux MEPIS 8 and have been having problems getting smithmicro quicklink mobile to work with wine. It installs fine and runs fine but no USB support will not detect my blackberry to use as a modem and alltel/verizon has no plans (nor does smithmicro) to make a linux version of this any one have any ideas?

Hi everyone, This is not directly NUT related, but i don't know where else I can still ask this. I have been using a pretty decent 2nd hand MGE ellipse premium 1200VA for a while now at home. http://www.mgeups.com/download/doc_intl/ small/premium/389uk.pdf It's been working very well for me on linux, but my linux server has recently passed away and now I only have Macs left.

Is everyone else posting to this list getting one of these after each-and-every post? If so, someone please un-subscribe this person: rsivak at tmo.blackberry.net Phil -------- Forwarded Message -------- > From: postmaster at tmo.blackberry.net > To: Philip.R.Schaffner at NASA.gov > Subject: Delivery Status Notification(Failure) > Date: Tue, 28 Aug 2007 13:32:02 GMT > > Your

Anyone seen this before? ----- Forwarded message from ips at shaw.ca ----- X-Spam-Checker-Version: SpamAssassin 3.3.2 (2011-06-06) on doctor.nl2k.ab.ca X-Spam-Level: * X-Spam-Status: No, score=1.0 required=5.0 tests=RCVD_IN_BACKSCATTER autolearn=no version=3.3.2 X-Original-To: root at doctor.nl2k.ab.ca Delivered-To: root at doctor.nl2k.ab.ca X-Virus-Scanned: amavisd-new at doctor.nl2k.ab.ca

Hi all, Currently, the "megatec" driver only supports UPSes which have a serial (RS232) interface. However, I'm under the impression that most of the models that speak the megatec protocol, and have an USB interface, just have a standard serial-to-USB converter inside. This being the case, there should be a "/dev/ttyUSBx" device which the megatec driver could use just as

Hi all, Currently, the "megatec" driver only supports UPSes which have a serial (RS232) interface. However, I'm under the impression that most of the models that speak the megatec protocol, and have an USB interface, just have a standard serial-to-USB converter inside. This being the case, there should be a "/dev/ttyUSBx" device which the megatec driver could use just as

On 5/28/19 3:39 PM, Julian H. Stacey wrote: > grumpy at mailfence.com wrote: >> a friend gave me an old apc smart-ups 1250 >> it has a rs232 interface but i have no pc with a rs232 port >> i attempted to use a rs232 to usb adapter but the ups goes nuts >> i connected the ups to batteries and verified it was working properly >> when i plug the usb cable into the pc

On Tue, 28 May 2019, nicolae788 wrote: > Apc uses a propietary serial cable and your convertar for sure it's wired > standard. Refer to the following link for info. > https://pinoutguide.com/UPS/apc_smart_cable_pinout.shtml > > Good luck > > On Tue, 28 May 2019, 15:13 , <grumpy at mailfence.com> wrote: > >> a friend gave me an old apc smart-ups 1250

a friend gave me an old apc smart-ups 1250 it has a rs232 interface but i have no pc with a rs232 port i attempted to use a rs232 to usb adapter but the ups goes nuts i connected the ups to batteries and verified it was working properly when i plug the usb cable into the pc the ups shuts down when i attempt to turn it on it beeps twice and shuts down this all occurs before i start the nut software

Hi, What modules are needed in my mkinird command with --preload to boot from usb thumbdrive? THanks, Jerry

Suggestions? ----- Forwarded Message ---- From: James Tucker <jt at ra66i.co.uk> To: djberg96 at yahoo.com Sent: Thursday, October 19, 2006 7:28:30 AM Subject: Win32 OVERLAPPING IO Hi Daniel, My name is James Tucker, I''ve been hacking in Ruby for only a few months now, however am an experienced general programmer in a wide variety of languages. My current focus is on a new

I installed Board Master a software that control a CNC machine to produce PCB (Printed Circuit Board). The software install flawlessly but to check if it works I need RS232 working to control CNC machine. I tried to set connection parameters in Board Master choosing COM1 (the only available) but CNC machine don't move and software keep asking for switching machine on. Of course software and

Hi there Does any one of you know something about R and an implemented RS232-Interface? Are there any packages? Or is it possible to write an extensions or something like that in C/C++ ? The problem is that i should handle the information from a measuring device via the RS232-Interface (probably you know LabVIEW, which provides this functionality). These informations should then directly be

Hi I have PW 5115 500 UPS which has both RS232 and USB connectors. bcmxcp driver works fine with serial connection but bcmxcp_usb does not with USB one. After some USB sniffing on windows box I've found that PW5115 communicates in other way than supposed in driver. Applying attached patch makes driver to work properly. System: FreeBSD 6.2 but ugen driver needs patching in order to respect

Hi James, I'm referring to your post here: http://lists.alioth.debian.org/pipermail/nut-upsuser/2010-September/006201.html Have you got by chance any more info on the Dyamix 1000VA model? I was foolish to buy the USB version because it had a better display on the front. Is there any way to get this to go? I have tried all the USB drivers in NUT (on pfsense 2.0RC1) and none do anything