similar to: voip quality/bandwidth/latency techniques

Hello, I''m having such problem with HFSC with following config: + tc qdisc del dev eth3 root + tc qdisc add dev eth3 root handle 1: hfsc default 2 + tc class add dev eth3 parent 1: classid 1:1 hfsc ls rate 512kbit ul rate 512kbit + tc class add dev eth3 parent 1:1 classid 1:2 hfsc ls rate 2kbit ul rate 400kbit + tc class add dev eth3 parent 1:1 classid 1:3 hfsc ls rate 32kbit ul rate

Hello, I have begun to use the tc scripts since 2 weeks ago, so I am beginner. I am trying to divide my bandwidth in 4 independent ones. Each of these sub-bandwidths is assigned to 4 different groups of ip. Bandwidth sharing is allowed. I put a Linux with two Ethernet card between the router and the LAN. Eth1 is the card connected to the router and eth0 is the one connected to the LAN. My ISP

Hi All, I''m trying to create a contended section of bandwidth using IMQ. I have the imq0 device up and running, with traffic passing through it. Firstly, I need to throttle the entire device imq0 to 2mbit/s. I would then like to add throttle rules for individual IP addresses, allowing them to pass up to 512kbit/s each, as long as imq0 has not reached its 2mbit/s. The configuration

When I start my script: * - Creating classes on br1 for upload control ... * - tc class add dev br1 parent 2:0 classid 2:46 hfsc ls m1 576.0Kbit d 2000ms m2 192.0Kbit ul m2 384Kbit ... [ ok ] * - tc class add dev br1 parent 2:46 classid 2:47 hfsc sc umax 1500b dmax 30ms rate 80Kbit . [ ok ] * - tc class add dev br1 parent 2:46 classid 2:48 hfsc ls m2 152.0Kbit ul m2 152.0Kbit

My hfsc rule .. tc qdisc add dev eth2 handle 1: root hfsc iptables -t mangle -N ms-all iptables -t mangle -N ms-all-chains iptables -t mangle -N ms-prerouting iptables -t mangle -A PREROUTING -j ms-prerouting iptables -t mangle -A ms-prerouting -j CONNMARK --restore-mark iptables -t mangle -A ms-prerouting -p udp --dport 4444 -j MARK --set-mark 1 iptables -t mangle -A ms-prerouting -p udp -m

Hi all, my IMQ device works OK (thanks to Andy Furniss), but now I''ve problems to attach the traffic in the qdisc''s. This is my conf: ----------------------------------------------------------------------- INET | |eth0 300Kbps ROUTER (NAT) |eth1 | LAN ----------------------------------------------------------------------- MAX=300 tc qdisc add dev imq0 root handle 1: htb

now, i''m learning and try to read a lot of article about tc command in linux for setting traffic shaper. but i''m doubt about In the theory about tc command ... In general, we define class under root qdisc but Is it can be possible ???? If we define another qdisc under root qdisc, Can i do it? because i have just read tc command syntax and i found this point ... syntax: tc qdisc

I''m using HFSC to limit bandwidth for our wireless customers. However, I''d also like the bandwidth prioritized based on packet type. This is what I''m trying right now, and I''d just like some input from anyone out there knowledgeable in this on whether it does what I want it to do: Eth1 -> HFSC ........|-> HFSC (User1) (Min 512 Kb, Max 1024 Kb, Burst 1536

Hey Andreas, how i catch this traffic using L7 filter?, i´ve installed l7 filter now, but i don´t kwnow to use the kind of filter...!!! Can you help me? Thx.- Terraja-based 2007/4/29, lartc-request@mailman.ds9a.nl <lartc-request@mailman.ds9a.nl>: > > Send LARTC mailing list submissions to > lartc@mailman.ds9a.nl > > To subscribe or unsubscribe via the World

Hi! I''m trying to shape my internet connection traffic using hsfc and I''ve encountered the following problem (may not be connected with hfsc). on my lan interface I shape incoming traffic like this: tc qdisc add root dev eth1 handle 1: hfsc default 1003 tc class add dev eth1 parent 1:0 classid 1:1003 hfsc ls rate 10kbit ul rate 10kbit tc class add dev eth1 parent 1: classid

Hi, I am new to tc and have been reading quite a bit on how to set it up etc. Everything seems to be working fine, until I started scp-ing a large file over a low bandwidth connection as part of my testing process. Here is the setup: my pc --- bridge running tc/htb --- rest of network TC is filtering traffic from "my pc" and classifies it as 120kbit (see my script below). I then scp a

HTB performance improvement Hi all ! i''m looking at the performance of the HTB algorithm/implementation because i would like more packets/sec !! this is the scenario of the performance test: i''m using an embedded system with: SPEED CPU: 399,999 MHz RAM: 128 MByte FLASH: 16 MByte EEPROM: 8Kbyte PROCESSOR MPC8272 a lan to lan 10/100 and in particular we are sending

i doubt about ruleset in mastershaper demo about why use hfsc at leaf class but inner class use htb??? how different for manage traffic like it???? /bin/false qdisc add dev eth1 handle 1: root htb default 1 /bin/false class add dev eth1 parent 1: classid 1:1 htb rate 2048Kbit ######### Incoming Rules ######### chain HB /bin/false class add dev eth1 parent 1:1 classid 1:21 htb rate 128Kbit ceil

To stress the urgency and importance of my questions, I am willing to pay $100 to the first person that can provide me with the scripts/ rules that will work in my SnapGear firewalls that will solve the problems I am having. Please see the following post: Linux QOS and prioritization of real-time data (RTP/VoIP) Thank you!

Hi: I am using a machine with the 2.4.26 kernel, and trying to compare the performance of the HTB qdisc with the HFSC one. I have the following simple script that allows me to have a video stream on port 1234 while it limits a ttcp UDP stream so that the video stream is unimpaired. #!/bin/bash tc qdisc add dev eth0 root handle 1: htb default 12 tc class add dev eth0 parent 1: classid 1:1

Dear All! I reach the point that I must ask you what I have to do. I am beginner at traffic shaping and I''m very confused with it. :) Here''s my script that doesn''t do what I want to do with it: tc qdisc del dev eth1 root tc qdisc add dev eth1 root handle 1 htb default 2 r2q 10 tc class add dev eth1 parent 1: classid 1:1 htb rate 300kbit tc class add dev eth1 parent 1:

hmm HFSC ? where can i find more informations and examples about the *linux* HFSC ? http://trash.net/~kaber/hfsc/ does not help here -- _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

Hi, tc qdisc add dev eth0 root handle 1: htb tc class add dev eth0 parent 1:0 classid 1:1 htb rate 2000Kbit ceil 2000kbit tc class add dev eth0 parent 1:1 classid 1:2 htb rate 1200Kbit ceil 2000kbit tc class add dev eth0parent 1:1 classid 1:3 htb rate 800Kbit ceil 2000kbit tc class add dev eth0 parent 1:2 classid 1:21 htb rate 600Kbit ceil 2000kbit tc class add dev eth0 parent 1:2

I try to use tc on mips with linux-2.4.18 but the u32 filter dosn''t work I added htb qdisc to linux-2.4.18 and use it to limit the speed in LAN, it only work well on the default class, for example tc qdisc add dev eth0 root handle 1: htb default 10 tc class add dev eth0 parent 1:0 classid 1:1 htb rate 2000kbit tc class add dev eth0 parent 1:1 classid 1:10 htb rate 500kbit ceil 500kbit

Hi all :) I''m new to this list, as I''m new too to traffic shaping ;) I''ve set up an FTP server in my ADSL line and I wanted it to serve as fast as possible as long as I don''t use my outgoing ADSL bandwidth, and I''m currently using HTB for that (succesfully, I must add). The problem is (when the FTP server is serving higher than its