similar to: bridge or vlan

On Thu, Mar 30, 2023 at 09:07:53PM +0200, Hans Schultz wrote: > Not true, it reveals that I forgot to put it in the patch, that's all. As > I cannot run several of these tests because of memory constraints I link > the file to a copy in a rw area where I modify the list and just run one > of the subtests at a time. If I try to run the whole it always fails > after a couple of

Hello Samba experts, Please read all email because i'm desperate!!!!! I have problem on joining to LAN-s using Samba. Finally i got a solution to "see" booth workgroups on "Entire Network", but i'm having problem with stations located in LAN2. From any station located in LAN1, I can see LAN2 workgroup and the browse list with stations located in LAN2, but when

I''m converting my network from a "one interface per segment" to a "single connection with vlans", well, some hardware I have requires using different vlan IDs. suffice it to say I need bridges to connect a few different vlans that should all be one but can''t be because of firmware constraints. so my first step is to get shorewall to know about bridges.

Hi, We have a 256 kbits/s (kilobits per second) link to the internet. it is a router running Linux that belongs to our ISP. They have given us 8 internet ips. (i.e- subnet is 255.255.255.248). one has been given to this router. I have given another internet ip to the firewall running CentOS 4.5. iptables is running on it. And also, I have installed iproute2 pkg as well. pls see below for

Dear Friends, I have been using shorewall for some years. I want to set up "shorewall 2" router behind firewall, accordind to this picture: I have lost at setuping "zone"-s (wifi, lan1, net). Plese help me ! Thanks, psw net | | SHOREWALL 1 ------- lan 1 | | |wifi | | SHOREWALL 2 ------- lan 2 | ---------------- lan 3

An very interesting test did yesterday that, LAN1 and LAN2 setup an tinc VPN which is quite simple(the physical link between tinc nodes are quite stable/fast), and no any application traffic to go through the tinc. Later, I setup smokeping which LAN1 initial 20 ping to LAN2 on a per-minute basis, but as you saw from the below picture, it had packet drop. But if I perform a constantly ping from

 Hello, everybody.  This one''s got me stumped.  What I''m trying to do is have two networks--192.168.1.0 and 192.168.2.0--with SMB and WINS running between them.  So far I can mount SMB shares allright, but I can''t browse by WINS names across the router.  I''ve posted this question on Linuxquestions.org; you''ll find the details there.  Here are my

On Tue, Mar 28, 2023 at 19:40, Ido Schimmel <idosch at nvidia.com> wrote: > On Sun, Mar 26, 2023 at 05:41:06PM +0200, Hans Schultz wrote: >> On Mon, Mar 20, 2023 at 10:44, Ido Schimmel <idosch at nvidia.com> wrote: >> >> + $MZ $swp1 -c 1 -p 128 -t udp "sp=54321,dp=12345" \ >> >> + -a $mac -b `mac_get $h2` -A 192.0.2.1 -B 192.0.2.2 -q >>

Hi, this is my Linux Box ---------------------------- LAN 1 -----|--eth1 <---br1--->eth0.1 | | \ | | eth0--|----- 802.1q tagged 1 Mbps link | / | LAN 2 -----|--eth2 <---br2--->eth0.2 | ---------------------------- I have to bridge the 2 lans

Hi, list members. I''ve been reading a lot about traffic control because at work we have the following configuration...... LINUX BOX _____ 100 mbit | | LAN1--------------|eth0 | | | 2 mbit SDSL | eth1|-------------------INTERNET 100 mbit | | LAN2--------------|eth2 | | | ------- The linux box (REDHAT 9-2.4.20-30.9) acts as a firewall-NAT solution for both

I have the following situation: A Linux 2.4.22 server: Physical ethernet: lan1 - Ethernet port (Internet) lan2 - Ethernet port (Cisco Switch, Trunk port) Tunnel: tap1 - OpenVPN in tcp-server mode VLAN's: lan2.201 lan2.202 lan2.203 tap1.201 tap1.202 tap1.203 Bridges: br201 (lan2.201, tap1.201) br202 (lan2.202, tap1.202) br203 (lan2.203, tap1.203) On the other end, the same type of server:

Hello, I am a newbie in Asterisk IP PBX but I am very impressed by its functionalities. I have read that It can work over IP network and across the PSTN. I am not very sure how it works over the PSTN.. In case if people have not yet the Internet or SDL access, I would like just to know if it is possible to interconnect two IP LANs using the traditionnal analog Network and Asterisk PBX? In such I

Tom, I was upgrading a remote firewall, when upon restart, shorewall found a rule with a wrong zone and decided to not continue and stop itself. The problem now, is I cannot access that firewall over ssh anymore. One suggestion would be to instead of "shorewall stop" to have a basic emergency rule with only ACCEPT:info all all tcp ssh rule instead with DROP all policy. Shorewall could

Hi, I'm using linux 2.6.21.5 and our kernel is freeze. The problem is, if I create a Software bridge using $brctl command. and add two interfaces say, eth0.0 and eth0.1 using $brctl addbr br-lan $brctl addif br-lan eth0.0 $brctl addif br-lan eth0.1 and when i send traffic from a host connected to one port to host connected at other end, soon all the memory is dried up and and kernel

I need to change the host name on a test server, and in the past when I used hostname to change the hostname, it did not seem to change it everywhere. I really don't want to do a rebuild just yet, but I have to feel confident that hostname is really changed (reboot is not too much of an issue). What is the recommened practice? Other than get it right the first time.

Hi, I have a little problem to setup iproute in my network It looks like this: ---- ----- ------ R1 R2 R3 ---- ----- ------ | | | | | | ------------------------------- ETH1 ETH2 ETH3 ETH0 ETH4 -------------> DMZ ------------------------------ | |

Many thanks for the help to date. I now have a working vpn with three nodes: 10.20.30.1 10.20.40.1 10.20.50.1 Each machine can see each other machine 100's of miles apart from each other. Each machine is behind its own router. The machines are on their own subnets, as well, of course. The individual IP's on the lans of the nodes are: 192.168.0.155 (corresponds to 10.20.30.1)

Hello! I've got a problem with DNS,VPN and SAMBA. I do have 3 Linux servers on distinct subnets. (192.168.1.1 ,192.168.2.1 and 192.168.3.1). I have done a VPN between the 3 subnets and I could do a ping from 192.168.1.1 to the others without problems. Each sever has 2 network cards. One of them is connected to ADSL.

Hi, we have a trust relationship between servers in the 2 LAN's of my company, my problem is that (even with problems as I commented in a previous mail) I have somekind of access to the LAN where my Linux machine is connected to, but not to the "trusted" LAN. Could someone give me a hint about how to get this? Any kind of documentation would be helpful.... Regards, Juan

Hey guys! To make the adoption of IPv6 networks with Samba4 more smooth / robust, I think that it is vital to give to Samba4, the ability for it, to join a IPv4-Only Secondary DC, into a Dual-Stacked Primary DC. This doesn't work today. Otherwise, these days to enable IPv6 within a "Samba4 AC DC" network, it is a requirement to enable it, simultaneously, on each and every network