similar to: Network traffic tool

Hello all, I''m reading the nice documentation about shorewall with multi isp. And I wonder about squid (non transparent) and shorewall Can I use on same machine, squid with ldap ident, dansguardian, and shorewall with multi-isp (four or five) ? Perhaps there is a problem because squid mask source IP, shorewall can maintain and load balance sessions for the same source IP ? Thanks Fred

Hey, I have a setup that has one machine communicating to a server using UDP over IPv6. For specifics, it is using collectd with a boosted MaxPacketSize in the network config. What this means is there is some IP fragmentation happening, and that is getting REJECTed. My policy is to REJECT, and I have an ALLOW for the particular communication I want. What I''m getting in my logs is

Hi All! Been quite a few years and lots of water under the bridge but here I am back! I have a customer that has now decided they need a bit more bandwidth over and above their fixed line! They are not in a good area for ADSL because of copper theft and being a bit to far from the closest DSLAM! They have installed a wireless link and I have made certain that put it behind my simple iptables

Hi!!!! somebody have tips for install openvpn-as and shorewall!? thx. ------------------------------------------------------------------------------ LogMeIn Rescue: Anywhere, Anytime Remote support for IT. Free Trial Remotely access PCs and mobile devices and provide instant support Improve your efficiency, and focus on delivering more value-add services Discover what IT Professionals Know.

Hi All! I only ever have complex setups. Customer site has a dedicated leased line from their ISP terminating on a Cisco router. Router is configuered with the first usable address on a /28 network - 196.x.y.73. The linux firewall is configured with the remaining 5 ip''s, 196.x.y.74 to 196.x.y.78 and 79 as the broadcast. Sounds normal but here is the twist. The primary or first ip

Dino, Alexey, there are a number of users suffering issues with your Powercom devices. Could you (Dino, and Keven if possible) please have a look at the below one, from Angela, and check for a fix? I've scheduled to release 2.6.1 next week, and having that fixed is part of the list. 2011/5/16 Angela Williams <angierfw at gmail.com> > Hi All > > On Friday 13 May 2011 at

Hi All! Just an update! The snmp driver seems quite happy with an APC AP9618 managment card in an APC Smart-UPS RT 5000 XL UPS. I have an APC AP9630 to test in the near future so will give and update on that one too! Cheers Ang -- Angela Williams angierfw at gmail dot com Linux/Networking Hacker Blog http://angierfw.wordpress.com Smile! Jesus Loves You!

Hi! Normally nut was just worked and worked for me! Not this time though! Distro is Gentoo withe latest nut-2.6.0 emerged today. Linux kernel version is 2.6.36 UPS is PowerCom BNT2000AT "Driver" is powercom ups.conf looks like this! Okay so APC1 is not and APC! [APC1] driver = powercom type = BNT port = /dev/ttyS1 numOfBytesFromUPS = 16

I''m trying to get TPROXY / Squid running and I have a few questions... I found this page: http://www.shorewall.net/Shorewall_Squid_Usage.html#TPROXY However, it doesn''t explain what I''m seeing in the configuration. For the zone file, do I keep my loc and net configurations and just add the following to the file? - lo - - or do I remove the loc and net zones and

Hi All, Just joined the list to try and solve a problem. To show that I''ve read the rules I''ll start with the requested info os linux kernel-2.4.27 with latest netfilter pom for gre and pptp conntrack etc iptables is 1.3.0 - downloaded and compiled with the pom stuff and the 2.4.27 kernel shorewall version shorewall-2.2.1-2 from rpm ip addr show [root@squid3 root]# ip addr

Hi, I want to configure QoS in my shorewall conf but I have a doubt. Now I am using tcrules with prerouting and with the file providers, like this. 2:P 192.168.0.11 0.0.0.0/0 tcp 25 So, with this way I route my smtp traffic with my provider number 2. Well, now I want to configure QoS with tcclasses and tcdevices, but if I do that I need to use the MARK in the tcclasses So, how

Hi, I have a simple question. I have my firewall with 2 external Ip and 1 lan. For example ISP1 FW LAN----Mail Server ISP2 Ok, when i DANT the smpt port to my mail server, I can see that the conection in my mail server comes from the external IP of my ISP. I need to change this so the conection to my mail server cames from the LAN IP from my firewall Is this possible?

Cannot install logmein.msi and here is what I get: wine start logmein.msi preloader: Warning: failed to reserve range 00000000-60000000 preloader: Warning: failed to reserve range 00000000-60000000 err:dosmem:setup_dos_mem Cannot use first megabyte for DOS address space, please report preloader: Warning: failed to reserve range 00000000-60000000 err:dosmem:setup_dos_mem Cannot use first megabyte

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I mean http://users.gurulink.com/drk/transproxy/TransparentProxy.html on "6. Transparent Proxy to a Remote Box." Thanks - -------- Original Message -------- Subject: Squid on remote Box Date: Wed, 16 Mar 2005 17:16:35 +0700 From: Royke K <royke4k@cbn.net.id> To: shorewall-users@lists.shorewall.net How do I configure port

I''ll take this one next. -Tom -- Tom Eastep \ Nothing is foolproof to a sufficiently talented fool Shoreline, \ http://shorewall.net Washington USA \ teastep@shorewall.net

I installed ntop on a centos5.2 system (which got all yum updates a few days ago)... # rpm -q ntop rrdtool ntop-3.3.8-1.el5.rf rrdtool-1.2.28-1.el5.rf went through the password configuration when I start it, its erroring. # service ntop start Starting ntop: Processing file /etc/ntop.conf for parameters... Mon Nov 24 23:56:36 2008 NOTE: Interface merge enabled by default Mon

Hola Compañeros, Estoy tratando de "contar" utilizando la función tapply y length y obtengo un error que no entiendo. Agradecería su ayuda. Las líneas son las siguientes: UNO <- subset (datos, CRIH2008 == "VERDADERO") dim (UNO) Abund2008 <- tapply (UNO$Cons, list(UNO$Site, UNO$Trat), length, na.rm=T) Y obtengo este error: Error en FUN(X[[1L]], ...) : 2 arguments

I don't know why I haven't signed up for this list before since we use CentOS all over the place. The list is very useful and it is good for me to participate and "give back" to the community. Anywho, I wanted to post this response to a thread that was created back in November 2008 about the ntop daemon failing to start. I'm currently setting up ntop as a NetFlow &

Hola Javier, Muchas gracias por responder tan rápido! Yo trabajo en Mac OS X 10.9.4. Versión 0.98.953 de RStudio. Versión 3.0.2 (2013-09-25) de R. ## Este es el script que estoy trabajando. Se trata de una rutina para automatizar el cálculo de la duración del evento. setwd("/Users/angelacamargosanabria/Documents/ANGELITA/1-DOC/1-TESIS/4-PAPERS/1-Mamiferos/DATOS/Bases") BASE <-

If you are running ntop on 5.4, what compile options? Use ports version? Or surgefile tarball? It makes a great security forensics tools, but I can't get it to stop segfaulting.Was wondering if anyone found a fix for it. -- Michael Scheidell, CTO 561-999-5000, ext 1131 SECNAP Network Security Corporation Take a vacation from spam: http://www.spammertrap.com