similar to: Shore wall and multi ISPs and ip addresses

Hi All! Been quite a few years and lots of water under the bridge but here I am back! I have a customer that has now decided they need a bit more bandwidth over and above their fixed line! They are not in a good area for ADSL because of copper theft and being a bit to far from the closest DSLAM! They have installed a wireless link and I have made certain that put it behind my simple iptables

Dino, Alexey, there are a number of users suffering issues with your Powercom devices. Could you (Dino, and Keven if possible) please have a look at the below one, from Angela, and check for a fix? I've scheduled to release 2.6.1 next week, and having that fixed is part of the list. 2011/5/16 Angela Williams <angierfw at gmail.com> > Hi All > > On Friday 13 May 2011 at

Hi All! Just an update! The snmp driver seems quite happy with an APC AP9618 managment card in an APC Smart-UPS RT 5000 XL UPS. I have an APC AP9630 to test in the near future so will give and update on that one too! Cheers Ang -- Angela Williams angierfw at gmail dot com Linux/Networking Hacker Blog http://angierfw.wordpress.com Smile! Jesus Loves You!

Hi everybody, I have my firewall with shorewall runing and I dont have a proxy. I would like to know which tool can I use to log my web traffic from my users. I have ntop working but I dont think this tool helps me on this. Any suggestion? Thanks ------------------------------------------------------------------------------ LogMeIn Rescue: Anywhere, Anytime Remote support for IT. Free Trial

Hi! Progress is much better now with my new install with not many problems left! I just have a simple - I hope - question. I have a few users that need access to the net via masquerade rules. The rest have to go via squid on the firewall. That all works well. I also have two windows servers that also need access to the net but they have to each use a specific outgoing ip address. I add two

Hello all, I''m reading the nice documentation about shorewall with multi isp. And I wonder about squid (non transparent) and shorewall Can I use on same machine, squid with ldap ident, dansguardian, and shorewall with multi-isp (four or five) ? Perhaps there is a problem because squid mask source IP, shorewall can maintain and load balance sessions for the same source IP ? Thanks Fred

Hi! Normally nut was just worked and worked for me! Not this time though! Distro is Gentoo withe latest nut-2.6.0 emerged today. Linux kernel version is 2.6.36 UPS is PowerCom BNT2000AT "Driver" is powercom ups.conf looks like this! Okay so APC1 is not and APC! [APC1] driver = powercom type = BNT port = /dev/ttyS1 numOfBytesFromUPS = 16

Hello Guys I have problem with internet bank. I have 2 Internet links balancing mode, thus the bank is charging connection down. I tried to force Internet traffic (port 80 and 443) for only a link, however it did not work. How do I make a setting to force the connection to these ports for a specific link. Note: I can not use the file as route_rules have neither the source IP (ltsp) nor of

The Shorewall Team is pleased to announce the availability of Shorewall 4.5.0. ---------------------------------------------------------------------------- P R O B L E M S C O R R E C T E D I N T H I S R E L E A S E ---------------------------------------------------------------------------- 1) This release includes all defect repair included in 4.4.27.1-4.4.27.3. 2) The start

When I attempt to start shorewall (version 4.0.15) I get an RTNETLINK error (see below). /var/log/shorewall-init.log [...] 21:02:18 Creating Interface Chains... 21:02:19 Adding Providers... RTNETLINK answers: File exists ERROR: Command "ip route add table 1 129.116.XXX.0/24 dev eth2 proto kernel s cope link src 129.116.XXX.30" Failed 21:02:25 Shorewall-generated routing tables and

Hi All, (please reply directly as I''m not on the mailing list ) I''m trying to setup a firewall for the below config but I''m not sure what set of rules or even how to go about it . Internal Subnet setup on Lab network with Sun Microsystems =========================================================== Firewall machine with Fedora and Webmin/Shorewall Installed

Hi! Normally nut was just worked and worked for me! Not this time though! Distro is Gentoo withe latest nut-2.6.0 emerged today. Linux kernel version is 2.6.36 UPS is PowerCom BNT2000AT "Driver" is powercom ups.conf looks like this! Okay so APC1 is not and APC! [APC1] driver = powercom type = BNT port = /dev/ttyS1 numOfBytesFromUPS = 16

how to make this work, its seem to me that netfilter is changed more or less someplaces that shorewall do not support, using 4.4.27 shorewall and shorewall6 suggestion welcomed ------------------------------------------------------------------------------ Try before you buy = See our experts in action! The most comprehensive online learning library for Microsoft developers is just $99.99!

I am in the process of building a new machine to replace several older servers. I am considering running several virtual servers on one box, all linux for host and virtual machines using VirtualBox. Is it possible/advisable to configure shorewall on the host to act as a firewall for the virtual machines, each having one or more static public IP address? Any pointers, suggestions and/or

Hi all and specially Mr. Tom.... (Please, do not be acid with me please! I am only a newbie, trying learn more about shorewall) I get involved with a Firewall Project in a customer here in my city... In this customer, he has two Internet Providers. So, he ask me how make certain connection following one routing path (like RT_1) and others connections type, following the other routing path

Hi, Shorewall version -4.0.12-2 (EL5 rpm version) OS : Centos 5.2 I have shorewall successfully running on Linux with multi ISP. Trying to make services such as "rsync, ftp" go through my secondary ISP. For which I did the following eth0 : Internal LAN eth4 : DSL (Second ISP) => x.x eth5 : T1 (First ISP) => y.y Created the following entries in

hi, I am running shorewall 3.2.9 on Mandriva2007 with 2 ISPs. Certain local IPs are directed to a specific ISP in route_rules, and this was working perfectly. I had to reinstall Mandriva, and after that this redirection is not working. My files are: masq: eth1 192.168.10.3 202.71.146.210 eth2 202.71.146.210 192.168.10.3 eth1 eth0 202.71.146.210 eth2 eth0 192.168.10.3 interfaces:

Hi all, I have the following configuration: _______ +------------+ / diginet link | | | +-------------+ Provider 1 +------- __ | | | / ___/ \_

hi I''ve got the situation that I have a virtual shorewall firewall/router which will get different single ip''s on one interface in different subnets with different gateways which need to be nat''ed to the inside network. I''d really love to do proxy arp but the provider isn''t able to give me an ip range (cloud computing hooray). If I understand it