similar to: Correct way to use quagga and shorewall

Hello! I have trouble with multipath routing. Those options are enabled in kernel: [*] IP: policy routing [*] IP: equal cost multipath [*] IP: equal cost multipath with caching support (EXPERIMENTAL) <*> MULTIPATH: round robin algorithm But issuing: ip r a 1.2.3.0/23 scope global equalize nexthop via 80.245.176.11 \ dev eth0 weight 1 nexthop via 80.245.176.13 dev eth0

Hello, does anybody know if quagga for CentOS 5.3 is compiled with -enable-multipath? I want to implement ECMP over 2 ISP. Thanks, Cristi Carstea

Hello All, Does anyone happen to be running Quagga on CentOS 5 with SELinux in enforcing mode? Have you had to create SELinux policies or did it "just work" out of the box? (I'll get around to building this out on CentOS 6 as well.) I'm simply trying to write my config (for the zebra daemon) and it can't be written... Looks like this bug from Fedora 8 in 2008 [0] remains

I was wondering if anyone is running Quagga on Xen? What is throughput/latency like? Was looking for about a gig of mixed packet size BGP throughput. Hardware is Opteron 4 Way Quad cores, was thinking paravirt with a couple of dedicated cores and maybe the addition of Solarflare 10GB Direct IO NICs might give the required performance level but I am unsure. The other option is multi-queue Intel

I have some problem with traffic shaping on debian testing. I actually posted a full config on the list a while ago but didn''t get any answers. The problem is that traffic doesn''t get into the user classes (~150) when I associate a class with a qdisc. I tried sfq, fifo but none works. If I dont''t associate a qdisc with a class classification occurs well.

Package: xen-hypervisor-3.0.3-1-i386-pae Version: 3.0.3-0-2 Severity: normal If quagga is running, and I start & stop a domain, the VIF interface doesn't go down properly (in addition to other problems). Here's what I do: 1. Boot the computer. By default, quagga is running (zebra + ospfd). 2. xm create test7.cfg, wait until the domU starts. 3. xm shutdown test7, wait until the domU

Hello all, Some time before Christmas, a project was started. The task was to enhance an existing LiveCD solution with User-mode Linux. A number of requirements was stated, where the greatest challenge was to fit 10 virtual routers within an old no-name PC with only 256MB Ram. And the solution must still be run from a LiveCD. Thanks to Xen, the task was possible to complete. -But, what does it

I'm looking for an open source router solution, and someone from the list recently recommended zebra (www.zebra.org). I haven't yet identified all my needs, but I'm guessing that it will do all my routing needs for a, say, class C set of IP addresses, particularly if I ever have to do anything BGP-related. Anyone have any pointers before I delve in? Or possibly a recommendation for

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi list, yesterday I sent this eMail to quagga mailing list, however I didn't receive an answer yet. Unfortunately, I really need this stuff running or have to switch to another strategy achieving the goals. Maybe one of you has some experience on this topic and can shed some light on it -- I really appreciate it. -

Hi, > Can you manually do on the xen interfaces what the scripts would? How about > doing it on some other interface configured in a similar way? Toying with the vif-route script, I might have found a workaround for this issue. If I disable the ifconfig and ip route commands from vif-route script, and bring up vif interface by hand later on, everything seems to work. In other works,

In a nutshell and very first of all, you need at least 2 internet connections. Those ISP must be willing to setup BGP peering between your routers and theirs. Once that agreement has been made, you need to get their AS Numbers and submit the ASN request located on ARIN's website (http://www.arin.net). After some paperwork and money exchanges, ARIN assigns you an AS number. At that point,

Hello, Here is my network: ------------------ ------------- ----------- Linux box ----------- GRE --------- Cisco ---------- ------------------ ------------- What I wan to accomplish. I want ripv2 to go across (both ways) through the GRE tunnel. No packets are being passed thought the GRE

Hi list, I have a problem I thought was simple first, but now I''m stuck. In a nutshell, it''s about redundant uplinks at an outside location. Crude ASCII-Art follows: Internet | | +------------+ | cisco with | | uplinks | +------------+ | | ATM interface +----------+ ... | alvarion | | | wireless

On 28/07/2010 15:45, shorewall-users-request@lists.sourceforge.net wrote: > On 7/28/10 1:50 AM, Andrea Perdicchia wrote: > >> > Hi all, >> > Is possible log mac address in shorewall? >> > I try all configuration "debug,info..." in /etc/shorewall/shorewall.conf >> > but in /var/log/messages the log show only few information and not mac

https://bugzilla.netfilter.org/bugzilla/show_bug.cgi?id=554 ------- Additional Comments From fhagur@gmail.com 2007-04-17 05:04 MET ------- I have been wondering about this bug and had similar problems myself here in my Debian system, linux-kernel 2.6.18 iptables 1.3.6. I too saw that some packets became transmitted illegally through the ppp0 interface, when they just shoudn't. What I

Hi folks, At work, we're considering the idea to replace the presente router with a stardard box with CentOS as a SO and GNU Zebra as a routing software. The line is a 4Mbps SDSL. ?What do you think about Zebra and what are your experiencies with it? Any feedback will be so appreciated. TIA.

Hi Guys, I would just like to have advice and pointers of the best way would be, Someting like BGP or OSPF? I have 2 internet connections at diffrent locations. let say connection A and B 1.) router A has a fast internet connection and a seperate interface for clients using /lan/pppoe/ipsec etc and another ethernet interface going to router B 2.) router B has similiar setup as router A and

Refering to pppoe i have next problem : I asked my isp if i can buy a class of real ip`s to be routed by them. They said elegantly it can`t be done . I want opinions . I am using an ADSL connection through a Speedtouch 510 configured in bridge. About Bgp : i asked someone if i can peer 2 different locations on 2 different ip`s using private asn number and he said yes , and what i don`t

Hi Everyone; Please find below a mail I sent to quagga mailing list, covering lartc/quagga issue. So far, I have no reply from them. I think that maybe you guys would have an idea about this. Thanks in advance ! Best, -----Forwarded Message----- Hi There, I''m new to quagga and to dynamic routing in general, so please forgive me if my question are foobar. I''m trying to

Before I start, I don''t want to do ECMP or simple bonding ... I have multiple Internet connections available to multiple boxes on one of my networks. Box A connects to ISPs 1, 2 and 3 Box B connects to ISPs 1 and 4 Boxes A and B are both connected to each other and the rest of the network. 1) I would like to set up some dynamic routing in such a way that any given outgoing packet from