similar to: Forcing ifcfg-eth0 to use the same nic in multi nic machine

I have a server with 4 nics. Two are using different internet connections, both with static IP's, and two are connected to our private network. The two internet facing nics seem to be battling over the gateway designation. Which ever I designate as the gateway the other stops responding to incoming traffic. I need both to listen to inbound traffic. One for our main web page and the other

What is happening in centos 5 with network config files??? I have a machine with 2 network cards. ifcfg-eth1 keeps changing to DHCP. All my static setup is gone. Why is it doing this? How can I stop it? I run "netconfig -d eth1" and re-setup my static information. I reboot and now I am back to DHCP. I have a gigabyte motherboard, nvidia chipset. forcedeth driver. eth0 is e1000.

I have two servers with identical hardware ... TYAN i3210w system boards with dual intel gigabit interfaces, and a PCI intel gigabit nic. I'm running Centos 5.4, x86_64, 2.6.18-164.6.1.el5 Every other time I reboot, the nics initialize in a different order. anaconda had setup /etc/modprobe.conf with alias lines for the cards: alias eth0 e1000 alias eth1 e1000e alias eth2 e1000e However,

1) I'm actually not building a custom kernel per se, just one from the standard 2.6.11.4 with our configuration. I may be adding a custom driver, but unless I can get the standard kernel to boot,... 2) I have been told that after 2.6.11.4, support for the Infiniband driver is dropped, and we need that. If this is not the case, I would be delighted to know that and proceed accordingly.

Me again. The ASUS P5N32-SLI motherboard in my new machine has dual NICs but CentOS has only detected one of them. I've tried rebooting with the network plugged in only to the second one, but kudzu still doesn't find it. Any suggestions?

On 15 August 2007, Les Mikesell <lesmikesell at gmail.com> wrote: <snip> > Everyone believed that except DECnet which expected all cards in the > same machine to have the same MAC. The address should be stored in a > ROM and initialized at startup, so it is probably a firmware or driver > bug. Les: On multiport cards, do the NICs all have different MAC addresses and do

Hello, I created a CentOS 5.0 x86_64 guest under Debian Etch with Xen 3.0.3 and it boots fine except for one re-occuring problem - whenever it boots the /etc/sysconfig/network-scripts/ifcfg-eth0 script gets renamed to .bak and doesn''t configure the ethernet device. Here is the content of this file: TYPE=Ethernet DEVICE=eth0 BOOTPROTO=static ONBOOT=yes IPADDR=192.168.0.247

Actually, here is what shows up in the log, regardless of whether the driver is built-in or loaded as a module: Feb 5 10:16:15 sparenode1 sysctl: net.ipv4.conf.default.rp_filter = 1 Feb 5 10:16:15 sparenode1 sysctl: net.ipv4.conf.default.accept_source_route = 0 Feb 5 10:16:15 sparenode1 sysctl: kernel.sysrq = 0 Feb 5 10:16:15 sparenode1 sysctl: kernel.core_uses_pid = 1 Feb 5 10:16:15 sparenode1

Hello Is there a way for the dhcp client to send the current host name of the machine when requesting a lease ? Currently I have to include a line like DHCP_HOSTNAME=appserver2 in my /etc/sysconfig/network-scripts/ifcfg-eth0, but I would like to tell the dhcp client to just 'also send the hostname' and then the client to get the current hostname itself, instead of having the name

When using ifcfg-eth0:x files in /etc/sysconfig/network-scripts/, should each file (where x increments appropriately) point to DEVICE=eth0:x or DEVICE=eth0:0? I apparently have my alias files all ifcfg-eth0:0 - ifcfg-eth0:7 show DEVICE=eth0:0. Is this right? It seems odd to me and while it does seem odd, the alias IPs are being appropriately responded to, answering pings and nameserver

This really isn't a CentOS specific queation but that is our server OS of choice. I manage a student file server and i would like to add cloud access to it. Basically i would like our students to have access to the same files at home that they have at school. This would allow them to start an asignment at home, finish it at school, and print it off without having to worry about losing their

I''ve been using Puppet now for a month or so and I''ve come to a problem that may warrant an additional Puppet metaparameter. I''m advocating the addition of a metaparameter called "preaction" (or something like that), which will perform some arbitrary action before the resource is modified. There may be a way to do this within Puppet already (with some

This is probably a stupid question, but I''m stumped. Practically every time my firewall boots (not often, but still) eth0 and eth1 exchange places (internet and intranet). How do I lock them down? SuSE 9.2, Shorewall 2.2.3. Thanks! Mike- -- Mornings: Evolution in action. Only the grumpy will survive. -- Please note - Due to the intense volume of spam, we have installed site-wide

I have a bug report in (0002288) on an install failure on my decTOPs (Centos 4.5 installed on them). I have tried a lot of combinations and it is getting tiring. What what happen, or rather how do I get the following to work: Put my HD into a computer (Compaq SSF that I have installed Centos 5 on with no trouble), install Centos 5, move the HD to the decTOP. Different Video card. No PS/2

Hello, I have a big problem with my servers. I have 4 NIC on all my KVM Servers but the most time on a start (restart) I lost one NIC? It is not always the same, but this two are virtio NICs. with ifup eth0(1) the system say,I have no configured eth0 or eth1 file ? Can any tell me what I can do? thank's for a answer NetworkManager is disabled. -- mit freundlichen Gr??en / best regards,

I want to move all my OS, services like Apache configuration and application (web server) files and folders to another brand new server. Both servers are running on Centos 7. i want to clone everything. My questions 1- what is the easiest way to do this? 2- do I need to partition hard-drive of new server exactly as old one? 3- Is there any changes to make on new server after full migration? 4-

Hi, I have a wireless network but no wired network. I need to access the net for the necessary installation of the wireless drivers in CentOS 5.1. Could anyone let me know how i can go about it!! My card is Intel PRO/Wireless 3945 -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello all, I'm having unusual difficulty configuring teaming with Centos 4.2. The 2 NIC's are Broadcom. The HW is HP DL360 and there is no teaming driver for RHEL4 since it comes with package (says HP). Since there is no teaming driver from centos (as far as I know), I tried the Broadcom Driver, configured the team file, but the team just wont come up. A Virtual Interface should be up

CentOS-5.5 # uname -a Linux inet05.hamilton.harte-lyne.ca 2.6.18-194.32.1.el5 #1 SMP Wed Jan 5 17:52:25 EST 2011 x86_64 x86_64 x86_64 GNU/Linux Can anyone tell me why I am seeing these error message? Specifically, why is TYPE=Bridge giving Unknown connection type 'Bridge'? Jan 13 08:25:31 inet05 nm-system-settings: Loaded plugin ifcfg-rh: (c) 2007 - 2008 Red Hat, Inc. To report bugs

CentOS-5 $ ll /etc/sysconfig/networking/profiles/* total 0 $ ll /etc/sysconfig/networking/devices total 0 CentOS-6 $ ll /sysconfig/networking/profiles total 4 drwxr-xr-x. 2 root root 4096 Oct 7 15:19 default $ ll /sysconfig/networking/profiles/* total 24 -rw-r--r--. 2 root root 158 Oct 7 15:19 hosts -rw-r--r--. 2 root root 116 Oct 7 15:19 ifcfg-br0 -rw-r--r--. 2 root root 238 Oct 7 15:24