similar to: Problems with USB-serial converters -- please advise on code fix

Hi Users NUT, I want monitor a UPS of brand SMS (Sinus Double 8 KVA) using a raspberry-pi. In compatibility list, is listed to use the blazer_ser driver. I use a USB adapter to RS-232 conected in to the No-Breake. Follow the comands e confs. root at rasp:/home/pi# lsusb *Bus 001 Device 004: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port* Bus 001 Device 003: ID 0424:ec00 Standard

[please use the nut-upsuser@ address rather than nut-upsuser-owner@ and be sure to use Reply-All - thanks!] On Dec 23, 2014, at 1:52 PM, Janez Kremzer <janez256 at gmail.com> wrote: > Hi! > > I woud like to use Raspberry Pi with NUT installed whic coud shut down NAS in the office. > NAS doesn't have comport and this is the reasion why not to use NAS directly. > >

hello everyone, I've been testing the NUT solution as opposed to the undocumented LanSafe application to control my Eaton UPS. I am on a Slackware 13.37 system with a 2.6.37.6 kernel. NUT version is 2.4.3 . I installed the tarball by compiling it directly on my system (as a slackbuild package). The UPS is an Eaton Powerware 9155, but I don't know how to obtain the manufacturing date. The

I have a USB to serial converter attached to my box. pl2303: Prolific PL2303 USB to serial adaptor driver if I login to the box and send/receive serial commands over this unit it works without error EVERY time. however, if I run the same command set from with-in the extensions.conf with System() I get errors in dmesg like "pl2303 ttyUSB0: pl2303_open - failed submitting read urb, error

>> I setup apcsmart driver on port /dev/ttyUSB0 in ups.conf and check that runing user=root. >> > user=root is only for testing- this may cause other permissions problems later. It looks like the simplest way to handle this on Debian is to add the system 'nut' user to the 'dialout' group: $ sudo adduser nut dialout > I have been meaning to collect some

I am trying to use software to program a scanner radio (BCD396t and UASD software). The software installs and seems to run properly, reading and writing database files. But I cannot connect to the scanner, through a USB-to-serial cable. OS: ubuntu-8.10, kubuntu-8.10, debian/lenny (tried them all) lsusb identifies the cable as follows: Bus 002 Device 002: ID 067b:2303 Prolific Technology, Inc.

Hi, I'm having trouble getting my Palm to sync with jpilot on my Centos system via USB. When I sync, I get this error in jpilot: pi_accept Illegal seek Exiting with status SYNC_ERROR_PI_ACCEPT Finished I have jpilot syncing fine with this Palm over the network, BTW. For USB, I set things up for udev as described on various websites. Here are the relevant ports & symlink (created

Hello, everyone - I have an old Windows app - a ship navigation program - that needs to see GPS input on a serial port (it was written in the pre-USB days.) My laptop, however, has no serial ports - but this same program, when run on a friend's Windows box, can read the GPS info from the USB-connected GPS via the "USB-Serial Driver". This is one of the frustrating bits of this

doctordruidphd wrote: > I am trying to use software to program a scanner radio (BCD396t and UASD software). The software installs and seems to run properly, reading and writing database files. But I cannot connect to the scanner, through a USB-to-serial cable. > OS: ubuntu-8.10, kubuntu-8.10, debian/lenny (tried them all) > > lsusb identifies the cable as follows: > Bus 002 Device

Hi all, I'm trying to configure Nut to connect to an APC BackUPS Pro 900VA. This ups uses a serial port on which _simple_ or _smart_ signaling should be spoken. I've connected the UPS to a serial port using the original 940_0128A cable from APC. Unfortunately I've not yet managed to read any data from the ups. If I try to load the apcsmart driver it tells me that it cannot communicate

Hi I have a serial UPS connected using a serial2USB device. Usually it is port=/dev/ttyUSB0, but occasionally i need port=/dev/ttyUSB1. How do you guys handle something like this? JonB

I've looked up the Kpilot manual, and I think I have an okay idea of what's going on with it. I'm trying to get it's detection feature to find my Palm Pilot. CentOS does seem to be able to recognize it, because if I run lsusb when running a hot sync, I get the following: [root at localhost dev]# lsusb Bus 001 Device 010: ID 0830:0060 Palm, Inc. Palm Tungsten T / Zire 71

I have been trying to get an EVDO modem to work with Centos 5. I can make it dial out with wvdial only when I'm the root user. Otherwise I get this error: Cannot open /dev/ttyUSB0: Device or resource busy I added the user to the uucp group. crw-rw---- 1 root uucp 188, 0 Dec 3 02:30 /dev/ttyUSB0 crw-rw---- 1 root uucp 188, 1 Dec 3 02:30 /dev/ttyUSB1 crw-rw---- 1 root uucp 188, 2 Dec

Yes I do have Linux. I have assigned the ups.conf file as seen below.. [testups] Driver = usbhid-ups Port = /dev/ttyUSB0 When I try to start the ups driver I get the following error... $ sudo upsdrvctl start Network Ups Tools - UPS driver controller 2.7.1 Network Ups Tools - Generic HID driver 0.38 (2.7.1) USB communication driver 0.32 No matching HID UPS found Driver failed to start (exit

2011/2/15 Lupe Christoph > On Monday, 2011-02-14 at 21:54:20 -0000, Arnaud Quette wrote: > > I definitely need more info! > > please reply to ALL: > > > - what is the exact model and date of manufacturing? > > SmartUPS 300I NET. I have the serial number (GS9809283199) but no date. > it seems to be a recent model. > - are you sure this unit is ok? > >

2011/2/15 Lupe Christoph > On Monday, 2011-02-14 at 21:54:20 -0000, Arnaud Quette wrote: > > I definitely need more info! > > please reply to ALL: > > > - what is the exact model and date of manufacturing? > > SmartUPS 300I NET. I have the serial number (GS9809283199) but no date. > it seems to be a recent model. > - are you sure this unit is ok? > >

I have a new APC Smart-UPS SUA2200RM2U. I've had no success with the manufacturer's PowerChute software and smart signaling, so I have decided to try NUT. The smartups driver can't make contact through the serial port. Since this is rack-mounted, it comes with a 940-1524 serial cable. As far as I can tell, this is supposed to work with smart signaling. Here's my ups.conf:

Ubuntu creates /dev/ttyUSB0 for me when I plug in the usb-to-serial-adapter. I have a symbolic-link to /dev/ttyUSB0 from 'dosdevices/com1'. What is new in 10.04 Ubuntu is that I have to sudo chmod o+r and sudo chmod o+w on /dev/ttyUSB0 every time before I start the app which uses that serial line. ttyUSB0 goes away when I unplug the serial adapter from the USB port or shut down the

On several occasions I have seen the apcsmart process runaway using 100% CPU while filling my syslog partition by logging the following syslog entries at an incredible rate. I have seen up to 21,800 log entries PER SECOND of the following nature: --[snip]-- Jun 25 10:06:38 servername apcsmart[4012]: Communications with UPS lost: Communications with UPS lost - check cabling Jun 25 10:06:38

Sorry for a bit longer delay than I anticipated, I was stuffed with the work. This is the next iteration of the patch adding some functionality to apcsmart driver, and relying on 'ignorelb' recently added. Follow up from previous thread: http://www.mail-archive.com/nut-upsdev at lists.alioth.debian.org/msg02331.html Main differences is that V3 is split into many small patches, so the