similar to: Allocating 64 kbits/s out of 256 kbits/s for one LAN behing firewall

Hi, I have a CENTOS BOX as a firewall . both iptabes and iproute 2 are running on it. pls see bleow for installed RPMs. [root at firebox ~]# rpm -qa |grep iptables iptables-1.2.11-3.1.RHEL4 [root at firebox ~]# rpm -qa |grep iproute iproute-2.6.9-3.EL4.7 It has 3 ethernet cards. pls see below. eth0 - internet ip (pls asume. 1.2.3.4/29 ). it connects to ISP router. eth1 - 192.168.100.254

Hello Samba experts, Please read all email because i'm desperate!!!!! I have problem on joining to LAN-s using Samba. Finally i got a solution to "see" booth workgroups on "Entire Network", but i'm having problem with stations located in LAN2. From any station located in LAN1, I can see LAN2 workgroup and the browse list with stations located in LAN2, but when

Hello to everyone, Here is the situation: [LAN1]---[eth3]/----------\ | LinuxBR |[eth2]---[LAN0]---[linuxGW]---[internet] [LAN2]---[eth4]\----------/ Whole LAN is in subnet 10.0.0.0/24. So I need: LAN0, LAN1, LAN2 could not see each other. LAN0, LAN1, LAN2 is in same subnet (10.0.0.0/24). All LANs have to get only internet. How can I configure LinuxBR to do so?

Hi, list members. I''ve been reading a lot about traffic control because at work we have the following configuration...... LINUX BOX _____ 100 mbit | | LAN1--------------|eth0 | | | 2 mbit SDSL | eth1|-------------------INTERNET 100 mbit | | LAN2--------------|eth2 | | | ------- The linux box (REDHAT 9-2.4.20-30.9) acts as a firewall-NAT solution for both

Dear Friends, I have been using shorewall for some years. I want to set up "shorewall 2" router behind firewall, accordind to this picture: I have lost at setuping "zone"-s (wifi, lan1, net). Plese help me ! Thanks, psw net | | SHOREWALL 1 ------- lan 1 | | |wifi | | SHOREWALL 2 ------- lan 2 | ---------------- lan 3

An very interesting test did yesterday that, LAN1 and LAN2 setup an tinc VPN which is quite simple(the physical link between tinc nodes are quite stable/fast), and no any application traffic to go through the tinc. Later, I setup smokeping which LAN1 initial 20 ping to LAN2 on a per-minute basis, but as you saw from the below picture, it had packet drop. But if I perform a constantly ping from

Hi Paolo Malfatti, Thanks for your script. It works fine. I get what I expect. THANK you all the way until it comes to an end. FOR the benifit for evryone in the LIST. HERE IS the SCRIPT AGAIN. INTERFAZ_LAN=eth0 FULLBANDWIDTH=256 BANDWIDTH4LAN=64 tc qdisc del root dev $INTERFAZ_LAN tc qdisc add dev $INTERFAZ_LAN root handle 1 htb r2q 4 tc class add dev $INTERFAZ_LAN parent 1: classid 1:2

 Hello, everybody.  This one''s got me stumped.  What I''m trying to do is have two networks--192.168.1.0 and 192.168.2.0--with SMB and WINS running between them.  So far I can mount SMB shares allright, but I can''t browse by WINS names across the router.  I''ve posted this question on Linuxquestions.org; you''ll find the details there.  Here are my

Hi, this is my Linux Box ---------------------------- LAN 1 -----|--eth1 <---br1--->eth0.1 | | \ | | eth0--|----- 802.1q tagged 1 Mbps link | / | LAN 2 -----|--eth2 <---br2--->eth0.2 | ---------------------------- I have to bridge the 2 lans

I have the following situation: A Linux 2.4.22 server: Physical ethernet: lan1 - Ethernet port (Internet) lan2 - Ethernet port (Cisco Switch, Trunk port) Tunnel: tap1 - OpenVPN in tcp-server mode VLAN's: lan2.201 lan2.202 lan2.203 tap1.201 tap1.202 tap1.203 Bridges: br201 (lan2.201, tap1.201) br202 (lan2.202, tap1.202) br203 (lan2.203, tap1.203) On the other end, the same type of server:

Hello, I am a newbie in Asterisk IP PBX but I am very impressed by its functionalities. I have read that It can work over IP network and across the PSTN. I am not very sure how it works over the PSTN.. In case if people have not yet the Internet or SDL access, I would like just to know if it is possible to interconnect two IP LANs using the traditionnal analog Network and Asterisk PBX? In such I

Hi all, I''ve got a BOX running CentOS 4.5. It acts as a firewall + router. I have installed both iptables and iproute2. I has 3 network cards. eth0 is connected to Internet (is has an internet ip. pls assume its ip is 1.2.3.4/29). it is a 256 Kbit link. eth1 is DMZ. its ip is 192.168.100.254 eth2 is LAN. Its ip is 192.168.101.254 I have alreday shaped traffic to 64 Kbit on eth1 for

On Thu, Mar 30, 2023 at 09:07:53PM +0200, Hans Schultz wrote: > Not true, it reveals that I forgot to put it in the patch, that's all. As > I cannot run several of these tests because of memory constraints I link > the file to a copy in a rw area where I modify the list and just run one > of the subtests at a time. If I try to run the whole it always fails > after a couple of

Hi, I'm using linux 2.6.21.5 and our kernel is freeze. The problem is, if I create a Software bridge using $brctl command. and add two interfaces say, eth0.0 and eth0.1 using $brctl addbr br-lan $brctl addif br-lan eth0.0 $brctl addif br-lan eth0.1 and when i send traffic from a host connected to one port to host connected at other end, soon all the memory is dried up and and kernel

Hi, I have a little problem to setup iproute in my network It looks like this: ---- ----- ------ R1 R2 R3 ---- ----- ------ | | | | | | ------------------------------- ETH1 ETH2 ETH3 ETH0 ETH4 -------------> DMZ ------------------------------ | |

Many thanks for the help to date. I now have a working vpn with three nodes: 10.20.30.1 10.20.40.1 10.20.50.1 Each machine can see each other machine 100's of miles apart from each other. Each machine is behind its own router. The machines are on their own subnets, as well, of course. The individual IP's on the lans of the nodes are: 192.168.0.155 (corresponds to 10.20.30.1)

Hello! I've got a problem with DNS,VPN and SAMBA. I do have 3 Linux servers on distinct subnets. (192.168.1.1 ,192.168.2.1 and 192.168.3.1). I have done a VPN between the 3 subnets and I could do a ping from 192.168.1.1 to the others without problems. Each sever has 2 network cards. One of them is connected to ADSL.

Hi, we have a trust relationship between servers in the 2 LAN's of my company, my problem is that (even with problems as I commented in a previous mail) I have somekind of access to the LAN where my Linux machine is connected to, but not to the "trusted" LAN. Could someone give me a hint about how to get this? Any kind of documentation would be helpful.... Regards, Juan

Hey guys! To make the adoption of IPv6 networks with Samba4 more smooth / robust, I think that it is vital to give to Samba4, the ability for it, to join a IPv4-Only Secondary DC, into a Dual-Stacked Primary DC. This doesn't work today. Otherwise, these days to enable IPv6 within a "Samba4 AC DC" network, it is a requirement to enable it, simultaneously, on each and every network

Hi Friends, I am running Centos 5 64-bit on a Dell sever. I am trying to configure iptables for smtp traffic for which I need some help/guidance. The scenario is like this: On a linux box we have 3 public ips(eth1,eth2 and eth3) and 1 LAN IP(eth0). 2 public IPs are from the same service provider and 1 is from different service provider. eth3 and eth2 are from the same public provider but