similar to: UID/GID access control in Lustre

Hi, Lustre manual 1.6 v18 says that that in production lustre debug level should be set to fairly low. Manual also says that I can verify that level by running following commands: # sysctl portals.debug This gives ne following error error: ''portals.debug'' is an unknown key cat /proc/sys/lnet/debug gives output: ioctl neterror warning error emerg ha config console cat

Hi all, I''m getting my feet wet in the infiniband lake and of course I run into some problems. It would seem I got the compilation part of sles11 kernel 2.6.27 + Lustre 1.8.3 + ofed 1.4.2 right, because it allows me to see and use the infiniband fabric, and because ko2iblnd loads without any complaints. In /etc/modprobe.d/lustre (this is a Debian system, hence this subdir of

I am running on CentOS 5 distribution without adding any updates from CentOS. I am using the lustre 1.6.4.1 kernel and software. I have two NICs that run though different switches. I have the lustre options in my modprobe.conf to look like this: options lnet networks=tcp0(eth1,eth0) My MGS seems to be only listening on the first interface however. When I try and ping the 1st interface (eth1)

Hi all, Here is the situation: I have 2 nodes MDS1 , MDS2 (10.0.0.22 , 10.0.0.23) I wish to use as failover MGS, active/active MDT with zfs. I have a jbod shelf with 12 disks, seen by both nodes as das (the shelf has 2 sas ports, connected to a sas hba on each node), and I am using lustre 2.4 on centos 6.4 x64 I have created 3 zfs pools: 1. mgs: # zpool

Hello, Not sure if this is the right forum: I''m encountering difficulties with o2ib which prevents an LNET shutdown from proceeding: Unloading OpenIB kernel modules:NET: Unregistered protocal family 27 Failed to unload rdma_cm Failed to unload rdma_cm Failed to unload ib_cm Failed to unload ib_sa LustreError: 131-3: Received notification of device removal Please shutdown LNET

Greetings! I am working with Lustre-2.1.2 on RHEL 6.2. First I configured it using the standard defaults over TCP/IP. Everything worked very nicely usnig a real, static --mgsnode=a.b.c.x value which was the actual IP of the MGS/MDS system1 node. I am now trying to integrate it with Pacemaker-1.1.7. I believe I have most of the set-up completed with a particular exception. The "lctl

Hello, I use Julian Anastasov ''routes'' (to be more specific: static_routes, alt_routes and nf_reroute) patches on a 2.4.32 kernel. On the same host I run IPSec. I have discovered after a few hours of networking problems that, when IPSec is enabled on that patched kernel, inspecting packets with tcpdump while arping-ing a host from a network physically connected to this

Hi, I would like to know what TCP/UDP ports should i keep open in my firewall policies on my MGS server such that I can have my MGS server fire-walled. Also if in a event of loss of MGT would it be possible to recreate the MGT without loosing data or bringing the filesystem down (i.e. by using cached information from MDT''s and OST''s) Thanks Anand

Chris, Perhaps you need to perform some write_conf like command. I''m not sure if this is needed in 1.6 or not. Shane ----- Original Message ----- From: lustre-discuss-bounces at lists.lustre.org <lustre-discuss-bounces at lists.lustre.org> To: lustre-discuss <lustre-discuss at lists.lustre.org> Sent: Fri Mar 07 12:03:17 2008 Subject: Re: [Lustre-discuss] Multihomed

Hi all, I used the method described below to build client rpms with the source kit lustre-1.8.5.tar.gz. There was only one error reported during the make rpms, relating to lustre-iolit-1.2-root, but the rpms were built under /usr/src/packages/RPMS/x86_64. The rpms lustre-modules, lustre and lustre-tests were then installed smoothly without any complaints. But the subsequent "modprobe

Hello All, I have installed and configured Lustre 1.8.4 on SuSe 11.0 and everything works fine if i run modprobe lustre and when the lustre module is getting loaded. But when the server reboots it is not getting loaded. Kindly help. Lnet is configured in /etc/modprobe.conf.local as below. options lnet networks=tcp0(eth0) accept=all For loading lustre module i tried including lustre module in

Hello I''ve noticed that Lustre network error, especially LND errors, are considered as maskable errors. That means that on a production node, where debug mask is 0, those specific errors won''t be displayed if they happened. Does that mean that they are harmless? Do upper-layers resend their RPC/packet if LNDs report an error? When, in my case, o2iblnd says something like

Hello I''ve noticed that Lustre network error, especially LND errors, are considered as maskable errors. That means that on a production node, where debug mask is 0, those specific errors won''t be displayed if they happened. Does that mean that they are harmless? Do upper-layers resend their RPC/packet if LNDs report an error? When, in my case, o2iblnd says something like

Hello, I am having trouble installing the server modules for lustre 2.1.4 and use mellanox''s OFED distribution so we may use infiniband. Would you folks look at my procedure and results below and let me know what you think? Thanks very much! The mellanox ofed installation builds and installs some kernel modules too, so I used this method to ensure OFED compiled against the correct

?Hola, Es más fácil que todo eso... Es que en tu fichero de entrada, la segunda fila son las unidades de las variables que tienes en la primera fila, pero "R" al leerlas las considera como un string que altera la clase de toda la columna cuando ésta es numérica. Simplemente eliminando esa segunda fila, las columnas acaban teniendo la clase que deben..

It seems that lustre puts its modules in /lib/modules/2.6.16.21-0.8-default despite the fact that my kernel is 2.6.16.21-0.8-smp ! uname -a Linux n32 2.6.16.21-0.8-smp #4 SMP Sun Sep 24 08:47:30 BST 2006 i686 i686 i386 GNU/Linux make[3]: Nothing to be done for `install-exec-am''. /bin/sh ../../mkinstalldirs /lib/modules/2.6.16.21-0.8-default/kernel/fs/lustre /usr/bin/install -c -m 644

Hi there, When Lustre is configured in an environment where there are multiple paths to the same destination of the same length (i.e. two paths, each one hop away), which path(s) will be used for sending and receiving data? I have my cluster configured with two OSTs with two GigE NICs in each. I am seeing identical performance metrics when I use LACP to aggregate, and when I use two separate

Hello, I am planning on deploying a few more clients in my lustre environment and was wondering which client version to install. I know it is okay to run a newer client version than your lustre server for upgrade purposes. However, would it be okay to be in this state for a longer period of time (for the life of this filesystem)? My lustre server is currently running 1.8.1.1 on RHEL 5.3 and I

I have a TDM card in a asterisk machine. I found that once I used it to call out, the call status changed to "connected" even the callee is still ring. How could asterisk distinguish the "ringing" and "connected" in zap channel? thanks.

Hi, We''re setting up fairly large Lustre 2.1.2 filesystems, each with 18 nodes and 159 resources all in one Corosync/Pacemaker cluster as suggested by our vendor. We''re getting mixed messages on how large of a Corosync/Pacemaker cluster will work well between our vendor an others. 1. Are there Lustre Corosync/Pacemaker clusters out there of this size or larger? 2.