similar to: One Internet IP private, One Internet IP Public

Hi Is there a way of marking packets by mac address instead of ip or ports using a "tc filter u32 match"? I read somewhere that I could use the offset -8 and -14 to grab the mac addresses but if I use anything lower than -8, for example -9, I get an error. I''m modifying the wondershaper script to cap the download speed by mac address. Any sugestions?

Hi, I'm having problems with setting up my ISA LineJack card on Linux machine... I've done everithing according to documentation available, by compiling the new ixj driver (v1.2.1), loading it, adding device node /dev/phone0 with major number 100 and minor number 0, adding aliases into the /etc/modules.conf: alias char-major-100 phonedev alias char-major-100-0 ixj and running depmod

Here''s a challenging problem for you experts to tackle: I''m trying to shape traffic going into an IPSEC interface which then goes over a DSL PPPoE interface. I figure I need to shape the DSL interface to keep it''s hardware queue mostly empty, and to

Hello all, I have been doing a lot of archive searching over the last week reading posts on IMQ and it''s apparent stability / instability. I have seen a number of posts about it not being maintained as well. Can anyone talk to me about IMQ''s stability in a heavy throughput environment (20 Mbps) and what was causing IMQ to fail if you know. Thanks, Mike

Hi all, this is really not really very easy to understand, or, to get in. Well, I''ve the following configuration on the router box: LAN - interface: eth0 - network: 192.168.2.5/24 - bandwidth: 100Mbit/s INET interface - interface: ppp0 - network: .dynamic.ip./0 - bandwidth: DOWN=1536kbit/s and UP=256kbit/s the LAN interface is to serve 6 other clients with internet and

I''m trying to setup traffic shaping on my linux gateway/router. The system has 3 interfaces: eth0 - My LAN - with IP address 192.168.0.254 eth1 - The ethernet connection to which my ADSL modem is connected. This has a 10.25.x.x IP, more on this later. The ADSL link has an upstream of ~1.2mbit. ppp0 - The PPP connection which is my WAN connection, with a real world IP. The system acts

Hi all, I have a little problem with my home-made slackware linux server. Here is the scenario: 1. I have a local wifi network 2. my server do masquerading and exit in internet via a PPPoE connection Goals: 1. not use SQUID 2. shaping the traffic with classes 3. emule connection must have minimum priority and a band-limit of 10KBytes/s in uplink (server--->internet) Any idea? Thx, Diego --

Hi!!! I'm trying to implement a SUS server (local windows update) I-ve already solved my problem to modify registry in order to establish windows update configuration. Now i've a quiestion all my client logon my samba PDC enusing a netconfig.pol isend all configuration everithing works ok. But i've a trouble, my users don't have privileges to install anything and i don't

Hello, I''m trying to get lossless VoIP traffic over my 3000k/500k ADSL line. Shaping outgoing traffic is no problem: I set total ceil for outgiong device (ppp0) to 450kbit and put VoIP into highest prio class. Even during full upload the voice is clean on the other end. Now I tried to get the same result for incoming data. I attached HTB to eth1 where the incoming voip traffic is

Cristian and Alex, Both of you have asked about this. A routing table can only have one default route so when the second link comes up, adding the second default route will fail. So in general, Shorewall can only reliably detect the gateway for P-T-P connections which is what the CVS current code does. -Tom -- Tom Eastep \ Nothing is foolproof to a sufficiently talented fool Shoreline, \

Hi, How i reduce the traffic of a computer to internet only. Not my lan I did try with this, but it''s useless: tc qdisc add dev ppp0 root handle 1: htb tc class add dev ppp0 parent 1: classid 1:1 htb rate 128kbit burst 6k tc filter add dev ppp0 parent 1: protocol ip u32 match ip dst 192.168.0.2 flowid 1:1 Can u give me a hand ?

Hey, I''ve been scouring the web these past few days trying to find a suitable technique to load balance my network. Unfortunately I think my setup is very uncommon, so I''m looking to you guys to see if you can help. I currently have 2 ADSL modems, provided by the same ISP and terminating on the same gateway (I think having the same gateway is what is causing the problems, since

Okay, here''s the deal, (diagram below) I currently have 3 NIC''s configured in my Linux server. eth0 serving the home network eth2 Cable modem to internet ppp0 ADSL to internet (through eth1) Connections can be established from eth0 (192.168.0.0/255) and from eth2 (24.250.85.128/128). Because eth2 has the first default route. However, ppp0

Hello! My goal is to setup an ingress traffic shaping on my PPPOE DSL line with ifb. My old imq stuff used iptables marks (like ''iptables -t mangle -A PREROUTING -p tcp --sport 22 -m length --length :500 -j MARK --set-mark 31'') to classify the traffic and since i am lazy, i tried to to reuse them with ifb. But no luck: iptables marks the packets well, but tc

I cannot connect to the INTERNET via my stand alone computer or my wireless laptop with the /etc/shorewall/interface setting I have. What Interface setting will allow me to connect to the Internet? Please see attached document for more details. ------------------------------------------------------------------------------ Free Software Download: Index, Search & Analyze Logs and other IT

Ok ladies and gents, I give up! I just can''t find a solution to the problem. Setup: I have a linux box with 2.4.22-1.2197.nptl kernel running 2 eth and one ppp connection over one of the eth for VPN tunneling. I have 2 needs: - masq and forward internal lan hosts via the tunnel on PPP and then on to the big internet. No problem there. All works fine. - Forward ppp0 native

Hi all, I have the following configuration: _______ +------------+ / diginet link | | | +-------------+ Provider 1 +------- __ | | | / ___/ \_

I can't get the sip to work. I am getting so frunstrated. It seems that this should be so easy to do. My XP has no settings to forward the RTP ports. How is this suppose to work. They describe it all over the internet that it will work, but I need the exact details. I have spent way to much time for what I have (nothing). Please help

Hello, i have a htb setup where the root and (nearly) all child classes has a ceil rate with max up from my adsl line. But the root class don''t reach the ceil value but some childs are get a huge backlog. My setup: (tc -d class show dev ppp0) [cleaned a bit] ******************************************************** class htb 1:1 root rate 576000bit ceil 576000bit burst 30Kb/8 cburst

Hi to everyone, this is my first post to the list. I'm developing an application for a Fujitsu MCU (90364 series) using Fujitsu Softune6 Workbench in linux under wine. Everithing works well exept for the firmware serial uploader. It starts and sends some commands to the MCU but hangs with a timeout error (obviously I've correctly simlinked and chmodded the appropriate ttyS*). To