similar to: ocfs crashes client with multipath iscsi

I people, i install the ocfs in my virtual machine, with centos 5.3 and xen. But when i turn off the machine1, the ocfs start the fencing off the machine2. I read the doc in oracle.com, but could not solve the problem. Someone help? My conf and my package version. cluster.conf node: ip_port = 7777 ip_address = 192.168.1.35 number = 0 name = x1 cluster

Below are the o2cb driver configuration and the tail of my cluster.conf. Here is the error I get when trying to start my cluster: [root at pbx_1 ~]# /etc/init.d/o2cb online Starting O2CB cluster pbx: Failed o2cb_ctl: Memory allocation failed while setting cluster name Stopping O2CB cluster pbx: OK I figure I am running out of memory (1GB!?) Maybe the driver is not configured properly? If

Hi I have: SLES 10 SP2 (2.6.16.60-0.21-smp) ocfs2-tools-1.4.0-0.3 ocfs2console-1.4.0-0.3 and I can't change "heartbeat dead threshold" value. Content of /etc/sysconfig/o2cb: # O2CB_ENABLED: 'true' means to load the driver on boot. O2CB_ENABLED=true # O2CB_BOOTCLUSTER: If not empty, the name of a cluster to start. O2CB_BOOTCLUSTER=ocfs2 # O2CB_HEARTBEAT_THRESHOLD:

One more follow on, The combination of kernel.panic=60 and kernel.printk=7 4 1 7 seems to have netted the culrptit: E01-netconsole.log:Jan 18 09:45:10 E01 (10,0):o2hb_write_timeout:137 ERROR: Heartbeat write timeout to device dm-12 after 60000 milliseconds E01-netconsole.log:Jan 18 09:45:10 E01 (10,0):o2hb_stop_all_regions:1517 ERROR: stopping heartbeat on all active regions.

Hello, this is my scenario: 1)I've created a Pacemaker cluster with the following ocfs package on opensuse 11.3 64bit ocfs2console-1.8.0-2.1.x86_64 ocfs2-tools-o2cb-1.8.0-2.1.x86_64 ocfs2-tools-1.8.0-2.1.x86_64 2)I've configured the cluster as usual : <resources> <clone id="dlm-clone"> <meta_attributes id="dlm-clone-meta_attributes">

Hi. I'm running RHEL4 for my test system, Adaptec Firewire controllers, Maxtor One Touch III shared disk (see the details below), 100Mb/s dedicated interconnect. It panics with no load about each 20 minutes (error message from netconsole attached) Any clues? Yegor --- [root at rac1 ~]# cat /proc/fs/ocfs2/version OCFS2 1.2.0 Tue Mar 7 15:51:20 PST 2006 (build

Hi to all, this is My first time on this mailinglist. I have a problem with Ocfs2 on Debian etch 4.0 I'd like when a node go down or freeze without unmount the ocfs2 partition the heartbeat not fence the server that work well ( kernel panic ). I'd like disable or heartbeat or fencing. So we can work also with only 1 node. Thanks

Greetings ocfs2 folks, A client is experiencing some random deadlock issues within a cluster, wondering if anyone can point us in the right direction. The iSCSI connection seemed to have dropped on one node briefly, ultimately several hours later landing us in a complete deadlock scenario where multiple nodes (Node 7 and Node 8) had to be panic'd (by hand - they didn't ever panic on

Hi all, I'm running OCFS2 on two system with OpenSUSE 10.2 connected on fibre channel with a shared storage (HP MSA1500 + HP PROLIANT MSA20). The cluster has two node (web-ha1 and web-ha2), sometimes (1 or 2 times on a month) the OCFS2 stop to work on both system. On the first node I'm getting no error in log files and after a forced shoutdown of the first node on the second I can see

We've been wrestling with this for ... rather longer than I'd care to admit. Host / initiator systems are a number of real and virtualized CentOS 5.5 boxes. Storage arrays / targets are Dell MD3220i storage arrays. CentOS is not a Dell-supported configuration, and we've had little helpful advice from Dell. There's been some amount of FUD in that Dell don't seem to know what

Greetings, On 1/22/11, Edward Morbius <dredmorbius at gmail.com> wrote: > CentOS is not a Dell-supported configuration, and we've had little helpful > advice from Dell. There's been some amount of FUD in that Dell don't seem > to know what Dell's own software installation (the md3 > > Dell doesn't seem to have much OS experience generally. > +1 It is

hi everybody, when using enable privileges = yes in smb.conf where does the permission get saved? I assume in the passdb backend or is there a tdb server specific file in /var/lib/samba? cause when i give a group the permission: net rpc -S pa-server1 rights grant 'NET\domadmin' SePrintOperatorPrivilege Enter root's password: Successfully granted rights. but when listing the

Hello, We have a 3-node cluster setup with ocfs2. Since friday one of the nodes went down and would not become clustermember after a reboot because it was unable to write to the ocfs2 filesystem. Message: no space left on device. There is plenty of diskspace though. No problem whatsoever to create a file / directory on the filesystem using one of the other nodes. Today one of the remaining

I am trying to mount the same partition from a KVM ubuntu 8.04.1 virtual machine and on an ubuntu 8.04.1 host server. I am able to mount the partition just on fine on two ubuntu host servers, they both talk to each other. The logs on both servers show the other machine mounting and unmounting the drive. However, when I mount the drive in the KVM VM I get no communication to the host

advanced in the printer-settings on windows) But if the driver does not get copied over? best regards thomas ________________________________________ Von: "Daniel M=C3=BCller" <mueller at tropenklinik.de> An: "Thomas Stegbauer" <mailingliste1 at stegbauer.info>, "Laurent Blume" = <laurent at opensolaris.org> CC: samba at lists.samba.org Gesendet:

Hi all, currently we have troubles with the constellation of Office 2007 / 2010 and samba 3.6.6 on Debian 7.5. I can open a Excel file only one time without a write protection. The File is protected on the second try. I can move and copy the file wihtout any Problems. If I move such a Excel File I can open it again for only one time without a write Protection. I already reseted and checked

d in the printer-settings on windows)=20 But if the driver does not get copied over?=20 best regards=20 thomas=20 ----- Urspr=C3=BCngliche Mail ----- Von: "Daniel M=C3=BCller" <mueller at tropenklinik.de>=20 An: "Thomas Stegbauer" <mailingliste1 at stegbauer.info>, "Laurent Blume" <lau= rent at opensolaris.org>=20 CC: samba at lists.samba.org=20

backgroud: there is a network idle timeout regarding which a node is considered dead or network partition occures. problem: for some product environment, there is a special time during a day. in this special time, a backup work is happening over private network. at the time that the backup is going on, there is very very high load on network. this can lead to ocfs2 network idle timeout and

Hello all, I'm running Samba 3.5.5 on Debian 5, and following the documentation as closely as I can to install drivers using rpcclient. I first install the driver on a Windows 7 x65 workstation, then use rpcclient/smbclient to fetch the files. I then use smbclient to put those on the print$ share of the Samba server. So far, so good. Then I use rpcclient to add those files, and that

Hello All, I have multiple OCFS2 clusters on SLES10 SP2 running Xen. We needed to increase the O2CB_HEARTBEAT_THRESHOLD from 31 up to 61 and did so successfully on 2 of our 3 clusters. However on one of the three clusters we are not able to change the value. The /etc/sysconfig/o2cb file contains 61 as the threshold after reconfiguring via /etc/init.d/o2cb configure, we reconfigure all 3 nodes at